• 한국분말재료학회지
• /
• 제31권2호
• /
• pp.146-151
• /
• 2024

Pure SnO₂ has proven very difficult to densify. This poor densification can be useful for the fabrication of SnO₂ with a porous microstructure, which is used in electronic devices such as gas sensors. Most electronic devices based on SnO₂ have a porous microstructure, with a porosity of > 40%. In pure SnO₂, a high sintering temperature of approximately 1300℃ is required to obtain > 40% porosity. In an attempt to reduce the required sintering temperature, the present study investigated the low-temperature sinterability of a current system. With the addition of TiO₂, the compositions of the samples were Sn_1-xTi_xO₂-CoO(0.3wt%)-CuO(2wt%) in the range of x ≤ 0.04. Compared to the samples without added TiO₂, densification was shown to be improved when the samples were sintered at 950℃. The dominant mass transport mechanism appears to be grain-boundary diffusion during heat treatment at 950℃.

• Journal of Electrical Engineering and Technology
• /
• 제12권6호
• /
• pp.2348-2352
• /
• 2017

The electrical contact characteristics including temperature rise, contact resistance and arc erosion rate of the $Ag-SnO_2$ materials with increased $SnO_2$ content were investigated during the repeated make-and-break operations. The thickness of arcing melting layer reduces by half and the arc erosion rate decreases more than 70% under 10000 times operations at AC 10 A with the $SnO_2$ content increasing from 15 wt.% to 45 wt.%, on one hand, temperature rise and contact resistance increase obviously but could be reduced to the same order of conventional $Ag-SnO_2$ materials by increasing the contact force. The microstructure evolution and the effect of $SnO_2$ on the arc erosion, contact resistance were analyzed.

• Bulletin of the Korean Chemical Society
• /
• 제18권12호
• /
• pp.1291-1295
• /
• 1997

The catalytic dehydrocoupling of di-n-butylstannane n-Bu2SnH2 by the Cp2MCl2/Red-Al (M = Ti, Zr, Hf) and M(CO)6/Red-Al in situ combination catalysts yielded a mixture of two kinds of catenated products: one is a cross-linked insoluble solid, and the other is a non-cross-linked soluble solid (≒Sn5) or viscous oil (≒Sn2). The soluble oligostannanes could be produced by simple dehydrocoupling of n-Bu2SnH2, whereas the insoluble polystannanes could be obtained via disproportionation/dehydrocoupling combination process of n-Bu2SnH2. The disproportionation/dehydrocoupling combination process may initially produce a low-molecular-weight oligostannane with partial backbone Sn-H bonds which could then undergo an extensive cross-linking reaction of backbone Sn-H bonds, resulting in the formation of an insoluble polystannane.

• 한국주조공학회지
• /
• 제34권2호
• /
• pp.49-53
• /
• 2014

In commercial Zr-Nb-Cu-Ni-Al amorphous alloys, expensive element, Zr, was substituted to Sn which was cheaper one, and then, glass forming ability, compressive strength and hardness of them were estimated. Even though the Sn was added up to 1.5%, resulting phase was not changed to the crystalline form. It was confirmed by X-ray diffraction and thermal analyses. In the X-ray profiles, there were no peaks for crystalline phases and typical halo pattern for amorphous phase was appeared at the diffraction angle of $35^{\circ}{\sim}45^{\circ}$. Thermal analyses also showed that the Sn modified alloys were corresponded to the amorphous standards where ${\delta}T$(= Tx - Tg) and Trg(= Tg/Tm) affecting to the amorphous forming ability were more than 50K and 0.60 respectively. Compressive strengths were 1.77 GPa, 1.63 GPa, 1.65 GPa and 1.77 GPa for 0%Sn, 0.5%Sn, 1.0%Sn and 1.5%Sn respectively. Hardnesses of the Sn modified alloys were decreased from 752 Hv to 702 Hv in 1.0%Sn and recovered to 746 Hv in 1.5%Sn.

• 대한전자공학회논문지SD
• /
• 제43권8호
• /
• pp.13-18
• /
• 2006

Sn과 Zn 금속을 이용해 각각 산소와 아르곤 가스를 주입한 대기압 분위기에서 열처리를 통해 $SnO_2$와 ZnO 나노박막을 형성시켰다. 나노구조로 형성된 $SnO_2$ 박막의 경우 CO 가스(5,000 ppm)에 대해 $200^{\circ}C$의 동작온도에서 약 50 %의 감도를 나타내었으며, $SnO_2$ 나노 금속산화물에 Pt 금속을 이온 코팅법에 의해 첨가한 박막의 경우에는 동작온도 $150^{\circ}C$에서 73 %의 높은 감도를 얻을 수 있었다. 순수 ZnO 나노 박막의 경우 NOx(20 ppm) 가스에 대해 낮은 감도를 나타내었으나, Cu를 이온 코팅법에 의해 첨가한 박막의 경우에는 동작온도 $200^{\circ}C$에서 90 %의 높은 감도를 나타내었다. 나노 구조가 아닌 $SnO_2$와 ZnO 박막이 가지는 CO와 NOx에 대한 가스 감도에 비해 매우 높은 감도를 가짐을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제25권10호
• /
• pp.805-810
• /
• 2012

