• Current Photovoltaic Research
• /
• 제8권1호
• /
• pp.6-11
• /
• 2020

The power conversion efficiency (PCE) of a two-terminal tandem solar cell depends upon the tunnel-recombination junction (TRJ) between the top and bottom sub-cells. An optimized TRJ in a tandem cell helps improve its open-circuit voltage (V_oc), short-circuit current density (J_sc), fill factor (FF), and efficiency (PCE). One of the parameters that affect the TRJ is the buffer layer thickness. Therefore, we investigated various TRJs by varying the thickness of the buffer or intermediate layer (TRJ-buffer) in between the highly doped p-type and n-type layers of the TRJ. The TRJ-buffer layer was p-type nc-Si:H, with a doping of 0.06%, an activation energy (E_a) of 43 meV, an optical gap (E_g) of 2.04 eV, and its thickness was varied from 0 nm to 125 nm. The tandem solar cells we investigated were a combination of a heterojunction with intrinsic thin layer (HIT) bottom sub-cell and an a-Si:H (amorphous silicon) top sub-cell. The initial cell efficiency without the TRJ buffer was 7.65% while with an optimized buffer layer, its efficiency improved to 11.74%, i.e., an improvement in efficiency by a factor of 1.53.

• 한국전기전자재료학회논문지
• /
• 제37권2호
• /
• pp.182-187
• /
• 2024

Currently, the most developed new energy source is solar energy. Because solar power is installed outside, it is exposed to many pollutants. Pollutants are causing the characteristics of solar energy to deteriorate. Therefore, this study aims to develop a water-repellent coating to prevent contamination of solar modules. Silica and Titania materials are mainly used as water-repellent coating materials. In this study, it was based on silica and the contact angle characteristics were measured according to the change in the amount of silica and ammonia water added and the number of coatings. As a result of the measurement, it was confirmed that the contact angle was more than 60 degrees when 0.5 mol of TEOS was added to 50 mL and 0.15 M when 1 mL of ammonia water was added to 296.47 ml of distilled water. And it was confirmed that the contact angle improved when the number of coatings was applied twice. A water-repellent coating material was applied to low iron tempered glass used to protect dye-sensitized solar cell modules. The characteristics of the module were measured after spraying DI-Water on low-emission tempered glass with a water-repellent coating. As a result of the measurement, the efficiency of the module without application, the efficiency of the module coated once, and the module coated twice were 4.87%, 4.90%, and 4.91%, respectively. It was confirmed that the efficiency of the module increased by applying water-repellent coating. As a result of this study, it is determined that the water-repellent coating material will help improve solar power generation efficiency and lifespan by being self-cleaning and non-reflective.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.287.2-287.2
• /
• 2016

Silicon has considerably good characteristics on electron, hole mobility and its price. With 2-D sinlge-layer Graphene/n-Si heterojunction solar cell shows that in one sun condition exhibit power conversion efficiency(PCE) of 10.1%. This photovoltaic effect was achieved by applying gate voltage to the Schottky junction of the heterostructure solar cell. Energy band diagram shows that Schottky barrier between Si and graphene can be adjust by the external electric field. because of the fermi level of the graphene can be changed by external gate voltage, we can control the Schottkky barrier of the heterostructure solar cell. The ratio between generated power of solar cell and consumption electrical power is remarkable. Since we use the graphene as the top gate electrode, most of the sun light can penetrate into the active area.

• 한국에너지공학회:학술대회논문집
• /
• 한국태양에너지학회, 한국에너지공학회 1993년도 춘계 공동학술발표회 초록집
• /
• pp.53-59
• /
• 1993

The interests on GaAs solar cell grown on Ge substrates as an alternative of GaAs substrate arises from its very close lattice parameters, very small difference in thermal expansion coefficients, and much higher fracture toughness between GaAs and Ge. In addition, for many space power application, it would be a most attractive solar cell with high radiation resistance of GaAs and high reliability for the reverse current damage of Ge, and expecting the theoretical efficiency limit of the tandem GaAs/Ge solar cell is 34% under 1 Sun, AM 0, and 28$^{\circ}C$ condition. In this report, we have reviewed the performance and the manufacturing technics of GaAs/Ge solar cell, and current status of research in GaAs/Ge solar cell.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권4호
• /
• pp.187-191
• /
• 2004

In this work, we used the PCID simulator for simulation of solar cell and examined the effect of front-back surface recombination velocity, minority carrier diffusion length, junction depth and emitter sheet-resistance. As the effect of base thickness, the efficiency decreased by the increase in series resistance with the increase of the thickness and found decrease in efficiency by decrease of the current as the effect of the recombination. Also, as the effect of base resistivity, the efficiency increased somewhat with the decrease in resistivity, but when the resistivity exceeded certain value, the efficiency decreased as a increase in the recombination ratio. The optimum efficiency was obtained at the resistivity 0.5 $\Omega$-cm, and thickness $100\mu\textrm{m}$. We have successfully achieved 10.8% and 13.7% efficiency large area($103mm{\times}103mm$) mono-crystalline silicon solar cells without and with PECVD silicon nitride antireflection coating.

