• 전자공학회논문지
• /
• 제51권10호
• /
• pp.197-203
• /
• 2014

신관 안전장전장치는 비행체의 수송, 저장, 취급 중의 안전을 절대적으로 보장하도록 설계되어야 한다. 본 논문에서는 비행체에 적용되는 신관 안전장전장치의 안전성을 증대시키기 위한 솔레노이드 조립체와 솔레노이드 조립체를 구동하기 위한 솔레노이드 구동회로를 포함한 신관 안전장전장치 설계에 대해 기술한다. 솔레노이드 조립체는 신관 안전장전장치에 적용한 추가적인 안전장치로서, 코일 조립체, 복원스프링, 코어 등으로 구성된다. 솔레노이드 조립체의 코어는 평상시에는 1차 안전장치를 구속하고 있어 1차 안전장치가 작동하는 것을 저지해줌으로써 비행체의 취급이나 수송 시 안전을 확보해주게 되며, 발사를 위한 비행체 배터리 전원이 인가 및 활성화되어 신관 안전장전장치에 공급되면, 솔레노이드 구동회로가 코어를 작동시켜 신관 안전장전장치의 1차 및 2차 안전장치를 해제시키는 역할을 한다. 또한, 솔레노이드 구동회로는 비행체 발사 이후, 신관 안전장전장치의 기계적 장전이 완료되어 장전스위치가 turn-on되면 솔레노이드 조립체에 인가되는 전원을 자동 차단시켜 비행 중의 전원 소모량을 줄일 수 있도록 하였다.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제2권2호
• /
• pp.239-245
• /
• 2013

Modern electric controlled valves are demanded that its solenoid actuator should be smaller size, lighter weight, lower consumption power, and higher response time. For achieving these purposes, the major design factors of solenoid actuator such as magnetic flux density, coil turn numbers, plunger size, bobbin dimension, and etc. are must be optimized. In this study, for optimal design of high speed solenoid actuator for hydraulic servo valve operation, we draw up governing equations which are composed by combination of electromagnetic theories and empirical knowledge, and deduct the values of major design factors by use of them. For more increase the operating speed, voice coil are used as main armature in manufacturing of prototype actuator. And, we have proven the propriety of the governing equations and speed increasing method by experiments using the hydraulic valve assembly adopted the prototype of solenoid actuator.

• 동력기계공학회지
• /
• 제12권2호
• /
• pp.62-70
• /
• 2008

The paper made a description of the method for numerical analysis and modeling of a proportional pressure control valve by bondgraph. The valve is a three port pressure regulator valve, consists of two subsystems; a proportional solenoid and a spool assembly. A purpose of this study is to analysis the dynamic characteristics of the valve using bondgraph method and to verified results that each of parameters has an effect on modeling. It considered the effect which the presence of solenoid, flow coefficient and non-linearity of resistance causes in the valve modeling. In particular, it is analyzed the effect that the solenoid interacted with modeling results and characteristics of the nonlinear resistance through orifice on the supply and discharge side of valve. Thus this paper described method to present nonlinear characteristics by bondgraph modeling method, so that we could know easily result that each parameters has an effect on the modeling.

• 한국공작기계학회논문집
• /
• 제14권5호
• /
• pp.87-92
• /
• 2005

In this study, an automation assembly jig for the automation assembly process for the ventilation grille that is used in the interior of a car Is developed. As the method that can do the automation assembly for the ventilation grille, a simple jig and air cylinder have been applied. And a solenoid valve, a filter regulator, and on-off switch have been used in controlling the system. Moreover, the timer is attached to the equipment so that a worker may control the assembly time, as fitting the quantity on demand of production. Actually with executing the assembly test productivity and performance of assembly have been verified. In case of the automation assembly work for a ventilation grille is compared to the manual work. The optimum working speed has been identified to make the process twice or three times better.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.77-82
• /
• 2000

In this study, an automation assembly jig for the automation assembly process for the ventilation grille that is used in the interior of a car is developed. As the method that can do the automation assembly for the ventilation grille, a simple jig and air cylinder have been applied. And a solenoid valve, a filter regulator, and on-off switch have been used in controlling the system. Moreover, the timer is attached to the equipment so that a worker may control the assembly time, as fitting the quantity on demand of production. Actually with executing the assembly test productivity and performance of assembly have been verified. In case of the automation assembly work for a ventilation grille is compared to the manual work. The optimum working speed has been identified to make the process twice or three times better.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2001년도 학술대회 논문집
• /
• pp.121-124
• /
• 2001

