• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1322-1327
• /
• 2005

This paper presents a single-stage ZVT full-bridge AC/DC converter for aerospace applications. The detailed operating principle and design consideration of this soft-switched converter are analyzed and described. The proposed circuit topology and control scheme are proposed to exhibit optimum performances (i.e. high power factor, high efficiency, ring-free and low EMI features). A laboratory prototype, 500W 5V/100A AC/DC converter was implemented. The simulation and experimental waveforms verify the feasibility of the proposed design.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1166-1168
• /
• 2003

In most power electronic applications, the AC power input provided by the electronic utility needs to first converted to a DC voltage. Such conversion is accomplished by a diode rectifier due to its circuit simplicity and low cost. However, since diode rectifiers have some intrinsic problems such as low power factor and high harmonic distortion, a wide use of such rectifiers may cause noises, malfunction and heat damage in both electrical power systems and electrical machinery systems. This paper proposes soft switched three-phase single switch boost-type converter. The proposed circuit can perform Zero Voltage Switched(ZVS) without using any current and voltage sensors. For this circuit, both simulation and experiments have been performed. The results not only confirmed the ZVS but also indicated that, compared to the conventional hard switched converter, the prosed circuit can improve the efficiency as much as 1.7 to 4.7[%] while keeping the same high power factor and small harmonic distortion in their AC input.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1539-1548
• /
• 2018

This paper introduces a new soft switched AC-DC boost converter with power factor correction (PFC). In the introduced converter, all devices are turned on and off under soft switching (SS). The main switch is turned on under zero voltage transition (ZVT) and turned off under zero current transition (ZCT). The main diode is turned on under zero voltage switching (ZVS) and turned off under zero current switching (ZCS). Meanwhile, there is not any current or voltage stress on the main devices. Besides, the auxiliary switch is turned on under ZCS and turned off under ZVS. The detailed theoretical analysis of the converter is presented, and also theoretical analysis is verified by a prototype with 100 kHz and 500 W. Also, the proposed converter has 99.8% power factor and 97.5% total efficiency at soft switching operation.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.6
• /
• pp.484-489
• /
• 2020

This study proposes a new soft-switching three-level flying capacitor converter with low filter inductance. The proposed converter can achieve zero voltage switching (ZVS) turn-on of all switches by using auxiliary components La and Ca. It can also reduce filter inductance because the applied voltage of the filter inductor is decreased by using the flying capacitor. Furthermore, filter inductance can be reduced because the operating frequency of the filter inductor is doubled by the phase shifting between switches S3 and S4. The operation principle, design of passive components for ZVS turn-on, interleaving effects, and comparison of different topologies are presented. The experimental waveforms of a 1 kW two-phase interleaved converter prototype are provided to verify the validity of the proposed converter.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1629-1638
• /
• 2016

Differential power processing (DPP) systems are among the most effective architectures for photovoltaic (PV) power systems because they are highly efficient as a result of their distributed local maximum power point tracking ability, which allows the fractional processing of the total generated power. However, DPP systems require a high-efficiency, high step-up/down bidirectional converter with broad operating ranges and galvanic isolation. This study proposes a single, magnetic, high-efficiency, high step-up/down bidirectional DC-DC converter. The proposed converter is composed of a bidirectional flyback and a bidirectional isolated switched-capacitor cell, which are competitively cheap. The output terminals of the flyback converter and switched-capacitor cell are connected in series to obtain the voltage step-up. In the reverse power flow, the converter reciprocally operates with high efficiency across a broad operating range because it uses hard switching instead of soft switching. The proposed topology achieves a genuine on-off interleaved energy transfer at the transformer core and windings, thus providing an excellent utilization ratio. The dynamic characteristics of the converter are analyzed for the controller design. Finally, a 240 W hardware prototype is constructed to demonstrate the operation of the bidirectional converter under a current feedback control loop. To improve the efficiency of a PV system, the maximum power point tracking method is applied to the proposed converter.

• Journal of Power Electronics
• /
• v.10 no.2
• /
• pp.125-131
• /
• 2010

Switched-resonator converters are a new family of soft switching DC-DC converters where the energy is transferred via a resonator. This paper introduces some isolated topologies of this family. The achieved advantages include, load independent soft-switching, self short-circuit protection, and optimization capability due to topology variety. Compared to conventional series-resonant converters, outstanding advantages such as a smaller fewer number of switches and diodes, a smaller transformer, and lower current stresses are achieved. A general synthesis scheme, functional topologies, and essential relations are included. Experimental results from a laboratory prototype confirm the presented theoretical analysis.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.74-78
• /
• 1998

The shortcomings of zero-voltage-transition PWM converter is discussed and a new family of topologies of zero-voltage-transition PWM converter with soft-switched auxiliary switch is introduced. The experiments on a 290W boost converter and a 100W forward converter are carried out to prove the circuit. The efficiency increment of the new circuits are 2-5% comparing to hard switching circuits, and the switching noise is also greatly reduced.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.438-439
• /
• 2011

In this paper, soft switching bidirectional DC-DC converter is proposed. The proposed topology is added two auxiliary switches, two resonant capacitors and one resonant inductor to convectional bidirectional DC-DC converter. Therefore, this proposed topology can reduce switching loss of each power switch by ZVS (Zero Voltage Switching) and ZCS (Zero Current Switching). We have performed mode analysis, simulation and experiment for the proposed topology.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.12
• /
• pp.813-820
• /
• 2000

A technique to suppress the low frequency ripple voltage of the DC output in three phase buck diode converter is presented in this paper. The proposed pulse frequency modulation methods and duty ratio modulation methods are employed to regulate the output voltage of the buck diode converter and guarantee zero-current-switching(ZCS) of the switch over the wide load range. The proposed control methods used in this paper provide generally good performance such as low THD of the input line current and unity power factor. In addition, control methods can be effectively used to suppress the low frequency ripple voltage appeared in the dc output voltage. The harmonic injection technique illustrates its validity and effectiveness through the simulations and experiments.

• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.210-213
• /
• 1991

The clamp mode Zero-Volatge-Switched Multi-Resonant-Converter(ZVS-MRC) is proposed. In the converter, the performance of the conventional ZVS-MRC is improved by clamping the drain-to-source voltage of the power switch using a soft switching nondissipative active clamp network. The analysis for each stage of the converter operation modes is presented and is verified by experiments.