• 한국소음진동공학회논문집
• /
• 제14권11호
• /
• pp.1153-1160
• /
• 2004

In contemporary society, vibration and noise in the road nearby buildings have become social problems as vehicles operation has increased. Especially. in the case of the building used to art performance, available suitability of the building is tested by the indoor noise class. Therefore, the Purpose of this paper is the measurement of the structure-borne noise of Seoul Art Center nearby Umyeonsan tunnel and analyzing the effects of countermeasure to it. To measure the effects of countermeasure, not only structure-borne noise is measured, but also the vibration is measured, before and after the construction of Pavement using pad and porous asphalt. Consequently, the sound pressure level in art center 1st floor is reduced after mat pavement method, structure-borne noise that was high In 25Hz wide-band before pavement decreased regardless of experimental vehicle's velocity Using porous asphalt pavement the noise was reduced about 3 dB(A).

• 한국소음진동공학회논문집
• /
• 제19권4호
• /
• pp.425-432
• /
• 2009

Recently, reduction of road traffic noise in residential buildings has become one of the most important subjects. To reduce the road traffic noise, noise impact assessment by the road traffic prediction model is required before building construction. For reasonable road traffic noise prediction, it is required to analysis of various factors in road traffic prediction models. This paper was studied the road traffic noise propagation factors such as distance from road to building, receiver height, alignment angle of building and reflection coefficient of the building facade by two calculation models, RLS-90 and CRTN. The result showed that noise reduction was generally higher at bottom stories by ground absorption effect. The reflection coefficient of the building facade was affect of additional sound pressure level by facade reflecting. And alignment angle of building at $90^{\circ}$ was performed effective noise reduction better than $0^{\circ}$.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 추계학술대회 논문집
• /
• pp.1042-1049
• /
• 2007

Recently, a theoretically-sound design approach, using an elastic multilayer model, is attempted in trackbed designs for the construction of high speed railways and new lines of conventional railways. In the elastic multilayer model, the stress-dependent resilient modulus($E_R$) is an important input parameter, that is, reflects substructure performance under repeated traffic loading. However, the evaluation method for resilient modulus using repeated loading triaxial test is not fully developed for practical purpose, because of costly equipment and the significantly fluctuated values depending on the testing equipment and laboratory personnel. In this study, the paper will present an indirect method to estimate the resilient modulus using dynamic properties. The resilient modulus of crushed stone, which is the typical material of sub-ballast, was calculated with the measured dynamic properties and the range of stress level of the sub-ballast, and approximated with the power model combined with bulk and deviatoric stresses. The resilient modulus of coarse grained material decreases with increasing deviatoric stress at a confining pressure, and increases with increasing bulk stress. Sandy soil(SM classified from Unified Soil Classification System) of subgrade was also evaluated and best fitted with the power model of deviatoric stress only.

• 한국소음진동공학회논문집
• /
• 제24권3호
• /
• pp.189-197
• /
• 2014

윗면에 개구부가 있는 쐐기 상자 모양으로 단순화 된 모델은 현대자동차에서 버페팅 현상을 구현하기 위해 사용되었다. 제안된 조건에서 수행한 측정값들은 버페팅 예측을 통해 CFD의 성능을 검증하기 위함이었다. PowerFLOW를 이용하여 얻어진 버페팅 해석 결과와 개구부가 없는 상태에서의 윗면의 경계층 발달을 이 논문에 기술하였다. 실험에서 측정된 음압은 유동 메커니즘을 통해 기술 하였고, 유동구조를 잘 묘사할 수 있도록 개선된 셋업을 통해 측정된 음압에 근사한 결과를 얻을 수 있었다.

• 한국음향학회지
• /
• 제19권4호
• /
• pp.107-114
• /
• 2000

기존의 Push-Pull 트랜스듀서보다 간단한 구조를 가지며 출력을 한층 더 높이기 위해서 실린더 중앙에 구동부를 둔 새로운 구조의 Push-Pull 트랜스듀서를 설계하고자 한다. 유한 요소 상용 패키지인 ANSYS를 이용하여 트랜스듀서 모델을 구성한 후, 각종 구조 변수들, 즉, 길이, 반경, Endcap Edge 형상등의 변화에 대한 음압의 변화경향을 조사하여 최대 음압을 구현하기 위한 최적 길이, 반경, Endcap Edge 형상을 설정하였다. 기존 트랜스듀서 보다 구조적으로 더 간단하면서도 더 큰 음압을 구현할 수 있는 새로운 구조의 고출력 트랜스듀서를 개발하였고, 그 성능을 기존 트랜스듀서의 성능과 비교 평가함으로써 개발된 트랜스듀서의 우수성을 입증하였다.

