• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.97-103
• /
• 2004

In this paper, we propose a high speed block turbo code decoding algorithm and an efficient hardware architecture. The multimedia wireless data communication systems need channel codes which have the high-performance error correcting capabilities. Block turbo codes support variable code rates and packet sizes, and show a high performance due to a soft decision iteration decoding of turbo codes. However, block turbo codes have a long decoding time because of the iteration decoding and a complicated extrinsic information operation. The proposed algorithm using the threshold that represents a channel information reduces the long decoding time. After the threshold is decided by a simulation result, the proposed algorithm eliminates the calculation for the bits which have a good channel information and assigns a high reliability value to the bits. The threshold is decided by the absolute mean and the standard deviation of a LLR(Log Likelihood Ratio) in consideration that the LLR distribution is a gaussian one. Also, the proposed algorithm assigns '1', the highest reliable value, to those bits. The hardware design result using verilog HDL reduces a decoding time about 30% in comparison with conventional algorithm, and includes about 20K logic gate and 32Kbit memory sizes.

• Journal of Life Science
• /
• v.14 no.5
• /
• pp.761-769
• /
• 2004

This study was investigated the occurrence of sclerotinia rot caused by Sclerotinia sclerotiorum at the major perilla cultivating area, Gangdong-dong, Gangseo-gu, Busan in 1998. The incidence of this disease ranged from 8.1 to 28.3% at Gangdong-dong area during the growing seasons. Symptoms of the disease initially appeared damping-off of infected stems and soft-rot on the leaves of perilla. Under the relatively high humidity, abundant white mycelia of the pathogen formed on the lesion developed into black sclerotia later and the infected leaves were finally fell down. Sixteen isolates, Sl-S16, isolated from diseased lesions showing typical symptoms, and pathogenicity was tested using mycerlial disks. Among them, S2 isolate showing the most strong pathogenicity was selected and identified as Sclerotinia sclerotiorum on the basis of morphological and cultural characteristics. For biological control, an antagonistic bacteria, N4 isolate which effectively inhibited not only mycelial growth of S2 isolate but also suppress sclerotinia rot on the pot assay, was selected and identified as Bacillus megaterium according to Bergey's manual and API system., Wettable powder type, N4 formulation using B. megaterium N4 isolate was developed and estimated its control effect on perilla crops in a plastic house. As a results, N4 formulation which applied before 3 days inoculation of pathogen was effectually controlled Sclerotinia rot as the control value of 98.0%, was more effective than chemical fungicide, benomyl showing the control value of 78.0%. This is the first report of wettable powder formulation as a biocontrol agent using B. megaterium N4 against Sclerotinia rot caused by S. sclerotiorum on perilla.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.25 no.4
• /
• pp.50-60
• /
• 1983

305 samples of alluvial deposit in inland and harbour districts were selected and consolidation charateristics of the alluvium were put in order statiscally. The correlations between them were as follows. 1. The relationships between LL(liguid limit) and Cc (compression index) were explained as Cc=0. 03(LL-21. 7) in case of inland district soil and as Cc=0. 019(LL-19) in case of harbour district soil. As compared with formular proposed by Skernpton, the gradient of this linear line was slight steep. 2. The relationships between PI(plastic index) and Cc were explained as Cc=0. 063 PI-0. 52 in case of inland district soil and Cc=0. 043 PI-0. 31 in case of harbour district soil. 3. As void ratio and natural moisture content were increased, Cc was increased, and as wet density was increased, Cc was decreased with a gentle curve. 4. As LL and P1 increased, mv(coefficient of volume compressibility) was increased but if LL and P1 was increased beyond a certain extend, mv has a tendency of constant value, that is, mv show a tendency to take constant value in the very soft clay. and mv in P=2. 5kg/cm$^2$ was about l${\times}$ l0-$^1$cm$^2$/kg in case of land district soil and 6x 10-$^1$crn$^2$/kg in case of harbour district soil lower than that in P=0. 25kg/crn2. 5. Cv(coefficient of consolidation) was a tendency to decrease with a gentle curve as LL was increased, and Cv in P=0. 25kg/crn2 was about 3x l0-$^1$crn$^2$/min larger than that in P=2. 5kg/crn$^2$. 6. Relationships between Py(pre-consolidation pressure) which is included over consolidation soil and ∑r1h(effective over-burden pressure) were explained as Py=l. 12 ∑r'h in case of land district soil and as Py=l. l5∑r'h in case of harbour district soil. 7. Some of the properties show good correlations between them, practical and effective applications of these correlations are expected in the planning and excution of soil investigation and also in the evaluation of the results.

