• Land and Housing Review
• /
• v.2 no.2
• /
• pp.163-170
• /
• 2011

Individual Vacuum Pressure Method (IVPM) is a soft ground improvement technique, in which a vacuum pressure can be directly applied to the vertical drain board to promote consolidation and to strengthen the soft ground. This method does not require surcharge loads, different to embankment or pre-loading method. In this study, the ground improvement efficiency of Individual Vacuum Pressure Method was estimated when suction pressure increases step by step(-20, -40, -60, -80kPa) with different periods. During Individual Vacuum Pressure Method process, surface settlement and pore pressure were monitored, and cone resistance as well as water content were also measured after the completion of Individual Vacuum Pressure Method treatment. From the results, optimum duration of each step of vacuum pressure was determined, and the settlement was calculated using FEM numerical analysis.

• Journal of Powder Materials
• /
• v.13 no.4 s.57
• /
• pp.256-262
• /
• 2006

The amorphous $Fe_{73}Si_{16}B_7Nb_3Cu_1$ alloy strip was pulverized to get a flake-shaped powder after annealing at $425^{\circ}C$ for 90 min and subsequently ground to obtain finer flake-shaped powder by using a ball mill. The powder was mixed with polyimide-based binder of $0.5{\sim}3wt%$, and then the mixture was cold compacted to make a toroidal powder core. After crystallization treatment for 1 hour at $380{\sim}600^{\circ}C$, the powder was transformed from amorphous to nanocrystalline with the grain size of $10{\sim}15nm$. Soft magnetic characteristics of the powder core was optimized at $550{\sim}600^{\circ}C$ with the insulating binder of 3wt%. As a result, the powder core showed the outstanding magnetic properties in terms of core loss and permeability, which were originated from the optimization of the grain size and distribution of the insulating binder.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2004.03b
• /
• pp.235-242
• /
• 2004

For this study, a Peliyagoda area located on a route was selected among many sections of a CKE(Colombo to Katunayake Expressway) route in Sri-Lanka. Its subground consists of a very weak and thick peat soil named amorphous or fibrous peat. All of data, obtained in the design process of soft ground treatment were analyzed to evaluate the settlement characteristics resulted from an embankment load and to present reasonable methods for estimation of secondary compression settlement. For these purposes, soil parameters were used obtainedby field and laboratory tests the settlement analyses were conducted base on the field monitoring results within 20 months. In addition, Reasonable methods were studied to estimate primary consolidation and secondary compression settlement.

• 보존과학연구
• /
• s.32
• /
• pp.99-112
• /
• 2011

The three-storied stone pagoda located in Seungansaji temple site consists mainly of medium to fine-grained biotite granite and granitic gneiss, and partly macrocrystalline gneiss, muscovite gneiss and gabbro. The surface of the stone pagoda is extensively colonized by lichen and moss due to surrounding trees and lawns, and severly deteriorated. Therefore, a comprehensive deterioration diagnosis has been carried out and conservation treatment was conducted in this study. For the conservation treatment, dry cleaning is performed throughout all the surface of the pagoda for naturally grown lichen and biological contaminants using a soft brush and wooden knife. Crustose lichen strongly adhere to the surface was removed by wet cleaning using distilled water. Also, protective railings were reinstalled to an appropriate height with taking the distance from the stone pagoda into account. Finally, the ground around the stone pagoda was repaired with clay sand, and dike was installed with a natural gradient to facilitate water drainage.

• Journal of Korean Foot and Ankle Society
• /
• v.8 no.2
• /
• pp.117-120
• /
• 2004

Purpose: The purpose of this study was to evaluate the effect and short-term results of the modified Mau osteotomy designed by the author. Materials and Methods: Seventeen feet treated with newly designed osteotomy from 2003 to 2004 were included. We performed metatarsal osteotomy and distal soft tissue procedure on 17 feet (12 patients) and additional Akin osteotomy on 6 feet (4 patients). An oblique osteotomy was made from the neck in the dorsum, aiming proximal to the base of the first metatarsal with vertical short arm on the base. We performed long arm of osteotomy parellel to the acrylic plate which was supposed as ground plane. Preoperative radiographs and follow up radiographs at three month were used for radiologic evaluation. Results: Mean hallux valgus angle was $43.6^{\circ}$ and mean intermetatarsal angle was $20.4^{\circ}$ on preoperative weight bearing radiograph. Mean amount of correction of the hallux valgus angle was $37.5^{\circ}$ and intermetatarsal angle was $14.2^{\circ}$ at three months after operation. There was no fixation loss or malunion, and the clinical result was subjectively exellent. Conclusion: More proximal rotational axis can achieve sufficient intermetatarsal angle correction, and vertical arm can provide more stable contact. So this newly modified Mau osteotomy was considered as a good alternative procedure in the treatment of severe hallux valgus.

