• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.1
• /
• pp.44-52
• /
• 1996

Influence of frictional and mechanical properties was studied with the content(8-18 wt.%) and shapes(flake of irregular) of graphite that was used as lubricant components of copper-based sintered materials. The density, hardness and bending strength of friction materials with the shape of flake graphite were lower and decreased rapidly than that of irregular, as the content of graphite increases up to 18 wt.%. In friction test, wear rate was about 2.0-$2.5{\times}10^{-7}\textrm{cm}^3$/kgf.m and coefficient of friction was 0.30-0.37, independent on graphite content and shape. As the temperature of friction materials increased, wear rate decreased rapidly because oxides such as $Cu_2O$ and $SnO_2$ in the surface of friction material were formed.

• Journal of Food Hygiene and Safety
• /
• v.26 no.1
• /
• pp.76-81
• /
• 2011

The protease produced by a Bacillus pumilus CN8 strain was purified by DEAE-Cellulose-52 ion exchange. It has a molecular weight of approximately 96,920 Dalton. In the present study, this protease showed strong activity over a broad range of pH (6.5-9.5) and temperature from $40^{\circ}C$ to $60^{\circ}C$, and the protease performed the maximal activity at pH 7.3 at $42^{\circ}C$. The effect of metal ions on protease activity showed that $K^+$ could slightly increase the protease activity, and other ions such as $Zn^{2+}$, $Fe^{2+}$, $Na^+$, $Ca^{2+}$, $Mg^{2+}$ had no significant activation or inhibition to the protease (P> 0.05), and the more important is that $Cu^{2+}$, $Mn^{2+}$, $Sn^{2+}$, $Cd^{2+}$ had a strong inhibitory effect on the protease activity.

• Korean Journal of Veterinary Service
• /
• v.33 no.3
• /
• pp.213-221
• /
• 2010

The results from a total of 412 blood samples consisted of 187 samples from regular visiting group (RV), 94 samples from first visiting group (FV), 52 samples from abandoned group (A), 54 samples from special breeder group (SB), and 25 samples from preliminary breeder group (PB) showed that RV(94.7%) and SB(88.9%) groups had the higher levels of protective antibody, but PB (36.0%) group revealed the lowest level. Among 96 blood samples with lower protective antibody levels, 14 samples (14.6%), 72 samples (75.0%) and 10 samples (10.4%) were below the protective antibody levels to distemper/parvo-virus, distemper only and parvovirus only, respectively. These results implied that antibody to parvovirus was well generated than that to distemper. Eighty six samples (20.9%) showed the protective antibody titer under 1:96 to distemper and 24 samples (5.8%), the protective antibody titer under 1:40 to parvovirus.

• Journal of Ginseng Research
• /
• v.26 no.4
• /
• pp.196-201
• /
• 2002

This study was carried out to compare the contents of saponins and minerals component in Korean Red Ginseng (Heaven, Earth, Good grade), North Korean Red Ginseng (Heaven, Earth, Good grade), Japanese Red Ginseng (Oonju, Sinju 1, 2, 3 grade, respectively) and Chinese Red Ginseng (Seokju, Gilim, 1, 2, 3 grade, respectively). Crude saponin contents were different on according to the grade and cultivation area, and was 3.05-3.76% in Korean Red Ginseng, 2.09-3.21% in North Korean Red Ginseng, 2.82-3.71% in Chinese Seokju Red Ginseng, 2.72-3.62% in Chinese Gilim Red Ginseng, 2.11-2.44% in Japanese Oonju Red Ginseng, 2.18-2.87% in Japanese Sinju Red Ginseng, and the amount of ginsenoside-Rb1, -Re, -Rg$\_$1/ in Korean Red Ginseng were higher than those of North Korean, Chinese and Japanese Red Gingsen. The contents of mineral components were similar, but La, Na and Sn component in Korean Red Ginseng showed the higher amount than those of other Red Ginsengs.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2012.05a
• /
• pp.65-65
• /
• 2012

