• Economic and Environmental Geology
• /
• v.7 no.3
• /
• pp.87-100
• /
• 1974

This paper deals with grain size analysis, heavy mineral analysis and trace element analysis of the recent sediments of Han River basin between Cheongpyong, Gyeonggi province and Seoul. For each location the samples are taken at river shoreline, river berm and river dune. The size analysis discloses that the mean values range from $-1.37{\phi}$ to $-1.60{\phi}$, sorting values range from 0.25 to 1.84, skewness values range from -0.44 to 0.51 and kurtosis values range from -0.1 to 1.75. Based on the textural parameters, the dune sand can be distinguished from the shoreline-berm sand. The content of heavy minerals of each sample ranges from 0.04 to 4.7%. The principal heavy minerals are ilmenite, magnetite, leucoxene, garnet, amphibole, pyroxene, kyanite, zircon, monazite, tourmaline, epidote, limonite, and minor minerals are apatite, sillimanite, andalusite and olivine. In general, dune sand samples contain more heavy minerals than the samples of shoreline or berm sand. This suggests that the heavy mineral concentration is affected by wind action more than by any other causes. The content of ilmenite and leucoxene decreases, whereas the content of zircon and epidote increases as it approaches the downstream region. The differences result from the variance of geological occurrences. The emission spectrochemical analysis and colorimetry analysis revealed that the content of Ni and V in the heavy minerals of the study area are higher than those of other stream sediments in Korea. On the other hand the content of Cu, Ph, Zn, Mo, W, P, Mn, Cr, Ag and Sn are lower in the study area. It has been observed also that the contents of all the elements except for Bi are higher in this area than the samples of marine sediments of Yellow Sea.

• Korean Journal of Metals and Materials
• /
• v.48 no.12
• /
• pp.1056-1063
• /
• 2010

We present a new joining method for Pd-Cu membrane foils used as permeation tubes to collect $CO_2$. Since foils have poor mechanical strength, joining should be done at low temperatures to reduce residual stresses and without joining pressure. This contradicts the well known conditions for good contact between base materials that determines joint qualities. We selected Sn-Ag-Cu alloys that are highly reactive with Pd and Cu as a filler metal. As the filler melts at joining temperatures as low as $220{\sim}280^{\circ}C$, Pd and Cu are dissolved into the melt and react with the filler elements, which raises the melting temperature of the filler based on eutectic structures among the elements. Then, isothermal solidification progresses for the rest of the joining time. Intermetallic compounds (IMC) in the joints, one of the main factors for brittle joints, are inevitably formed. However, by optimizing both joining time and temperature, we balanced the wettability with IMC. Sealing test results confirmed that the joints are mechanically reliable during operation.

• 한국해양학회지
• /
• v.24 no.3
• /
• pp.132-147
• /
• 1989

A total of 83 surface sediments and 55 sea water samples, collected from the southwestern sea of Cheju Island, were analyzed in order to understand their textural characteristics, geochemical composition and the clay mineralogical features. The sediments were subdivided into ten textural classes, namely clayey sand, slightly gravelly muddy sand, sandy clay, clay and mud. The coarse and fine-grained mixed sediments are distributed in the northern part and around the Island, whereas the fine-grained deposits are mainly distributed in the central and southern parts of the study area; small scale mud patches are distributed in the southwestern and northern parts of Cheju Island. The high concentration of total suspended matter in study area gradually increase toward the southwestern and northwestern offshore area. The concentration of geochemical elements is as follow: the content of Mn, Al, Zn, Cr, Cu and Sn increase toward the southern part which is covered mainly with fine-grained deoposits, whereas the content of Ca, Mg and Ag is higher in the northern area; the elements such as Ni, Na, Fe and Pb are more concentrated relatively in muddy deposits rather than in sandy sediments. The light minerals such as Na-Ca feldspars show a high content around the Socotra Rock, toward the Soheugsan and Cheju Islands, but the K-feldspars are relatively high around the Cheju Island. It was noticed that the provenance of these sediments is partly influenced by the geological characteristics near the island. X-ray diffractogram for clay minerals from the southeastern mud patch and around the Soheugsan Island shows the diagnostic calcite peak indicating that the greater part of these clay fraction may have been derived from present and ancient Hwangho River. The high concentration of smectite in the northern part near the Cheju and around the Soheugsan Islands, eastern side of Socotra Rock probably result from supplies smectite altered from volcanic materials distributed in the Cheju Island and Socotra Rock, whereas the samples near the Chuja and northern parts of the Cheju Island contain weak calcite peak and high concentration of kaolinite and chlorite which is closely related to the geolgical characteristics on the adjacenting land area.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.19 no.6
• /
• pp.547-557
• /
• 1986

