• Korean Journal of Environmental Biology
• /
• v.17 no.2
• /
• pp.191-198
• /
• 1999

Enzyme-aided bleaching of softwood and hardwood kraft pulps by a xylanase preparation from an alkalophilic fungus Cephalospotium sp. RYM-202 was studied. Maximal solubilization of Pulp xylan was obtained at 5$0^{\circ}C$ in both kraft pulps. The optimum pH of the enzyme for the hydrolysis of pulp xylan was 8.0 and more than 90% of the maximal activity was detected at 9.0. The positive effects of xylanase pretreatment on bleachability of softwood and hardwood kraft pulps were observed. The kappa number of softwood and hardwood kraft pulps was decreased by 3.7 and 2.0 units, respectively. The pulp fibre integrity was not significantly affected by xylanase pretreatment when the physical properties of handsheets made from xylanase-treated pulps were compared with those of handsheets from untreated pulps. These results indicate that the alkaline xylanase of Cephalospotium sp. RYM-202 is well suitable for application in enzymatic prebleaching of softwood and hardwood kraft pulps under the alkaline conditions.

• Korean Journal of Plant Resources
• /
• v.15 no.3
• /
• pp.269-278
• /
• 2002

To establish the mass propagation methods of Weigela subsessilis,, a promising native plant species for horticultural use, several factors influencing rooting from stem cuttings were evaluated. Softwood cuttings showed best rooting rate, 70~77%, in all the cutting media tested, 2.8 times more than hardwood cuttings in which perlite was best medium. The rooting from hardwood cuttings was promoted by higher concentration of all growth regulators used,500 mg.L$^{-1}$ NAA being the best with 80%. More than 80% of softwood cuttings treated by growth regulators produced roots, especially 100, 500, and 1000mg.L$^{-1}$ NAA producing 97％. Roofings from semi-wood cuttings was enhanced by all the growth regulators, except 1000 mg.L$^{-1}$ concentration in which rooting was reduce. Higher rooting rate was obtained by higher concentration and longer soaking duration of NAA in case of hardwood cutting. Softwood cutting showed 100 ％ rooting by soaking treatment with 500 mg.L$^{-1}$ NAA for 3 min. Rooting rate of semi-hardwood cuttings was promoted by higher concentration and longer soaking with growth regulators, However, the degree of improvement was lower than soft and hardwood cutting.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.5 s.108
• /
• pp.62-68
• /
• 2004

The amount of non-lignin components in unbleached and oxygen-delignified kraft pulps and their impact on lignin determinations was investigated. The lignin analyses investigated were kappa number and Klason lignin in conjunction with acid-soluble lignin. The species investigated were loblolly pine, and aspen. The non-lignin components that impacted on lignin determination were residual extractives and hexenuronic acid in unbleached and oxygen-delignified kraft pulps. In the hardwoods, significant amounts of extractives remained after kraft pulping and oxygen delignification. These residual extractives in the hardwood pulps had an impact on the lignin determination, more so on the acid lignin method than kappa number. Hexenuronic acid only impacts on kappa number determination both softwood and hardwood pulps, not on acid lignin. Hexeneuronic acid contributed as lignin content more in aspen than pine pulps, and more in oxygen-delignified than unbleached kraft pulps. Impact of hexenuronic acid on should be corrected both softwood and hardwood pulps for accurate kappa number.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.41 no.5
• /
• pp.20-25
• /
• 2009

Residual extractives had a noticeable impact on the brightness of unbleached hardwood kraft pulps (trembling aspen). The brightness-impacting extractives were effectively removed by oxygen delignification. In addition, oxygen delignification was more effective in removing chromophores in hardwood unbleached kraft pulps than in those of softwood (loblolly pine). The residual extractives in unbleached hardwood kraft pulps also affected the pulp color, primarily redness and the L value. These redness-related extractives in unbleached hardwood kraft pulps were also effectively removed by oxygen delignification. There were no significant color differences between untreated and solvent-extracted oxygen-delignified aspen kraft pulps. The residual extractives in unbleached and oxygen-delignified softwood (loblolly pine) kraft pulps did not have a significant impact on either brightness or pulp color.

• Korean Journal of Medicinal Crop Science
• /
• v.12 no.4
• /
• pp.285-288
• /
• 2004

This Study was carried out to select bed soil and growth regulator which are effective for the macro propagation by cutting of Cudrania tricuspidata Bureau. The rooting of Cudraniae tricuspidata showed good result when the bed soil was coarse soil, rooted hardwood cutting 56.9%, and softwood cutting 62.3%. The rooting of Cudraniae tricuspidata showed good result when treated by growth regulator IBA 100 ppm, rooted hardwood cutting 57.9%, and softwood cutting 89.2%.

