• The Journal of the Acoustical Society of Korea
• /
• v.41 no.5
• /
• pp.481-491
• /
• 2022

The active sonar transmission system consists of a transmitter that outputs an electrical signal and an underwater acoustic transducer that converts the amplified electrical signal into an acoustic signal. In general, the transmitter output characteristics are dependent on load impedance, and an underwater acoustic transducer, which is a transmitter load, has a characteristic that the electrical impedance varies largely according to frequency when driven. In such a variable impedance condition, the output of the active sonar transmission system may become unstable. Hence, this paper proposes a design and control technique of a sonar transmitter for transmitting a stable transmission signal even under variable impedance conditions of an underwater acoustic transducer in an active sonar transmission system. The electrical impedance characteristics of the underwater acoustic transducer are experimentally analyzed, and the sonar transmitter is composed of a single-phase full-bridge inverter, an LC filter, and a matching circuit. In this paper, the design and output control method of the sonar transmitter is proposed to protect the transmitter and transducer. It can secure stable output voltage characteristics even if it transmits the Linear Frequency Modulation (LFM) signal. The validity is verified through the simulation and the experiment.

• Journal of Ocean Engineering and Technology
• /
• v.28 no.5
• /
• pp.440-451
• /
• 2014

A multi-static SONAR system consists of the transmitters and receivers separately in space. The active target echoes are received along the transmitter-target-receiver path and depend on the shape and aspect angle of the submerged objects at each receiver. Thus, the target echo algorithm used with a mono-static system, in which the transmitter and receiver are located at the same position, has limits in simulating the target echoes for a multi-static SONAR system. In this paper, a target echo modeling procedure for a 3D submerged object in space is described based on the Kirchhoff approximation, and the SONAR system is extended to a multi-static SONAR system. The scattered field from external structures is calculated on the visible surfaces, which is determined based on the locations of the transmitter and receiver. A series of experiments in an acoustic water tank was conducted to measure the target echoes from scaled targets with a single transmitter and 16 receivers. Finally, the numerical results were compared with experimental results and shown to be useful for simulating the target echoes/target strength in a multi-static SONAR system.

• The Journal of the Acoustical Society of Korea
• /
• v.31 no.5
• /
• pp.280-287
• /
• 2012

This paper presents a study on the experimental analysis of the impedance characteristics according to the rotational direction of the transmission beam of a cylindrical sensor array. Besides, this suggests a real time control technique of the transmitter output for the effective maximum power transmission, in order to drive efficiently the rotational transmission beam of the active sonar transmitter. The output characteristics of the transmitter and the real-time impedance variations of the sensor array are analyzed under the overload conditions. They are caused by electric and acoustic boundary conditions when the rotational transmission beam is operated. From these results, a new output control method of the transmitter is proposed to protect the transmitter and its loads. It can maximize the output power without the transmission pause even if the transient phenomena occur. The proposed technique is verified from the experiment.

• The Journal of the Acoustical Society of Korea
• /
• v.36 no.3
• /
• pp.202-210
• /
• 2017

For the target tracking in cluttered environment using a bistatic sonar whose transmitter and receiver are separately positioned, it is necessary to use data association algorithm via applying a proper measurement modelling to the bistatic sonar. The measurements obtained from the interval of ownship's maneuver have an increased error due to uncertainty of the position of transmitter and receiver. Using the measurements from this interval results in poor target tracking performance. In this paper, an improved tracking performance for the proposed data association based multiple model algorithm is validated by a monte carlo simulation.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.1E
• /
• pp.14-19
• /
• 1998

This article describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a sonar transducer. The sonar shell is simulated to be driven by electrical charges applied onto inner and outer surfaces of the shell. It is shown that at relatively low input frequency a beam pattern which is almost close to omnidirection can be obtained. The coupled FE-BE method is described in detail.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.1
• /
• pp.37-43
• /
• 1998

This article describes the application of a coupled finite element-boundary element method to obtain the steady-state response of a sonar transducer. The particular structure considered is a flooded piezoelectric spherical shell. The sonar shell is simulated to be driven by electrical charges applied onto inner and outer surfaces of the shell. It is shown that at relatively low input frequency a beam pattern which is almost close to omnidirection can be obtained. The coupled FE-BE method is described in detail.

• Journal of KSNVE
• /
• v.9 no.5
• /
• pp.1036-1041
• /
• 1999

This paper aims for the development of the high power sonar system for measuring the velocity of a moving object. The high power sonar system transmits two gated 190 kHz sinusoidal signals with 1.6 [ms] time interval to the moving object. Then the sonar system detects and calculates the changed time delay of the reflected ultrasonic signals in order to derive the velocity of the moving object. The transmission part uses a high power amplifier so that 250 W gated sinusoidal signals can be transmitted to the transmitter. 1M RAM is utilized for transmitting and storing of the ultrasonic signals. The time delay is calculted by the cross-correlation technique between the transmitted signals and the received signals. The measured value from the high power sonar system is compared with directly measured values by photo diodes. The result confirms the adjacency to 0.3% error.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.2
• /
• pp.158-165
• /
• 2018

Recently there is a great interest in the bi-static sonar. However, since the transmitter and the receiver operate on different platforms, it may be necessary to operate the system in a non-cooperative mode. In this situation, the detection and localization performance are limited. Therefore, it is necessary to classify the received pulse from the transmitter to overcome the performance limitation. In this paper, we proposed a robust automatic pulse classification method that can be applied to real systems. The proposed method eliminates the effects of noise and multipath propagation through post-processing and improves the pulse classification performance. We also verified the proposed method through the sea experimental data.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.3
• /
• pp.282-289
• /
• 2009

This paper presents an estimation technique of the equivalent circuit parameters for an underwater acoustic piezoelectric transducer from the measured impedance. Estimated equivalent circuit can be used for the design of the impedance matching network of the sonar transmitter. A fitness function is proposed to minimize the error between the calculated impedance of the equivalent circuit and the measured impedance of the transducer. The equivalent circuit parameters are estimated by using the fitness function and the PSO(Particle Swarm Optimization) algorithm. The effectiveness of the proposed method is verified by the applications to a sandwich-type transducer and a dummy load. In addition, the impedance matching network is also designed by using the estimated equivalent circuit model.

• Ocean Systems Engineering
• /
• v.13 no.2
• /
• pp.195-224
• /
• 2023

This paper proposes a method for the acoustic imaging wherein the traditional requirement of the relative movement between the transmitter and target is overcome. This is facilitated through the beamforming acoustic array in the transmitter, in which the target is illuminated by the array at various azimuth and elevation angles without the physical movement of the acoustic array. The concept of beam steering of the acoustic array facilitates the formation of the beam at desired angular positions of azimuth and elevation angles. This paper substantiates that the combination of illumination of the target from different azimuth and elevation angles with respect to the transmitter (through the beam steering of beam forming acoustic array) and the beam steering at multiple frequencies (through SF) results in enhanced reconstruction of images of the target in the underwater scenario. This paper also demonstrates the possibility of reconstruction of the image of a target in underwater without invoking the traditional algorithms of Digital Image Processing (DIP). This paper comprehensively and succinctly presents all the empirical formulae required for modelling the acoustic medium and the target to facilitate the reader with a comprehensive summary document incorporating the various parameters of multi-disciplinary nature.