The research results on the superconducting magnet for whole body MRI are presented. The magnet consists of main coil with 6 solenoid coils, shielding coil with 2 solenoid coils and 6 sets of cryogenic shim coil. The ferromagnetic shim assembly is installed on the inside wall of the room temperature bore for shimming inhomogeneous field components generated due to manufacturing tolerances, installation misalignments and external ferromagnetic materials near the magnet. Also, the magnet is enclosed with the horizontal type cryostat with 80cm room temperature bore to keep the magnet under the operating temperature. The magnetic field distributions within the imaging volume were measured by the NMR field mapping system. Through the test, the central field of magnet was 1.5 Tesla and the field homogeneity of 9.3 ppm has been obtained on 40cm DSV(the diameter of spherical volume) and using this magnet, comparatively good images for human body, fruits and water phantoms have been achieved.

• 대한기계학회논문집A
• /
• 제35권10호
• /
• pp.1307-1313
• /
• 2011

전자제어식 차동제한 장치는 기계식에 비해서 능동제어가 가능하고 응답성이 좋아 기계식을 대체해 나가고 있다. STS 304 재질의 코일 하우징은 전자제어식 차동제한장치의 솔레노이드 어셈블리에서 가장 중요한 부품이다. 코일 하우징의 제조시 높은 형상 정밀도가 필수적이나, STS 304의 박판 사용과 가공변수의 변동으로 정밀 가공이 어렵다. 본 연구의 목적은 코일하우징의 가공조건에서 강건해를 구하여 평균과 변동을 최적화 하는 것이다. 코일하우징의 형상정밀도 평균과 표준편차를 최소화 하기 위한 주요 변수로 조의 척킹압력, 절삭속도, 이송속도의 평균과 표준편차가 고려됐다. 가공변수의 변동을 고려하여 평균과 표준편차를 모두 최소화 하는 최적의 조건을 선정하고자 반응표면모델 기반 2차 테일러 전개를 통한 강건 최적설계를 수행하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.22-25
• /
• 2001

The research results on the superconducting magnet for whole body MRI are presented. The magnet consists of main coil with 6 solenoid coils, shielding coil with 2 solenoid coils and 6 sets of cryogenic shim coil. The ferromagnetic shim assembly is installed on the inside wall of the room temperature bore for shimming inhomogeneous field components generated due to manufacturing tolerances, installation misalignments and external ferromagnetic materials near the magnet. Also, the magnet is enclosed with the horizontal type cryostat with 80cm room temperature bore to keep the magnet under the operating temperature. The magnetic field distributions within the imaging volume were measured by the NMR field mapping system. Through the test, the central field of magnet was 1.5 Tesla and the field homogeneity of 9.3 ppm has been obtained on 40cm DSV(the diameter of spherical volume) and using this magnet, comparatively good images for human body, fruits and water phantoms have been achieved.

• 한국가스학회지
• /
• 제15권3호
• /
• pp.47-52
• /
• 2011

이 논문의 목적은 LPG 자동차의 전자제어에 대한 요소의 하나인 액추에이터에 대한 고장사례를 찾아 분석하고 연구하는 것이다. 차량의 연료를 저장하는 봄 내부의 LPG 긴급 차단 솔레노이드 밸브의 필터가 막혀 연료의 공급이 간헐적으로 차단되는 현상이 발생되어 엔진이 작동하는 동안 엔진의 초기시동불량이나 가속이 되지 않는 것을 확인하였다. 엔진 컨트럴 릴레이 부위의 접점부가 가공불량이나 조립불량에 의해 완전한 면접촉이 되지않아 접촉저항이 발생되어 초기 시동을 걸었을 때 시동이 걸렸으나 재시동을 걸 때 시동이 걸리지 않는 현상을 확인하였다. 공회전 조절장치의 내부에 카본이 퇴적되어 액추에이터가 고착되어 흡입공기의 공급이 감소되어 자동차의 시동이 걸려 공회전 상태일 때 엔진의 회전수가 규정 범위를 벗어나 상승과 하락을 반복하는 불안정 상태를 확인하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.559-562
• /
• 1999

In this paper, we developed on internet based assembly information display system for the blind. The system is consist of hardware and software. The hardware is consist of a voice synthesis device and a tactile display for character information, and the software is consist of internet web browser for the blind and braille program. The tactile-device system consists of a control unit, pin array, pin generator, serial port, and a power supply. The pin exerted by a electromagnetic method, solenoid. The internet web browser separates the character and image from internet web page, and character information in the web page is converted to braille and fed to sound system. Also the image in the web page can be printed developed tactile display. As the results of experiment, the blind could access the internet web site by using this system and understand various internet information.