• Journal of the Korea Furniture Society
• /
• v.26 no.3
• /
• pp.222-228
• /
• 2015

To evaluate the natural decay durability of valuable domestic softwoods which are used for preservative treatment in our country, we carried out decay test by European standard method. Of all test wood species, Japanese larch (Larix leptolepis) showed slightly high natural decay durability compared to other 4 wood species, Japanese red pine (Pinus densiflora), pitch pine (Pinus rigida), Japanese cedar (Cryptomeria japonica), and scots pine (Pinus sylvestris). However, all of evaluated domestic softwood species in this study caused high weight losses over about 30% in heartwood by test fungus, Poria placenta. We can hardly expect a good natural decay durability from these softwood species. According to the classification of the natural durability of European standard (EN 350-1), they are classified into "Not durable" or "Slightly durable". Therefore, if using these softwoods as exterior materials, we must do preservative treatment to ensure durability.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.27 no.4
• /
• pp.50-58
• /
• 1999

This study was carried out to investigate the growth characteristics and propagation methods of L. obtusiloba as a woody landscape plant. The results are obtained as follows: L. obtusiloba was dioecious shrub and shaped with bush type. Leaves were ovate, obtuse, cordate, 7.05 cm long, 7.20 cm wide, and petiole 2.0 cm long. Flowers of L. obtusiloba were diclinous. Soil acidity ranged from pH 4.06 to 5.53 with the lowest at the Mt. Soo-Ri. Mt. Soo-Ri located near factory district, which was considered to damaged by environmental deteoration. While soil organic matter was highest at Mt. Soo-Ri, inorganic nutrients were low. L. obtusiloba grows in the area with low soil acidity and low content of inorganic. Therefore it seemed to be tolerant to air pollution. L. Obtusiloba was high seed germination rate in the plug box and its shoots were longer than seeding box and softwood cutting of L. obtusiloba showed the rooting rate of 50% at 5,000ppm on June 23. To develop a mass propagation method of Korean native L. obtusiloba through an axillary bud culture as a woody landscape plant, about 2∼3 cm shoots induced from explant were subcultured to new media contained different growth regulators. Shoots multiplied most effectively on a WPM containing 1.0 mg/l BA, producing 5.5 shoots with a shoot length of 2.5 cm per shoot explant.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.3
• /
• pp.47-54
• /
• 2015

In this study, effects of kneading treatment on the properties of hardwood bleached kraft pulp (HwBKP), softwood bleached kraft pulp (SwBKP) and hardwood bleached chemi-thermo-mechanical pulp (HwBCTMP) were elucidated with a laboratory two-shaft kneader. Kneading treatment was performed at 30% (w/w) of pulp concentration and the number of passes through the kneader was adjusted from 0 to 10 passes. Then, changes in properties of pulp fibers were evaluated. It was found that fiber characteristics were influenced by kneading treatment. Fiber length was decreased with kneading while other morphological properties such as fiber width, curl and kink became increased as the number of passes through the kneader increased from 0 to 5 passes. The magnitude of changes in the morphological properties of softwood chemical pulp was the largest, followed by hardwood chemical pulp. The morphological properties of HwBCTMP were little influenced by kneading treatment. Swelling of fiber measured by WRV was increased with kneading except of HwBCTMP.

• Journal of the Korea Furniture Society
• /
• v.26 no.2
• /
• pp.179-185
• /
• 2015

A study was carried out to observe the 1% aqueous safranine solution flow speed in longitudinal and radial directions of softwood G. biloba, ring-porous wood A. altissima, and diffuse- porouswood D. kaki. In radial direction, ray cells and in longitudinal direction tracheids, vessel and wood fiber were considered for the measurement of liquid penetration speed at less than 12% moisture contents (MC). The length, lumen diameter, pit diameter, end wall pit diameter and the numbers of end wall pits determined for the flow rate. The liquid flow in the those cells was captured via video and the capillary flow rate in the ones were measured. Vessel in hardwood species and tracheids in softwood was found to facilitate prime role in longitudinal penetration. Radial flow speed was found highest in ray parenchyma of G. biloba. Anatomical features like the length and diameter, end-wall pit numbers of ray parenchyma were found also responsible fluid flow differences. On the other hand, vessel and fiber structure affected the longitudinal flow of liquids. Therefore, the average liquid penetration depth in longitudinal tracheids of G. biloba was found the highest among all cells considered in D. kaki and A. altissima.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.4
• /
• pp.37-42
• /
• 1994

The adsorption of water vapor and equilibrium moisture content(EMC) of the specimens for four softwood species dried by conventional- and high temperature method and equilibrated to 15% of the target EMC condition at 25$^{\circ}C$ were determined by oven drying method and with moisture meters. The amount of adsorption for high temperature dried red pine was significantly higher than that of conventional kiln dried wood, while those of eastern white pine, eastern hemlock and Norway spruce were not significantly different between drying methods. EMCs of these four species determined by oven drying method and with capacitive admittance moisture meter were not significantly different between drying methods. EMC of high temperature dried red pine determined with resistance moisture meter was significantly higher than that of conventional kiln dried wood. But EMCs of other species did not show significant difference between drying methods. EMCs of conventional and high-temperature dried wood determined with electronic moisture meters, especially in the case of the capacitive-admittance moisture meter measurement, were lower than that determined by oven drying method.