• 한국세라믹학회지
• /
• 제46권1호
• /
• pp.41-46
• /
• 2009

The rheological properties of highly concentrated Ag nano sol depending on particle size were studied. The Ag nano sol was prepared by reducing the Ag ion in aqueous solution. The size of Ag nano particle was controlled by two steps of nucleation and growth, and the thickness of adsorption layer was varied by molecular weight of polyelectrolytes. The polyelectrolytes acted as not only ionic complex agent in ionic state and but also dispersant after formation of Ag nano sol. The effective volume was controlled by combination of varying the molecular weight of polyelectrolytes and the size Ag nano sol. The particle size and the viscosity of nano sol were characterized by particle size analyzer, HR-TEM and cone & plate viscometer. It was found that the 10 nm and 40 nm-sized Ag nano sols were prepared by controlling the nucleation and growth steps, respectively. Finally, we could prepare highly concentrated Ag nano sol over 50 wt%.

• 한국세라믹학회지
• /
• 제31권8호
• /
• pp.911-919
• /
• 1994

As the study for preparation of single-layer anti-reflective coating on glass, the conditions of synthesis of sol for coating and of reproducible coating procedure were investigated. In case of water-based sol, coating was impossible because of poor wettability of sol. The Substitution of solvent with ethanol improved the wettability of sol on the glass surface, and optimum amount of ethanol for substitution was 70 vol%. Maximum specific surface area and total pore volume of water-based sol were 268.7$m^2$/g and 0.315 cc/g, but after substitution, those values increased to 404.1 $m^2$/g and 0.376 cc/g, respectively. The upper limit withdrawl speed of coating in order to get clean coated films without aggregations or stains was 7 cm/min. In case of addition of 0.1 mol HNO3 and substitution with 70 vol% ethanol and heat-treatment at 40$0^{\circ}C$ for 1 hour, thin film with thickness of 94 nm was obtained at withdrawl speed of 4 cm/min. The thickness of thin film was independent of drying time.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제11권4호
• /
• pp.277-281
• /
• 2006

Spherical micro silica sol-gel immobilized enzyme beads were prepared in an emulsion system using cyclohexanone and Triton-X 114. The beads were used for the in situ immobilization of transaminase, trypsin, and lipase. Immobilization during the sol to gel phase transition was investigated to determine the effect of the emulsifying solvents, surfactants, and mixing process on the formation of spherical micro sol-gel enzyme beads and their catalytic activity. The different combinations of sol-gel precursors affected both activity and the stability of the enzymes, which suggests that each enzyme has a unique preference for the silica gel matrix dependent upon the characteristics of the precursors. The resulting enzyme-entrapped micronsized beads were characterized and utilized for several enzyme reaction cycles. These results indicated improved stability compared to the conventional crushed form silica sol-gel immobilized enzyme systems.

• 한국대기환경학회지
• /
• 제19권1호
• /
• pp.57-66
• /
• 2003

TiO$_2$ sol was prepared by sol-gel method, and this sol was coated in ceramic and glass bead by dip-coating method. The coated catalyst was applied to degrade benzene in the gas phase by exposing to UV -lamp (365 nm) in a batch reactor. The removal efficiency of the benzene was compared by changing various conditions such as the kind of chemical additives, the coating beads (ceramic and glass), solution pH, the initial concentration of TiO$_2$ sol, UV intensity, and benzene concentration. The physical structure of TiO$_2$ sol used in this study was found to be pu-rely anatase type from XRD analysis. The results showed that ceramic bead was effective as the coating agent rath-er than glass bead. The significant change in the benzene removal efficiency of benzene did not occur with chang-ing coating frequency and the initial concentration of TiO$_2$ sol. The removal efficiency of benzene increased with increasing UV intensity, and with acidic treatment of TiO$_2$-coated ceramic bead.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.II
• /
• pp.1552-1555
• /
• 2005

We have studied the inkjet patterning of synthesized aqueous silver nano-sol on interface-controlled ITO glass substrate. Furthermore, we designed the conductive ink for direct inkjet patterning on bare ITO glass substrate. The first, the highly concentrated polymeric dispersant-assisted silver nano sol was prepared by variation of molecular weight and control of initial nucleation and growth of silver nanoparticles. The high concentration of batch-synthesized silver nano sol was possible to 40 wt%. At the same time the particle size of silver nanoparticles was below $10{\sim}20nm$. The second, the synthesized silver nano sol was inkjet - patterned on ITO glass substrate. The connectivity and width of fine line depended largely on the wettability of silver nano sol on ITO glass substrate, which was controlled by surfactant. The relationship was understood by wetting angle. The fine line of silver electrode as fine as $50{\sim}100\;{\mu}m$ was successfully formed on ITO glass substrate. The last, the direct inkjet-patternable silver nano sol on bare ITO glass substrate was designed also.