• 반도체디스플레이기술학회지
• /
• 제14권4호
• /
• pp.45-49
• /
• 2015

Using a combined CVD and ALD equipment system, multi-layer quantum well structures of $Al_2O_3/a-Si/Al_2O_3$ were fabricated on silicon Schottky junction devices and implemented to quantum well solar cells, in which the 1~1.5 nm thicknesses of the aluminum oxide films and the a-Si thin film layers were deposited at $300^{\circ}C$ and $450^{\circ}C$, respectively. Fabricated solar cell was operated by tunneling phenomena through the inserted quantum well structure being generated electrons on the silicon surface. Efficiency of the fabricated solar cell inserted with multi-quantum well of 41 layers has been increased by about 10 times that of the solar cell of pure Schottky junction solar cell.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.330-332
• /
• 2006

In this paper, sun tracking system using Sun position sensor is proposed, the sun tracking system designed as which raises the efficiency of solar power generation. It design the structure being simple and it develops the system which is economical efficiency. It develops the hazard technique such as location tracking method of the sun which uses the sensor and to use the motor solar cell module movement. The Sun tracking system makes the drive in order to do with one axis and to use the sensor and to know in order to put out, the location of the sun and it makes. To make the solar location tracking sensor where the structure is simple it used two solar cells.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.36-36
• /
• 2010

Currently, there are several newly developed energy resources for the future to replace petroleum resources such as hydrogen fuel cell, solar cell, wind power, and etc. Among them, solar cell has attracted a worldwide concern, because it has an enormous amount of resources. In general, a study of solar cells can be classified in to an area of bulk type and thin-film type. Inorganic solar cells based on silicon have been tremendously developed in technology and efficiency. However, since there are many lithographic steps, high processing temperature approximately $1000^{\circ}C$, and expensive raw materials, a manufacturing cost of device are nearly reaching a limit. Contrary to those disadvantages, organic solar cells can be manufactured at room temperature. Also, it has many advantages such as a low cost, easy fabrication of thin film, and possible manufacture to a large size. Because it can be made to be flexible, research and development on solar cells are actively in progress for the next generation. ever though an efficiency of the organic solar cell is low compared to that of inorganic one, a continuous study is needed. In this paper, we report optimal device structure obtained by a program simulation for design and development of highly efficient organic photovoltaic cells. we have also compared simulated results to experimental ones.

• 한국전기전자재료학회논문지
• /
• 제31권5호
• /
• pp.295-299
• /
• 2018

In this work, we conducted a study on cell strings of high efficiency and high power solar cell modules via simulation. In contrast to the conventional module manufacturing method, the simulation was performed by connecting cutting cells divided into four parts from 6-in size using the electrically conductive adhesive (ECA). The resistance of the ECA added in series connection was extracted using an experimental method. This resistance was found to be $3m{\Omega}$. Based on this simulation, we verified the change in efficiency of the string as a function of the number of cutting cell connections. Consequently, the cutting cell efficiency of the first 20.08% was significantly increased to 20.63% until the fifth connection; however, for further connections, it was confirmed that the efficiency was saturated to 20.8%. Connecting cutting cells using ECA improves the efficiency of the string; therefore, it is expected that it will be possible to fabricate modules with high efficiency and high power.

• 반도체디스플레이기술학회지
• /
• 제13권3호
• /
• pp.21-25
• /
• 2014

The texturing is one of the most important processes for high efficiency crystalline silicon solar cells. The rear side flatness of silicon solar cell is very important for increasing the light reflectance and forming uniform back surface field(BSF) region in manufacturing high efficiency crystalline silicon solar cells. We investigated texturing difference between front and rear side of wafer by texturing of two adhered wafers. As a result, the flatter rear side was obtained by forming less pyramid size compared to the front side and improved reflectance of long wavelength and back surface field(BSF) region were also achieved. Therefore, the texturing of two adhered wafers can be expected to improve the efficiency of silicon solar cells due to increased short circuit current(Isc).