Transparent conducting oxides (TCOs) have wide range of application areas in transparent electrode for display devices, Transparent coating for solar energy heat mirrors, and electromagnetic wave shield. $SnO_2$ is intrinsically an n-type semiconductor due to oxygen deficiencies and has a high energy-band gap more than 3.5 eV. It is known as a transparent conducting oxide because of its low resistivity of $10^{-3}{\Omega}{\cdot}cm$ and high transmittance over 90% in visible region. In this study, co-doping effects of Al and Y on the properties of $SnO_2$ were investigated. The addition of Y in $SnO_2$ was tried to create oxygen vacancies that increase the diffusivity of oxygen ions for the densification of $SnO_2$. The addition of Al was expected to increase the electron concentration. Once, we observed solubility limit of $SnO_2$ single-doped with Al and Y. $\{(x/2)Al_2O_3+(x/2)Y_2O_3\}-SnO_2$ was used for the source of Al and Y to prevent the evaporation of $Al_2O_3$ and for the charge compensation. And we observed the valence changes of aluminium oxide because generally reported of valence changes of aluminium oxide in Tin - Aluminium binary system. The electrical properties, solubility limit, densification and microstructure of $SnO_2$ co-doped with Al and Y will be discussed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 C
• /
• pp.1487-1489
• /
• 1994

$(Zr_{0.65}Sn_{0.35})Ti_{1.04}O_4$ system which has a dielectric constant, low dielectric loss and temperature coefficient was investigated. Temperature coefficient varied from positive to negative with increasing of NiO. For the NiO content 1.0wt%. i.e $(Zr_{0.65}Sn_{0.35})Ti_{1.04}O_4$, the ceramic showed very good dielectric properties such as ${\epsilon}$=37.8, $Q{\times}f_o=49.000$ and ${\tau}_r= 4{\pm}1ppm/^{\circ}C$.

• 한국세라믹학회지
• /
• 제20권2호
• /
• pp.93-98
• /
• 1983

The sensitivity characteristics of $SnO_2$-based gas sensor prepared by sintering method have been studied at the presence of CO and Propane gas. Samples mixed with 1wt% $La_2O_3$ and 1wt% $PdCl_2$ showed highest sensitivity to CO and propane gas at 250$^{\circ}$C but the addition of $CeO_2$ did not enhance the sensitivity. For slectivity for gas a $SnO_2-La_2O_3$ (1wt%) sample without $PdCl_2$ showed better results. A sample sintered sintered at 115$0^{\circ}C$ has shown the optimum condition in sensitivity and electroding

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.171-171
• /
• 2009

The electrodes are usually made of a porous mixture of carbon-supported platinum and ionomers. $SnO_2$ particles provide as supports that have been used for DMFCs, and it have high catalytic activities toward methanol oxidation. The main advantage of $SnO_2$ supported electrodes is that it has strong chemical interactions with metallic components. The high activity to a synergistic bifunctional mechanism in which Pt provides the adsorption sites for CO, while oxygen adsorbs dissociative on $SnO_2$. The reaction between the adsorbed species occurs at the Pt/$SnO_2$ boundary. The morphological observations were characterized by FESEM and transmission electron microscopy (TEM). $SnO_2$ particles crystallinity was analyzed by the X-ray diffraction (XRD). The surface bonded state of the $SnO_2$ particles and electrode materials were observed by the X-ray photoelectron spectroscopy (XPS). The electric properties of the Pt/$SnO_2$ catalyst for methanol oxidation have been investigated by the cyclic voltametry (CV) in 0.1M $H_2SO_4$ and 0.1M MeOH aqueous solution. The peak current density of methanol oxidation was increased as the $SnO_2$ content in the anode catalysts increased. Pt/$SnO_2$ catalysts improve the removal of CO ads species formed on the platinum surface during methanol electro-oxidation.

• 대한치과기공학회지
• /
• 제23권1호
• /
• pp.55-64
• /
• 2001

This study is focusing on the improvement of problems of Ti-6Al-4V alloy. A new Ti based alloy, Ti-15Sn-4Nb, have designed to examine any possibility of improving the mechanical properties and biocompatibility. Specimens of Ti alloys were melted in vacuum arc furnace and homogenized at $100^{\circ}C$ for 24h. All specimens were solution treated at $812^{\circ}C$ and aged at $500^{\circ}C$ for 10h. The corrosion resistance of Ti alloys was evaluated by potentiodynamic polarization test and immersion test inl%Lactic acid solutions. Ti-15Sn-4Nb system alloys showed Widmanstatten microstructure after solution treatment which is typical microstructure of ${\alpha}+{\beta}$ type Ti alloys. Analysing the corrosion resistance of Ti alloys, it was concluded that the passive films of Ti-15Sn-4Nb system alloys are more stable than that of Ti-6Al-4V alloys. Also, the corrosion resistance of Ti-15Sn-4Nb system alloys was improved with adding elements, Hf. It was analysed that the passive film of the Ti-15Sn-4Nb alloy which was formed in air atmosphere was consisted of TiO2, SnO and NbO through X-ray photoelectron spectroscopy(XPS) analysis.