• Journal of Convergence for Information Technology
• /
• v.7 no.1
• /
• pp.67-73
• /
• 2017

Paper sludge ash, blast furnace slag, fine powder quicklime, anhydrous gypsum, and fly ash as the main ingredients were prepared to suit the salty soils of marine soils. The solidification component is a kind of recycled ceramic, and CaO plays an important role in solidification. The neutralization time after solidification was about 2 weeks, and the compressive strength was about 12N/mm2 in the mortar test after one week incubation with standard yarn. This is about 14 times stronger than the solidifying agent used in the metropolitan area. As a result of applying plate load test to saltous marine soils, we obtained the yield load that can pass the large scale even after 5 days. In the uniaxial compressive strength test, shear strength of about 300 kPa was obtained after 5 days. It will be useful for supplementing the soft ground in the area where marine reclamation is much like the Incheon area.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.3
• /
• pp.43-53
• /
• 2013

In this study, an analysis about the causes of different types of excavation on accidents is required in order to prevent the frequently occurring accidents related to the earth retaining structure and excavation. Also, analysis of influence was performed by using numerical typical soil conditions and construction trend using numerical analysis method. According to the analysis results of 25 accident cases, the main influence factors were found as following: insufficient of soil survey, instability of temporary facility and lack of groundwater treatment, etc. Furthermore, in the numerical analysis result of 22 cases, drainage method was occurred larger settlement than waterproof method in the Inland. In case of applying the earth anchor method, it needs more detailed in the regions, which are discovered soft ground or rock discontinuities. Also, The consolidated clay absolutely needs further consideration of excess hydrostatic pressure.

• Korean Journal of Agricultural Science
• /
• v.3 no.1
• /
• pp.95-104
• /
• 1976

This study was conducted to test the harvesting operation of two kinds of rice varieties such as Milyang #15 and Tong-il with a imported two furrow Japanese combine and was performed to find out the operational accuracy of it, the adaptability of this machine, and the feasibility of supplying this machine to rural area in Korea. The results obtained in this study are summarized as follows; 1. The harvesting test of the Milyang #15 was carried out 5 times from the optimum harvesting operation was good regardless of its maturity. The field grain loss ratio and the rate of unthreshed paddy were all about 1 percent. 2. The field grain loss of Tong-il harvested was increased from 5.13% to 10.34% along its maturity as shown in Fig 1. In considering this, it was needed that the combine mechanism should be improved mechanically for harvesting of Tong-il rice variety. 3. The rate of unthreshed paddy of Tong-il rice variety of which stem was short was average 1.6 percent, because the sample combine used in this study was developed on basisof the long stem variety in Japan, therefore some ears owing to the uneven stem of Tong-il rice could nat reach the teeth of the threshing drum. 4. The cracking rates of brown rice depending mostly upon the revolution speed of the threshing drum(240-350 rpm) in harvesting of Tong-il and Milyang #15 were all below 1 percent, and there was no significance between two varieties. 5. Since the ears of Tong-il rice variety covered with its leaves, a lots of trashes was produced, especially when threshed in raw materials, and the cleaning and the trashout mechanisms were clogged with those trashes very often, and so these two mechanisms were needed for being improved. 6. The sample combine of which track pressure was $0.19kg/cm^2$ could drive on the soft ground of which sinking was even 25cm as shown in Fig 3. But in considering the reaping height adjustment, 5cm sinking may be afford to drive the combine on the irregular sinking level ground without any readjustment of the resaping height. 7. The harvesting expenses per ha. by the sample combine of which annual coverage area is 4.7 ha. under conditions that the yearly workable days is 40, percentage of days being good for harvesting operation is 60%, field efficiency is 56%, working speed is 0.273m/sec, and daily workable hours is 8 hrs is reasonable to spread this combine to rural area in Korea, comparing to the expenses by the conventional harvesting expenses, if mechanical improvement is supplemented so as to harvest Tong-il rice. 8. In order to harvest Tong-il rice, the two furrow combine should be needed some mechanical improvements that divider can control not to touch ears of paddy, the space between the feeding chain and the thrshing drum is reduced, trash treatment apparatus must be improved, fore and rear adjust-interval is enlarged, and width of track must be enlarged so as to drive on the soft ground.

• The Journal of Korean Physical Therapy
• /
• v.16 no.1
• /
• pp.85-123
• /
• 2004