• Science of Emotion and Sensibility
• /
• v.5 no.2
• /
• pp.23-28
• /
• 2002

The purpose of this study was to classify apparel fabrics according to rustling rounds and to analyze their transformed colors and mechanical properties. The rustling sounds of apparel fabrics were recorded and then transformed into colors using Mori's color-transforming program. The specimens were clustered into five groups according to sound properties, and each group was named as ‘Silky’,‘Crispy’,‘Paper-like’,‘Worsted’, and ‘Flaxy’, respectively. The Silky consisted of smooth and soft silk fabrics had the lowest value of LPT, $\Delta$f, ARC , loudness(B) and sharpness(z). Their transformed colors showed lots of red portion and color counts. The Crispy with crepe fabrics showed relatively low loudness(z) and sharpness(B), but diverse colors and color counts were appeared. The Paper-like showed the highest value of LPT, $\Delta$f and loudness(z). The Worsted composed of wool and wool-Like fabrics showed high values of LPT, $\Delta$f, loudness(z) and sharpness(B). The transformed rotors of the Paper-like and Worsted showed the blue mostly but color counts were less than the others. The Flaxy with rugged flax fabric had the highest fluctuation strength, and their transformed colors showed diversity.

• Journal of Bio-Environment Control
• /
• v.21 no.4
• /
• pp.404-410
• /
• 2012

This study was conducted to examine effects of harvest time (09:00 vs. 14:00), precooling at $4^{\circ}C$ vs. no precooling, and storage temperature (4 vs. $8^{\circ}C$) on the storage life of 'Maehyang' strawberry fruits for export. Fruits at a 60% ripe stage were harvested from a commercial greenhouse in Gyeongsangnamdo, Jinju on May 4, 2010. Fruits were precooled by a forced draft cooling for three hours, transported for about 30 minutes and then stored, immediately. Small precoolers set in the farm were used for precooling. Fruits were placed in constant temperature chamber (4 or $8^{\circ}C$) after packaging using PVC wrap and a cardboard box. Fruits were examined for their changes in weight, hardness, Hunter color values, soluble solids content (SSC), and incidence of gray mold (Botrytis cinerea) during storage at a two days interval from May 6 to May 14, 2010. Hardness and SSC decreased as the ripening stage progressed. The Hunter's 'L' and 'a' value of fruit color decreased as time passed. Also, fresh weight decreased during storage at all temperatures. Soft rot appeared on epidermal tissues and followed by gray mold. Incidence of gray mold was greater at $8^{\circ}C$ storage temperature than in $4^{\circ}C$ storage temperature. However, no difference by the harvested time and precooling. The results indicate that effectiveness for keeping the freshness was best achieved by precooling at $4^{\circ}C$ and storage at $4^{\circ}C$, respectively.

• Korean journal of food and cookery science
• /
• v.21 no.6 s.90
• /
• pp.794-799
• /
• 2005

The overall effects of black rice wine (BRW) on black rice bread were examined through the gluten washing test, mixograph and image analysis by Cnunbscan. Commercially produced black rice flour had a much lower amount of gluten than the strong flour However, the mixture with $30\%$(flour basis) black rice flour and $70\%$ strong flour exhibited a good indication for bread making showing $30\%$ wet gluten and $14\%$ dry gluten. In the mixogram results, the peak time showed the highest value for $10\%$ added BRW, indicating an inappropriate level at $50\%$, and the changes of tail width after 8 minutes expressed that the dough became soft and sticky with increasing addition of BRW The volume of bread was increased when BRW was added, and showed the highest value at $20\%$ BRW. In relationship between the volume and bread characteristics, volume showed a highly negative relation with crumb fineness (r=-0.678) and a positive relation with crust thickness (r=0.693).

• Journal of the Korean Geotechnical Society
• /
• v.24 no.6
• /
• pp.5-16
• /
• 2008

This study investigated the existing theoretical backgrounds in order to examine the stability control method of lateral flow caused by the Plasticity of soils when unsymmetrical surcharge works on polluted soils and then compared and analyzed the results measured through model tests. Ultimate bearing power of ML and $ML_{p1}$ and $ML_{p2}$ obtained at surcharge(q)-settlement$(S_v)$ curve showed similar trends to ultimate bearing power obtained from control chart of deflection $(S_v-Y_m)$ by Tominaga.Hashimoto, that of $S_v-(Y_m/S_v)$ by Matsuo.Kawamura and that of $(q/Y_m)-q$ by Shibata.Sekiguchi and so it is considered that it has no problem in actual applicability. ${S_v-(Y_m/S_v)}$ of control chart of $ML_{p1}$ by Matsuo.Kawamura showed smaller value than ultimate bearing capacity value from surcharge-settlement curve $(q-S_v)$. Expression of ML of fracture baseline at stability control charge by Matsuo Kawamura is ${S_v=3.21exp}\{-0.48(Y_m/S_v)\}$ and expression of $ML_{p1}$ is ${S_v=3.26exp}\{-0.96(Y_m/S_v)\}$ and expression of $ML_{p2}$ is ${S_v=6.33exp}\{-0.45(Y_m/S_v)\}$.