• 한국소음진동공학회논문집
• /
• 제20권9호
• /
• pp.797-804
• /
• 2010

In case of the construction equipment using by the military camp, such equipments are different from those equipments using at general construction site, of which muffler(silencer) is attached at the passenger seat side, since such equipments are obsoleted, it is great part that a considerably loud noises are continuously diffusing. When working, such noise can be influenced a lot of effects to those working soldiers nearby the equipment, and though it is really terrible loud noise as much as can arise a civil complaints by neighboring civilians, but because its specialty of the military, it is real state that there are many difficulties in establishing an effective soundproof countermeasure due to study shortage and lack of the relevant material regarding to military construction equipment. Accordingly, this study has ever grasped the characteristics of noise by its each frequencies and by distances about those 9 kinds of construction equipments using chiefly by the military camp. As the result, it was known that the military construction equipment is generating the loud noise which can influence bad effect to the workers, and such high sound pressure level of low frequency band can harm even to far distance.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.858-861
• /
• 2006

In this paper, a study on the noise reduction in a mobile fuel cell system is presented. Among various fuel cell systems around 20W capacities designed for mobile electronic devices, the active direct methanol fuel cell (DMFC) systems have been recently developed. In such systems, the primary noise source is the air pump which provides sufficient air flow ($5{\sim}6$ liter/min) for electrochemical reaction with methanol fuel while the noise contributions from other auxiliary parts are relatively small. Especially, the discrete noise tones generated by the air pump are dominant and those frequency peaks related to the rotor harmonics are needed to be suppressed by a silencer. Therefore. the Herschel/Quinke (HQ) tubes, which use the out-of-phase cancellation of acoustic waves propagating through direct and indirect pathways, are applied to the inlet of the air pump. Performance of noise reduction with HQ silencer is analytically estimated by calculating the transmission. The length and number of thin HQ tubes are optimized to decrease the radiated noise. As a result, the sound pressure level could be successfully reduced by about 10 dB after applying three serially connected HQ tubes.

• 정보저장시스템학회:학술대회논문집
• /
• 정보저장시스템학회 2005년도 추계학술대회 논문집
• /
• pp.197-202
• /
• 2005

Current Optical Disk drive is dominating high share gradually in information storage device market through development of great skill. These technologies can achieve not only improvement of transmission speed but also elevation of recording/reproduction technology. However, these present state cause not only the increase of vibration in structural viewpoint but also problem of serious noise while the ODD becomes high speed/high performance. Specially, air-born noise is being bigger than structural-born noise as disk rotation speed increases gradually. The object of this research is that reduce the air-born noise in optical disk drive by reducing a quantity of flow by using a miniaturized muffler. The micro muffler is a miniaturized muffler. The muffler is used widely by solution to reduce air-born noise which is generated by flow. According to frequency band of the noise source, it can be applied by muffler of various forms. In this research, we examined the noise characteristics of the micro muffler and applied it by noise reduction solution of the ODD. It could get an excellent noise reduction in high frequency band by using the micro muffler than the opened case through the decrease of an inner flow. But it could not get a noise reduction in low frequency band through the decrease of an inner flow.

• 음성과학
• /
• 제4권2호
• /
• pp.69-89
• /
• 1998

The aim of this study is to develop an objectively method of speech evaluation for children with cleft palates. To assess velopharyngeal function, Visi-Pitch, Computerized Speech Lab. (CSL), Nasometer and Palatometer were used for this study. Acoustic parameters were measured depending on the diagnostic instruments: Pitch (Hz), sound pressure level (dB), jitter (%) and diadochokinetic rate by Visi-Pitch, VOT and vowels formant ($F_1\;&\;F_2$) by a Spectrography and the degree of hypernasality by Nasometer. In addition, Palatometer was used to find the lingual-palatal patterns of cleft palate. Ten children with cleft palates and fifty normal children participated in the experiment. The results are as follows: (1) Higher nasalance of children with cleft palates showed the resonance disorder. (2) The cleft palate showed palatal misarticulation and lateral misarticulation on the palatogram. (3) Children with cleft palates showed the phonatory and respiratory problems. The duration of sustained vowels in children with cleft palates was shorter than in the control groups. The pitch of children with cleft palates was higher than in the control groups. However, intensity, jitter and diadochokinetic rate of children with cleft palates were lower than in the control group. (4) On the Spectrogram, the VOT of children with cleft palates was longer than control group. $F_1\;&\;F_2$ were lower than in the control group.

• 한국음향학회지
• /
• 제6권1호
• /
• pp.48-57
• /
• 1987

냉장고에 있어서 소음의 주발생원이 압축기라는 것은 잘 알려져 있는 사실이며 최근 제품의 경량화와 고급화 추세에 따라 그 영향이 더욱 증대되고 있다. 본 연구에서는 이러한 소음을 방지 또는 감소시키기 위하여 냉장고용 압축기에 대한 음압과 음향인텐시티를 측정하여 소음의 방사특성을 파악하였으며 이를 규명하기 위하여 실험적 모우드 해석법을 압축기 구조물에 대하여 적용하였다. 연구결과, 압축기 내부의 모우터 구동에 의해 발생한 진동이 스프링에 의해 효과적으로 절연되지 못하고 있으며 압축기의 shell과 mounting도 소음에 크게 기여하고 있음을 알았다.