The characteristics of the three alkaline proteinases, Enz. A, B and C, from the pyloric caeca of mackerel have been investigated. The optimum condition for the activity of the Enz. A, B and C was pH 9.4, 9.8 and 9.8 at $45^{\circ}C$ for $2\%$ casein solution, and was pH 9.2 10.2 and 9.8 at $45^{\circ}C$ for $5\%$ hemoglobin denatured by urea, respectively. Enz. A, B and C by heat treatment at $50^{\circ}C$ for 5 min were inactivated 90, 33 and $37\%$, respectively, over the original activity. The reaction rate of the three alkaline proteinases was constant to the reaction time to 40 min in the reaction condition of $2{\mu}g/ml$ of enzyme concentration and $2\%$ casein solution. The reaction rate equation and Km value against casein substrate determined by the method of Lineweaver and Burk were: Enz. A, Y=3.6X and $Km=5.0{\times}10^{-3}\%$; Enz. B, Y=6.0X and $Km=1.0{\times}10^{-3}\%$; Enz. C, Y=4.2X and $Km=3.6{\times}10^{-3}\%$. The three alkaline proteinases were inactivated by $Ag^+$ and $Hg^{2+}$, but activated by $Mn^{2+},\;Sn^{2+}\;and\;Pb^{2+}$, Enz. B and C were remarkably inhibited by the soybean trypsin inhibitor. Molecular weight of Enz. A, B and C determined by SDS-polyacrylamide gel electrophoresis and Sephadex G-100 gel filtration was in the range of $27,500{\pm}2,500,\;20,500{\pm}1,500\;and\;15,250{\pm}250$, respectively.

• Nuclear Engineering and Technology
• /
• v.38 no.2
• /
• pp.163-174
• /
• 2006

The $Ph{\acute{e}}bus$ FP project is an international reactor safety project. Its main objective is to study the release, transport and retention of fission products in a severe accident of a light water reactor (LWR). The FPT4 test was performed with a fuel debris bed geometry, to look at late phase core degradation and the releases of low volatile fission products and actinides. Post Test Analyses results indicate that releases of noble gases (Xe, Kr) and high-volatile fission products (Cs, I) were nearly complete and comparable to those obtained during $Ph{\acute{e}}bus$ tests performed with a fuel bundle geometry (FPT1, FPT2). Volatile fission products such as Mo, Te, Rb, Sb were released significantly as in previous tests. Ba integral release was greater than that observed during FPT1. Release of Ru was comparable to that observed during FPT1 and FPT2. As in other $Ph{\acute{e}}bus$ tests, the Ru distribution suggests Ru volatilization followed by fast redeposition in the fuelled section. The similar release fraction for all lanthanides and fuel elements suggests the released fuel particles deposited onto the plenum surfaces. A blockage by molten material induced a steam by-pass which may explain some of the low releases. The revaporisation testing under different atmospheres (pure steam, $H_2/N_2$ and steam /$H_2$) and up to $1000^{\circ}C$ was performed on samples from the first upper plenum. These showed high releases of Cs for all the atmospheres tested. However, different kinetics of revaporisation were observed depending on the gas composition and temperature. Besides Cs, significant revaporisations of other elements were observed: e.g. Ag under reducing conditions, Cd and Sn in steam-containing atmospheres. Revaporisation of small amounts of fuel was also observed in pure steam atmosphere.

• Resources Recycling
• /
• v.18 no.4
• /
• pp.14-23
• /
• 2009

In terms of resources recycling and resolving waste disposal problems, it is very important to recover precious metals like Au, Ag and Pd and valuable metals like Cu, Sn and Ni from the scraps of waste electrical and electronic equipment(WEEE) that consists of detective electrical and electronic parts discarded during manufacturing electrical and electronic equipments and waste electrical and electronic parts generated during disassembling them. In general, the scraps of WEEE are composed of various metals and alloys as well as refractory oxides and plastic components. Precious and valuable metals from the scraps of WEEE can be recovered by gas-phase-volatilization, hydrometallurgical, or pyrometallurgical processes. However, the gas-phase-volatilization and hydrometallurgical processes have been suggested but not yet commercialized. At the present time, most of the commercial plants for recovering precious and valuable metals from the scraps of WEEE adopt pyrometallurgical processes. Therefore, in this paper, the technical and environmental aspects on the important pyrometallurgical processes through literature survey are reviewed, and the scale-up result of a new pyrometallurgical process for recovering the precious and valuable metals contained in the scraps of WEEE using waste copper slag is presented.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.123-123
• /
• 2012

