• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.928-931
• /
• 2008

Using 4,4'4"-tris(N-carbazolyl)-triphenylamine (TCTA) small molecule interlayer, we have fabricated efficient green PHOLED by solution process. The maximum current and power efficiency values of 33.7 cd/A and 19.6 lm/W are demonstrated, respectively. Results reveal a way to fabricate the PHOLED using TCTA interlayer by solution process, promising for efficient and simple manufacturing.

• 한국세라믹학회지
• /
• 제39권12호
• /
• pp.1177-1182
• /
• 2002

인산염 용액과의 반응으로 패각의 표면에 고 비표면적의 다공성 수산화아파타이트 층이 생성되는 거동을 정성적으로 관찰하였다. 수산화아파타이트의 생성기구는 패각 표면을 핵으로하는 용해-석출 반응으로 보이며 층의 생성은 다음의 과정에 의하였다. 1. 고상 표면 상의 고밀도 핵생성 및 성장 2. 결정의 접촉과 엉킴에 의한 미세 다공성 층의 형성 3. 층을 통한 용액의 확산과 내측으로의 층 두께의 성장

• 설비공학논문집
• /
• 제12권2호
• /
• pp.218-225
• /
• 2000

In the present study, the effects of film Reynolds number (60∼200) and volumetric content of non-absorbable gases (0∼10%) in water vapor on the absorption process of aqueous LiBr solution were investigated experimentally. The formation of solution film on the horizontal tubes of six rows were observed to be complete for Re>100. Transition film Reynolds number were found to exist above which the Nusselt number and Schmidt number diminishes with solution flow rate. As the concentration of non-absorbable gases increased, mass transfer rate decreased more seriously than heat transfer rate did. The degradation effects of non-absorbable gases seemed to be significant especially when small amount of non-absorbable gases were introduced to the pure water vapor.

• 대한안전경영과학회지
• /
• 제14권1호
• /
• pp.167-177
• /
• 2012

In this paper, we raised the performance of heuristic algorithm to assign job to workers in parallel line inspection process without sequence. In previous research, we developed the heuristic algorithm. But the heuristic algorithm can't find optimal solution perfectly. In order to solve this problem, we proposed new method to make initial solution called FN(First Next) method and combined the new FN method and old FE method using previous heuristic algorithm. Experiments of assigning job are performed to evaluate performance of this FE+FN heuristic algorithm. The result shows that the FE+FN heuristic algorithm can find the optimal solution to assign job to workers evenly in many type of cases. Especially, in case there are optimal solutions, this heuristic algorithm can find the optimal solution perfectly.

• 동력기계공학회지
• /
• 제18권4호
• /
• pp.72-77
• /
• 2014

The aim of this study to investigate polarization characteristics of WC-based alloy coatings fabricated by high velocity oxygen fuel(HVOF) process. The coatings were fabricated by HVOF process with WC-CrC-Ni, WC-Co-Cr, WC-Co composite powders. Corrosion tests were carried out using potentiostat/galvanostat at solution with pH 2 and pH 6. Corrosion potential(Ecorr) and corrosion current density(Icorr) could be analyzed from polarization curve. WC-Co-Cr coating showed more incorrodible characteristics than other coatings at solution pH 2. WC-CrC-Ni coating was more favorable anti-corrosion characteristics than other coatings at solution with pH 6.

• Journal of Industrial and Engineering Chemistry
• /
• 제67권
• /
• pp.407-416
• /
• 2018

This study presents a novel complete solution starting with a synthesis of silica modified with potassium-nickel hexacyanoferrate and ethanolamine (SiEA-KNiFe) sorbent through radiocesium sorption in different process configurations and moving on to the vitrification of the spent sorbent, using the sol-gel method. The experimental data for deionized water solution, as well as seawater solution, correlates strongly with the Langmuir isotherm model. Moreover, the study also presents a method for spent sorbent solidification in the glass matrix. The cesium leaching test confirmed that spent sorbent can be stably bound in the glass matrix after radionuclide removal.

• 한국농공학회논문집
• /
• 제55권2호
• /
• pp.21-27
• /
• 2013

The present study explored the way to desalinate seawater for agricultural irrigation using forward osmosis (FO) process using liquid fertilizer as draw solution. FO experiments were performed in a cross flow mode using flat sheet FO membrane. The effect of membrane orientation, flow rate, and draw solution concentration on the performance of forward osmosis was investigated by measuring water flux of forward osmosis membrane. The water flux when the draw solution was placed against the membrane active layer was lower than the water flux when the feed solution was placed against the membrane active layer. This results indicated that the decrease of effective osmotic pressure by dilutive internal concentration polarization was less than that by concentrative internal concentration polarization. Increasing flow rate from 66.7 to 133.1 $cm^3$/min resulted in increase of the water flux when the membrane active layer orient to draw solution and feed solution, respectively. The reduction of resistance to water flow increased water flux at higher flow rate. The water flux of FO membrane increased with increasing draw solution concentration from 10000 to 30000 mg/L. The water flux for $KH_2PO_4$ draw solution was similar to that for commercial fertilizer. Optimization of FO process would contribute to economically desalinate brackish water for agricultural use.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.390-397
• /
• 1998

An approach to identifying input forces is proposed using measured structural dynamic responses and its analytical model. The identification of input forces is a reverse process and ill-conditioned problem. Its solution is unstable and generally case dependent. In this paper, the ill-condition is described considering characteristic matrix which is defined by reduced dynamic stiffness matrix. Special attention is focused on the condition number of a characteristic matrix used in the solution algorithm of this reverse process. Simple example is presented in support of the ill-condition of a reverse process.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2008년도 춘계학술대회
• /
• pp.345-360
• /
• 2008

The analytic hierarchy process is known as a useful tool for the group decision making methods. This tool has been area such as investment, R&D management, manufacturing, production and marketing. Typically, transportation problems have addressed by mathematical programming. In this paper, an optimal solution of transportation problem was determined by the analytic hierarchy process.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 The 6th International Symposium of East Asian Resources Recycling Technology
• /
• pp.165-170
• /
• 2001

The main purpose of this study is to generate a fine copper oxide powder of high purity, with a compact structure and a uniform particle size by a spray pyrolysis process. The raw material is a waste copper chloride solution formed in the manufacturing process of Print Circuit Board (PCB). This study also examines the influences of various factors on the properties of the generated powder. These factors include the reaction temperature, the inflow speed of the raw material solution, the inflow speed of the air, the size of the nozzle tip, and the concentration of the raw material solution. It is discovered that, as the reaction temperature increases from 80$0^{\circ}C$ to 100$0^{\circ}C$ , the particle size of the generated powder increases accordingly, and that the structure of the powder becomes much more compact. When the reaction temperature is 100$0^{\circ}C$, the particle size of the generated powder increases as the concentration of copper in the raw material solution increases to 40g/l, decreases as the concentration increases up to 120g/l, and increases again as the concentration reaches 200g/1. In the case of a lower concentration of the raw material solution, the generated powder appears largely in the form of CuO. As the concentration increases, however, the powder appears largely in the form of CuCl. When the concentration of copper in the raw material solution is 120g/1, the particle size of the generated powder increases as the inflow speed of the raw material solution increases. When the concentration of copper in the raw material solution is 120g/1, there is no evident change in the particle size of the generated powder as the size of the nozzle tip and the air pressure increases. When the concentration is 40g/1, however, the particle size keeps increasing until the air pressure increases to 0.5kg/$\textrm{cm}^2$, but decreases remarkably as the air pressure exceeds 0.5kg/$\textrm{cm}^2$.