Back ground : Subcutaneous fat area is the main factor involved in replacement disease and arteriosclerosis. Simple weight control is the appropriate medical treatment. It's understood that weight reduction does not only reduce the fat concentrations in blood but also reduces blood pressure, improves glucose levels in diabetes patients and reduces incidents of heart disease. there are several methods for reducing fat in the abdominal region but their effectiveness is not folly understood. one method is electrical stimulation of the problem areas. Method : From May 1st 2002 to October 31st. The 15 subjects who received medical examination were aged between 25 and 53 and were of mixed gender. The subjects were divided into two groups one to received functional electrical stimulation and the other a control group. Using Broca's criterion for judging fat grades. I analysed the differences between the two groups before and after the treatment. Subjects received functional electrical stimulation on the abdominal muscle intensity 50Hz. They received this treatment 4 days a week for 40 minutes a day. In the case of aerobic exercise, at the Treadmill, we used it with the intensity of $75\%$ maximum heart rate (220-age). Result 1)After functional electrical stimulation in the case of male subjects, the weight was reduced 1.93kg, obesity $2.60\%$, fat mass 2.73kg, Percent body fat $4.40\%$, waist circumference 6.53cm, circumference of hips 5.53cm. On the other side, the quality of muscle was increased at the rate of 1.03kg, but it's not attentional level. The subcutaneous fat area was reduced by $26.63cm^2$, the visceral fat area was reduced by $43.00cm^2$, In the female subjects, we can see the reduction of fat grade by $26.63cm^2$, the quantity of body fat by 1.5kg, percent body fat by $1.77\%$, circumference of waist by 4.02cm, circumference of hips by 3.67cm, weight by 1.40kg but was increased 0.72kg at the quantity of muscles. We can see the reduction also in the subcutaneous fat area $24.03cm^2$, the visceral fat area by $25.36cm^2$. 2)After aerobic exercise, on the male subjects, we can see reduction of weight by 3.36kg, obesity by $4.00\%$, fat mass by 2.83kg and we can see increase at the soft lean mass by 2.96kg, but we can see reduction, the percent body fat by $3.03\%$, fat distribution by $0.023\%$, circumference of waist by 3.10cm, circumference of hips by 2.23cm. The female subjects show a reduction in the weight by 2.48kg, percent body fat by $2.20\%$, show an increase in the soft lean mass by 1.54kg. We can see a reduction in the quantity of fat mass by 2.32kg, the percent body fat by $2.80\%$, the circumference of waist by 2.16cm, the circumference of hips by 2.68cm, the fat distribution by $0.016\%$, the subcutaneous fat area by $15.25cm^2$ the visceral fat area by $11.52cm^2$. After aerobic exercise, we can't see the attentional change at the total cholesterol, triglyceride, high density lipoprotein cholesterol, low density lipoprotein cholesterol. 3)After the application of functional electrical stimulation and aerobic exercise, in result of measurement on the body ingredient, we could see the weight reduction and increase the quantity of muscle with the male group who exercised aerobic. We can see the attentional rate on the electrical stimulation about abdominal fat rate, circumference of waist, circumference of hips. The other hand, I couldn't see the attentional differences between the two groups in the rate of fatness and quantity of body fat and the rate of body fat. There isn't any attentional difference in the area of fat under skin, on the contrary, There is attentional difference in the fat in the internal organs area at the electrical stimulation site. We can't see the attentional change of total cholesterol, triglyceride, high density lipoprotein cholesterol, low density lipoprotein cholesterol between electrical stimulation and aerobic exercise. 4)After execution of functional electrical stimulation and aerobic exercise, in result of measurement on change of body ingredient among female objects, We could see weight reduction, increase at muscle quantity in the aerobic exercise group. We could see the attentional differences in the rate of fatness, the rate of abdominal region, the circumference which received electrical stimulation. But, we couldn't see the attentional differences between two groups in the quantity of body fatness, the circumference of hips. The subcutaneous fat area doesn't show the attentional differences. On the Contrary, we could see lots of differences in the visceral fat area of the electrical stimulation group. Conclusion The results show that functional electrical stimulation and aerobic exercise have insignificant differences when if comes to total cholesterol, triglyceride, high density lipoprotein cholesterol, low density lipoprotein cholesterol. Though there is affirmative change in body ingredient after both electrical stimulation and aerobic exercise. Functional electrical stimulation is more effective on the subcutaneous fat area and in changing visceral fat area. There fore. It is concluded that the physical therapy is more effective in the treatment of abdominal fatness.

• Tuberculosis and Respiratory Diseases
• /
• v.56 no.3
• /
• pp.308-314
• /
• 2004

Atelocollagen have been used recently in skin and other soft tissue defect regions more than silicone fluid because of the low incidence of an immune reaction and complications. Several cases of acute pneumonitis after a subcutaneous injection of silicone have been reported. The symptoms were dyspnea, fever, chest pain and hemoptysis. Previous reports have explained the pathophysiology of acute pneumonitis to a pulmonary microembolism and cellular inflammation. We experienced two cases of an acute interstitial pneumonitis and pulmonary hemorrhage after a subcutaneous injection of atelocollagen. They were all healthy young women and complained of dyspnea, fever and blood tinged sputum. The chest radiography and computerized tomography showed a bilateral ground glass opacity in both lung fields. One case recovered completely with conservative treatment but the clinical course of the other case was aggravated to the degree that invasive positive pressure ventilation therapy was required. We report a rare case of a diffuse pulmonary alveolar hemorrhage and an interstitial pneumonitis after the subcutaneous injection of atelocollagen for cosmetic purposes.