최근 연구되고 있는 TSV(Through Silicon Via) 기술은 Si 웨이퍼 상에 직접 전기적 연결 통로인 관통홀을 형성하는 방법으로 칩간 연결거리를 최소화 할 수 있으며, 부피의 감소, 연결부 단축에 따른 빠른 신호 전달을 가능하게 한다. 이러한 TSV 기술은 최근의 초경량화와 고집적화로 대표되는 전자제품의 요구를 만족시킬 수 있는 차세대 실장법으로 기대를 모으고 있다. 한편, 납땜 재료의 주 원료인 주석은 주로 반도체 소자의 제조, 반도체 칩과 기판의 접합 및 플립 칩 (Flip Chip) 제조시의 범프 형성 등 반도체용 배선재료에 널리 사용되고 있다. 최근에는 납의 유해성 때문에 대부분의 전자제품은 무연솔더를 이용하여 제조되고 있지만, 주석을 이용한 반도체 소자가 고밀도화, 고 용량화 및 미세피치(Fine Pitch)화 되고 있기 때문에, 반도체 칩의 근방에 배치된 주석으로부터 많은 알파 방사선이 방출되어 메모리 셀의 정보를 유실시키는 소프트 에러 (Soft Error)가 발생되는 위험이 많아지고 있다. 이로 인해, 반도체 소자 및 납땜 재료의 주 원료인 주석의 고순도화가 요구되고 있으며, 특히 알파 방사선의 방출이 낮은 로우알파솔더 (Low Alpha Solder)가 요구되고 있다. 이에 따라 본 연구는 4인치 실리콘 웨이퍼상에 직경 $60{\mu}m$, 깊이 $120{\mu}m$의 비아홀을 형성하고, 비아 홀 내에 기능 박막증착 및 전해도금을 이용하여 전도성 물질인 Cu를 충전한 후 직경 $80{\mu}m$의 로우알파 Sn-1.0Ag-0.5Cu 솔더를 접합 한 후, 접합부 신뢰성 평가를 수행을 위해 고속 전단시험을 실시하였다. 비아 홀 내 미세구조와 범프의 형상 및 전단시험 후 파괴모드의 분석은 FE-SEM (Field Emission Scanning Electron Microscope)을 이용하여 관찰하였다. 연구 결과 비아의 입구 막힘이나 보이드(Void)와 같은 결함 없이 Cu를 충전하였으며, 고속전단의 경우는 전단 속도가 증가할수록 취성파괴가 증가하는 경향을 보였다. 본 연구를 통하여 전해도금을 이용한 비아 홀 내 Cu의 고속 충전 및 로우알파 솔더 볼의 범프 형성이 가능하였으며, 이로 인한 전자제품의 소프트에러의 감소가 기대된다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.19 no.6
• /
• pp.625-635
• /
• 1990

The purpose of this study was focused on investigation of biochemical properties of amylases in germinating corn(Zea mays L.) the amylase(I), (II) and (III) from germinating corn seeds were partially purified by ammonium sulfate precipitation, DEAE-Sephadex A-50 ion exchange column chromatography and Sephadex G-100 gel filtration. The last step was effective for separation of the corn amylases to a homogeneous slate. the purified amylase(I) was identified as a kind of $\alpha$-amylase from the fact that 5％ starch solution was hydrolysed into mainly maltose and maltotetrose by it, and amylase(II) and amylase(III) were enzymes producing maltotetrose as main product. The molecular weight and specific activity of the amylase(I), (II) and (III) were determined to be 54,000 and 70.47 unit/mg, 39,000 and 62.98 unit/mg, and 51,000 and 80.39 unit/mg, respectively. It showed a tendency to increase the amylases activities in presence of Ba, Ca, Co and Fe groups, but inhibits in that of Ag, Sn, Hg and Zn groups, and amylase(I), (II) and (III) remained stable at pH 5-6 and 2$0^{\circ}C$ for 40 days in containing of 1 mM CaCl$_2$. The optimum pH and optimum temperatures were pH 6, pH 5 and pH 6 and 35$^{\circ}C$, 55$^{\circ}C$ and 55$^{\circ}C$, respectively. These results suggest that the amylase(I), (II) and (III) were different amylases.

• Resources Recycling
• /
• v.21 no.2
• /
• pp.3-8
• /
• 2012

In the points of the environmental conservation and the recirculating utilization of limited resources, it is very important to recover valuable metals like Au, Ag, Pd, Cu, Sn, Ni, Co, and Li used as industrial raw materials from urban ores. From now, many processes have been developed for recovering the valuable metals contained in urban ores and some of them have been operated commercially. In the paper, pyrometallurgical processes developed for reclaiming valuable metals from urban ores will be briefly introduced.

• Korean Journal of Materials Research
• /
• v.29 no.11
• /
• pp.720-726
• /
• 2019

Recently, research on cost reduction and efficiency improvement of crystalline silicon(c-Si) photovoltaic(PV) module has been conducted. In order to reduce costs, the thickness of solar cell wafers is becoming thinner. If the thickness of the wafer is reduced, cracking of wafer may occur in high temperature processes during the c-Si PV module manufacturing process. To solve this problem, a low temperature process has been proposed. Conductive paste(CP) is used for low temperature processing; it contains Sn57.6Bi0.4Ag component and can be electrically combined with solar cells and ribbons at a melting point of $150^{\circ}C$. Use of CP in the PV module manufacturing process can minimize cracks of solar cells. When CP is applied to solar cells, the output varies with the amount of CP, and so the optimum amount of CP must be found. In this paper, in order to find the optimal CP application amount, we manufactured several c-Si PV modules with different CP amounts. The amount control of CP is fixed at air pressure (500 kPa) and nozzle diameter 22G(outer diameter 0.72Ø, inner 0.42Ø) of dispenser; only speed is controlled. The c-Si PV module output is measured to analyze the difference according to the amount of CP and analyzed by optical microscope and Alpha-step. As the result, the optimum amount of CP is 0.452 ~ 0.544 g on solar cells.