• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.197.2-197.2
• /
• 2010

The study on the operation characteristics of solar space and water heating system with ground source heat pump (GSHP) as a back-up device was carried out. This system, called solar thermal and geothermal hybrid system (ST/G), was installed at Zero Energy Solar House II (KIER ZeSH-II) in Korea Institute of Energy Research. This ST/G hybrid system was developed to supply all thermal load in a house by renewable energy. The purpose of this study is to find out that this system is optimized and operated normally for the heating load of ZeSH-II. Experiment was continued for seven months, from October to April. The analysis was conducted as followings ; - the contribution of solar thermal system. - the appropriateness of GSHP as a back-up device. - the performance of solar thermal and ground source heat pump system respectively. - the adaptation of thermal peak load - the operation characteristics of hybrid system under different weather conditions. Finally the complementary measures for the system simplification was referred for the commercialization of this hybrid system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.223-226
• /
• 2004

MgO thin films were deposited bye-beam evaporation on $SiO_2$/Si wafers for the application of a protective layer in alternating current plasma display panels (AC-PDPs). Three different MgO sources, single crystal, melted polycrystal and sintered polycrystal, were used to find out the change of the properties of MgO protective layer depending on the source type. The properties of MgO thin films such as density, orientation and surface morphology were influenced by the source type. MgO thin films deposited with the melted polycrystal source had the highest density with the highest (100) preferred orientation, whereas the films deposited with the sintered polycrystal source had the lowest density with less preferred orientation. Such a result seems to be originated from the different mobility of adatoms on the surface of the deposited MgO thin films. Different microstructures of MgO thin films deposited even in the same deposition condition were observed depending on the MgO source type, resulting in different discharge characteristics.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.4
• /
• pp.16-23
• /
• 2011

Since the first lighting light source was invented, lighting has turned into superior-quality lighting considering the amenity of occupants, and the characteristics of a light source has developed rapidly. So this research confirmed the lighting performance of a dimmer control system and an ON-OFF control system via the existing light source, and analyzed the basic lighting environment of Permanent Supplementary Artificial Lighting of Interiors(PSALI) through the physical comparison and evaluation of a LED lamp substituted for a fluorescent lamp used in a dimmer control system, showing that the lighting physical quantity characteristics of an ON-OFF control system and a dimmer control system are similar to each other and that they are effective in terms of energy saving. Besides, it was shown that introducing a LED light source to a dimmer control system improves lighting environments and largely reduces energy consumption.

• Korean Management Science Review
• /
• v.20 no.2
• /
• pp.1-16
• /
• 2003

Previous research on data extraction and integration for data warehousing has concentrated mainly on the relational DBMS or partly on the object-oriented DBMS. Mostly, it describes issues related with the change data (deltas) capture and the incremental update by using the triggering technique of active database systems. But, little attention has been paid to data extraction approaches from other types of source systems like hierarchical DBMS, etc. and from source systems without triggering capability. This paper argues, from the practical point of view, that we need to consider not only the types of information sources and capabilities of ETT tools but also other factors of source systems such as operational characteristics (i.e., whether they support DBMS log, user log or no log, timestamp), and DBMS characteristics (i.e., whether they have the triggering capability or not, etc), in order to find out appropriate data extraction techniques that could be applied to different source systems. Having applied several different data extraction techniques (e.g., DBMS log, user log, triggering, timestamp-based extraction, file comparison) to S bank's source systems (e.g., IMS, DB2, ORACLE, and SAM file), we discovered that data extraction techniques available in a commercial ETT tool do not completely support data extraction from the DBMS log of IMS system. For such IMS systems, a new date extraction technique is proposed which first creates Index database and then updates the data warehouse using the Index database. We illustrates this technique using an example application.

• Applied Science and Convergence Technology
• /
• v.27 no.3
• /
• pp.47-51
• /
• 2018

We fabricated an anode-type ion beam source and studied its driving characteristics of the initial extraction of ions using two driving mechanisms: a diffusion phenomenon and a charge repulsion phenomenon. For specimen exposed to the ion beam in two methods, the surface impurity element was investigated by using X-ray photoelectron spectroscopy. Upon Ar gas injection for plasma generation the ion beam source was operated for 48 hours. We found a Fe 2p peak 5.4 at. % in the initial ions by the diffusion mechanism while no indication of Fe in the ions released in the charge repulsion mechanism. As for a long operation of 200 min, the temperature of ion beam sources was measured to increase at the rate of ${\sim}0.1^{\circ}C/min$ and kept at the initial value of $27^{\circ}C$ for driving by diffusion and charge repulsion mechanism, respectively. In this study, we confirmed that the ion beam source driven by the charge repulsion mechanism was very efficient for a long operation as proved by little electrode damage and thermal stability.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.22 no.3
• /
• pp.303-315
• /
• 1998