• Korean Journal of Radiology
• /
• v.20 no.5
• /
• pp.812-822
• /
• 2019

Objective: To assess the diagnostic value of combining diffusion-weighted imaging (DWI) with conventional magnetic resonance imaging (MRI) for differentiating between pathologic and traumatic fractures at extremities from metastasis. Materials and Methods: Institutional Review Board approved this retrospective study and informed consent was waived. This study included 49 patients each with pathologic and traumatic fractures at extremities. The patients underwent conventional MRI combined with DWI. For qualitative analysis, two radiologists (R1 and R2) independently reviewed three imaging sets with a crossover design using a 5-point scale and a 3-scale confidence level: DWI plus non-enhanced MRI (NEMR; DW set), NEMR plus contrast-enhanced fat-saturated T1-weighted imaging (CEFST1; CE set), and DWI plus NEMR plus CEFST1 (combined set). McNemar's test was used to compare the diagnostic performances among three sets and perform subgroup analyses (single vs. multiple bone abnormality, absence/presence of extra-osseous mass, and bone enhancement at fracture margin). Results: Compared to the CE set, the combined set showed improved diagnostic accuracy (R1, 84.7 vs. 95.9%; R2, 91.8 vs. 95.9%, p < 0.05) and specificity (R1, 71.4% vs. 93.9%, p < 0.005; R2, 85.7% vs. 98%, p = 0.07), with no difference in sensitivities (p > 0.05). In cases of absent extra-osseous soft tissue mass and present fracture site enhancement, the combined set showed improved accuracy (R1, 82.9-84.4% vs. 95.6-96.3%, p < 0.05; R2, 90.2-91.1% vs. 95.1-95.6%, p < 0.05) and specificity (R1, 68.3-72.9% vs. 92.7-95.8%, p < 0.005; R2, 83.0-85.4% vs. 97.6-98.0%, p = 0.07). Conclusion: Combining DWI with conventional MRI improved the diagnostic accuracy and specificity while retaining sensitivity for differentiating between pathologic and traumatic fractures from metastasis at extremities.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.47 no.3
• /
• pp.86-94
• /
• 2024

In this study, an attempt was made to approximate the main characteristic values of Bi_0.5(Na_0.78K_0.22)_0.5TiO₃ (= BNKT) depending on the content of Fe₂O₃ additives, aiming to approach the values of lead(Pb) piezoelectric ceramic materials (PZT). Specifically, when the piezoelectric coefficient (d₃₃) value of lead(Pb) piezoelectric ceramic material (PZT polycrystalline ceramic powder) is 300[pC/N] or higher, it is applied for hard purposes such as ultrasonic welding machines and cleaning machines, and when it exceeds 330[pC/N], it is applied for soft purposes like piezoelectric sensors. In this study, research and development were conducted for devices with a piezoelectric coefficient (d₃₃) of 300[pC/N] or more for actuators. For this purpose, K⁺ exceeding 0.02 to 0.12 mol% was added to (Na_0.78K_0.22)_0.5Bi_0.5TiO₃ to analyze structural changes due to K⁺ excess, and (Na_0.78K_0.22)_0.5Bi_0.5TiO₃ + 8mol% K₂CO₃ Ti⁴⁺ was substituted with Fe³⁺ to manufacture lead-free piezoelectric materials. As a result, ceramics with Fe³⁺ substitution at x = 0.0075 yielded an average value of d₃₃ = 315[pC/N]. Furthermore, for ceramics with Fe³⁺ substitution at x = 0.0075, the average values of maximum polarization (P_max), residual polarization (P_rem), and coercive field (E_c) were found to be 39.63 μC/cm², 30.45 μC/cm², and 2.50 kV/mm, respectively. The reliable characteristic values obtained from the research results can be applied to linear actuator components (such as the zoom function of mobile cameras, LDM for skin care, etc.) and ultrasonic vibration components.

• Journal of Periodontal and Implant Science
• /
• v.23 no.3
• /
• pp.493-506
• /
• 1993

For maintenance of an ailing or failed implant it is essential to treat the implant fixture surface so as to remove bacterial endotoxin and make a surface tolerated by surrounding soft and hard tissue. Thus in this study the method that makes the smoothest surface treated with a high speed diamond bur, a low speed diamond bur, a stone, a rubber point or Jetpolisher was studied. With the profilomenter a mean value of $R_{max}$ was measured. The hight speed diamond, the rubber point and the Jetpolisher showed a mean $R_{max}\;7.77{\mu}m$. The low speed diamond bur, the rubber, point and the Jetolisher made a mean value of $R_{max}\;8.44{\mu}m$. The stone, the rubber point and the Jetolisher showed the smoothest surfaces with a mean value of $R_{max}\;6.24{\mu}m$. TPS (titanium plasma sprayed) areas showed a mean vlaue of $R_{max}\;24.42{\mu}m$, and the smooth surfaced titanium disc manufactured by the company (IMZ, Germany) shows a mean value of $R_{max}\;3.00{\mu}m$. Under the SEM examination the disc treated with a high speed diamond bur, a rubber point and a Jetpolisher showed partially remaining TPS particles, but the height of these particles were reduced remarkably compared with those of the original TPS. The disc treated with a low speed diamond bur, a rubber point and a Jetpolisher showed a rough topography with remaining TPS on the entire surface. A stone, a rubber point and a Jetpolisher removed almost TPS and the bulk titanium metal was exposed and some scratches were made by the stone. All treated discs were revealed as rougher than the smooth surface disc manufactured by the company. An untreated TPS disc shows a very irregular surface and a $40{\mu}m$ height of the plasma sprayed areas.