• 한국세라믹학회지
• /
• 제32권7호
• /
• pp.783-792
• /
• 1995

Sol-Gel derived ferroelectric PZT thin films were fabricated on ITO/Glass and Si/SiO2 substrates. In order to investigate the effect of catalysts on the densification and crystallization of PZT thin films, a nitric acid or ammonium hydroxide was added to the PZT stock solution at the state of partial hydrolysis reaction. The measured pH for a stable PZT sol was 5.2~9.3. In case of an acid-catalyzed PZT sol, a highly condensed particulate PZT sol was formed by accelerating the hydrolysis reaction. But weakly branched polymeric PZT sol was formed with a base-catalyzed condition. The difference in densification behavior was not found in the pH range of added catalyst, but the refractive index of PZT thin film was increased rapidly as the annealing temperature increased. The PZT thin film annealed at 54$0^{\circ}C$ for 10 min was fully densified and its refractive index was above 2.4. When the annealing temperature increased, the transition from the pyrochlore phase to perovskite appeared at 54$0^{\circ}C$. The base-catalyzed PZT thin film suppressed to form the pyrochlore phase and proceeded effectively to convert the perovskite phase. This was due to the formation of polymeric molecular structure by controlling the hydrolysis and condensation reaction through the additiion of the ammonium hydroxide.

• Bulletin of the Korean Chemical Society
• /
• 제30권10호
• /
• pp.2365-2370
• /
• 2009

A working electrode in dye-sensitized solar cells was fabricated using $TiO_2$ colloidal sol prepared from titanium isopropoxide used as a starting material by applying the sol-gel method. The effect of aging times and temperatures on physical and chemical properties of $TiO_2$ sol particles was systematically investigated. Results showed that the crystallinity and average particle size of $TiO_2$ colloidal sol can be successfully controlled by the adjustment of aging time and temperature. The conversion efficiency of the repetitive dry coating films fabricated using the dried $TiO_2$ colloidal sol particles and hydroxypropyl cellulose binder (15%) was 10.31% with a high transparency.

• 센서학회지
• /
• 제28권5호
• /
• pp.329-333
• /
• 2019

Solution-processed oxide thin-film transistors (TFTs) have garnered great attention, owing to their many advantages, such as low-cost, large area available for fabrication, mechanical flexibility, and optical transparency. Negative bias stress (NBS)-induced instability of sol-gel IGZO TFTs is one of the biggest concerns arising in practical applications. Thus, understanding the bias stress effect on the electrical properties of sol-gel IGZO TFTs and proposing an effective recovery method for negative bias stressed TFTs is required. In this study, we investigated the variation of transfer characteristics and the corresponding electrical parameters of sol-gel IGZO TFTs caused by NBS and positive bias recovery (PBR). Furthermore, we proposed an effective PBR method for the recovery of negative bias stressed sol-gel IGZO TFTs. The threshold voltage and field-effect mobility were affected by NBS and PBR, while current on/off ratio and sub-threshold swing were not significantly affected. The transfer characteristic of negative bias stressed IGZO TFTs increased in the positive direction after applying PBR with a negative drain voltage, compared to PBR with a positive drain voltage or a drain voltage of 0 V. These results are expected to contribute to the reduction of recovery time of negative bias stressed sol-gel IGZO TFTs.

• 대한치과교정학회지
• /
• 제36권6호
• /
• pp.451-464
• /
• 2006

본 연구는 항 교정장치의 개발에 도움이 되고자 이산화티탄 광촉매의 코팅 시 안정적이고 효과적인 방법을 찾기 위하여 시행되었다. 시판되고 있는 교정용 와이어와 브라켓에 sol-gel법, CVD (Chemical Vapor Deposition)법 및 PE-CVD (Plasma Enhanced-CVD)법으로 이산화티탄을 각각 코팅한 다음 각 방법으로 코팅된 이산화티탄 박막의 특성을 알아보고자 주사전자현미경을 이용하여 각 시편의 코팅박막 표면의 거칠기를 관찰하였고 adhesive tape pull test를 이용하여 코팅박막의 접착강도를 측정하였다. 메틸렌블루용액에 각 시편을 침지시킨 후 시간경과에 따른 메틸렌블루용액의 농도변화 측정을 통해 코팅박막의 분해능을 평가하였으며 불화나트륨 용액에 각 시편을 침지시킨 후 주사전자현미경을 이용하여 표면부식 정도를 관찰함으로써 불소화합물에 대한 내부식성을 평가하여 다음과 같은 결과를 얻었다. 코팅박막의 표면은 CVD법 및 PE-CVD법이 sol-gel법이나 코팅되지 않은 시편에 비해 더 매끄러웠다. 코팅박막의 접착강도는 PE-CVD법이 가장 높았고, CVD법, sol-gel법의 순으로 낮게 나타났다. 코팅박막의 메틸렌블루 분해능은 PE-CVD법이 가장 높았고, CVD법, sol-gel법의 순으로 낮게 나타났다. 코팅박막의 불소화합물에 대한 내부식성은 CVD법 및 PE-CVD법이 sol-gel법에 비해 높게 나타났다. 이상의 결과는 교정용 와이어 및 브라켓의 이산화티탄 광촉매 코팅 시 CVD법 및 PE-CVD법이 sol-gel법보다 적절한 방법임을 시사하였다.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2006년도 한국우주과학회보 제15권1호
• /
• pp.38-38
• /
• 2006