Numerical and experimental studies on a heat pipe with two heat sources have been performed to investigate the operating characteristics. Numerical analysis was performed based on the cylindrical two-dimensional incompressible laminar flow for the vapor space and the conjugate heat transfer for the entire heat pipe. Experimental study with a 0.45 m length copper-water heat pipe was also performed to validate the numerical modeling for the heat input range from 29 W to 47 W on each heater. As results, the temperature profiles at the outer wall for the single active heat source as well as the temperature profiles for the switching operation between two heat sources are suggested. Due to the axial conduction, it is found that the temperature drop between the evaporator and the condenser appears small when the heat source closer to the condenser is turned on. For the switching operation in the present study, the transient time is about 700s and the temperatures at the locations of both heat source are same in 130s after switching.

• Journal of Korean Society on Water Environment
• /
• v.33 no.1
• /
• pp.97-106
• /
• 2017

In this study, the characteristics of nonpoint source pollutant loads from separate sewer overflow (SSO) and combined sewer overflow (CSO) were evaluated during 2016 in Namyangju city, Korea. Five rainfall events were monitored during 2016 with ranging from 14.5 mm to 121.5 mm. The runoff ratio of CSO was higher than that of SSO because only design volume of maximum sanitary sewer ($1Q_h$) was transported and treated and $2Q_h$ was overflowed to waterbody during rainy day although combined sewer system was designed to transport $3Q_h$ to treatment system. The event mean concentrations (EMCs) and pollutant loads from CSO were higher than those from SSO. BOD and COD of CSO, and TOC and TN of SSO represented distinct first flush phenomena. The inadequate management in combined sewer system from which the untreated $2Q_h$ from CSO was overflowed to waterbody during rainy day could influence on high pollutant loads and first flushing. Treating $2Q_h$ from CSO, source control such as low impact development, and treating outflow from SSO were strongly recommended to control non-point source pollution in urban area.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.433-436
• /
• 2018

A total internal reflection (TIR) linear lens of size $190(W){\times}5(D){\times}2.1(H)mm^3$ has a directivity of $25^{\circ}$ and was made of a polydimethysiloxane (PDMS) silicone resin with a refractive index of 1.4 and a transmittance of 93% at 365 nm UV wavelength. A light source with a size of $190{\times}25.5mm^2$ was fabricated by installing a TIR linear lens on a chip on board (COB) type LED module mounted with a $1.1{\times}1.1mm^2$ size UV LED. The optical characteristics of the light source showed a maximum irradiation density of $3,840mW/cm^2$ at a working distance of 5 mm and a high uniformity of 91.6% over a $150{\times}25mm^2$ irradiation area. The thermal characteristics of the light source were measured at a supply current of 500 mA. The saturation temperature was reached after 30 min of operation, and measured to be $95^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.759-765
• /
• 2006

Temperature distribution of the circular heat source was studied by analyzing the heat transfer of the environment of the circular source for OLED. Circular nozzle source was used to fabricate thin organic layer as the organic material in it was heated, vaporized and deposited to the large size flat panel. Circular source for large size fat panel for OLED has been modified to obtain higher productivity and heat transfer characteristics was predicted using computer simulation. Fundamentals for OVPD process also was presented to estimate flow and heat transfer characteristics of the process which can increase the material efficiency.

• Fire Science and Engineering
• /
• v.28 no.2
• /
• pp.54-63
• /
• 2014

The purpose of this study is to test the adaptability of the CO sensor as a fire detector by analyzing its sensing characteristics on fire. In order to test the applicability, we designed and made a fire testing ground whose size is similar to that regulated by UL 268, carried out real fire tests suggested by UL 268, and conducted a comparison analysis on the sensing characteristics between the CO sensor and a photoelectric smoke detector by different types of fire source. The experiment result to the sensing characteristics of the CO sensor is about twice to three times faster than that of the photoelectric smoke detector, proceeding with incomplete combustion such as paper and wood fire source in the initial fire. Especially in case of wood smoldering fire, sensing characteristics of the CO sensor is very excellent.