Copper zinc tin sulfide ($Cu_2ZnSnS_4$, CZTS) is a very promising material as a low cost absorber alternative to other chalcopyrite-type semiconductors based on Ga or In because of the abundant and economical elements. In addition, CZTS has a band-gap energy of 1.4~1.5eV and large absorption coefficient over ${\sim}10^4cm^{-1}$, which is similar to those of $Cu(In,Ga)Se_2$(CIGS) regarded as one of the most successful absorber materials for high efficient solar cell. Most previous works on the fabrication of CZTS thin films were based on the vacuum deposition such as thermal evaporation and RF magnetron sputtering. Although the vacuum deposition has been widely adopted, it is quite expensive and complicated. In this regard, the solution processes such as sol-gel method, nanocrystal dispersion and hybrid slurry method have been developed for easy and cost-effective fabrication of CZTS film. Among these methods, the hybrid slurry method is favorable to make high crystalline and dense absorber layer. However, this method has the demerit using the toxic and explosive hydrazine solvent, which has severe limitation for common use. With these considerations, it is highly desirable to develop a robust, easily scalable and relatively safe solution-based process for the fabrication of a high quality CZTS absorber layer. Here, we demonstrate the fabrication of a high quality CZTS absorber layer with a thickness of 1.5~2.0 ${\mu}m$ and micrometer-scaled grains using two different non-vacuum approaches. The first solution-processing approach includes air-stable non-toxic solvent-based inks in which the commercially available precursor nanoparticles are dispersed in ethanol. Our readily achievable air-stable precursor ink, without the involvement of complex particle synthesis, high toxic solvents, or organic additives, facilitates a convenient method to fabricate a high quality CZTS absorber layer with uniform surface composition and across the film depth when annealed at $530^{\circ}C$. The conversion efficiency and fill factor for the non-toxic ink based solar cells are 5.14% and 52.8%, respectively. The other method is based on the nanocrystal dispersions that are a key ingredient in the deposition of thermally annealed absorber layers. We report a facile synthetic method to produce phase-pure CZTS nanocrystals capped with less toxic and more easily removable ligands. The resulting CZTS nanoparticle dispersion enables us to fabricate uniform, crack-free absorber layer onto Mo-coated soda-lime glass at $500^{\circ}C$, which exhibits a robust and reproducible photovoltaic response. Our simple and less-toxic approach for the fabrication of CZTS layer, reported here, will be the first step in realizing the low-cost solution-processed CZTS solar cell with high efficiency.

• Journal of the Microelectronics and Packaging Society
• /
• v.29 no.2
• /
• pp.49-52
• /
• 2022

As the difficulty of flip chip products increase, interest in stable PKG material technology from the viewpoint of reliability is increasing. Currently, the representative of poor reliability that are mainly occurring in flip chip PKG are Sn bridge and Cu dendrite. Two type defects are caused by void generated by the flux residue around the bump. In order to essentially minimize the risk of this type of reliability failure, the linkage between the composition of Molded Under-fill (MUF) and flux, which is related material, was reviewed. In this study, the correlation between base resin and filler, which is the main component of MUF, and flux, was defined, and the material composition design was carried out by refer to lesson learn. With the current material composition, it was confirmed that moisture absorption reliability 85%/85%/24hrs pass result and void did not occur during destructive analysis, and developed MUF has shown flux immunity improving result in flip Chip PKG. We think this study can be used in yield enhancement of flip chip process and give insights to study in compatibility between MUF and flux.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.10
• /
• pp.1438-1446
• /
• 2011

Palmitoyl-oleoyl-oleoyl (POO) and palmitoyl-oleoyl-palmitoyl triacylglycerol rich fraction (PSL) was obtained from the acetone fractionation of palm stearin. The fatty acid composition (total and positional), tri-acylglycerol species, and solid fat index (SFI) were compared among the blends of natural vegetable fats (sal fat, illipe fat, kokum fat, shea stearin fat, and shea butter) and PSL with different ratios (50:50, 60:40, 65:35, 70:30). In total fatty acid composition of PSL, palmitic, oleic, and linoleic acids were the major fatty acids, whereas in natural vegetable fats stearic and palmitic acids were the major fatty acids. Moreover, oleic acid was a major fatty acid at sn-2 position in sal fat, illipe fat, and kokum fat. The TAG species was analyzed by reversed-phase HPLC, from which the PN value ranged from 46 to 54. When natural vegetable fats and PSL were blended with different ratios, decreasing the amount of PSL resulted in increasing SFI in most cases. Among blends, the SFI of sal fat and PSL were most similar to commercial cocoa butter equivalent (CBE).

• The Journal of Korean Academy of Prosthodontics
• /
• v.23 no.1
• /
• pp.39-59
• /
• 1985

The purpose of this study was to investigate how gap distances of 0.13mm, 0.15mm, 0.20mm, and 0.30mm affects solder joint strength from gold alloys and nickel-chromium base alloys and to examine the composition of solder gold, the solder joint of gold alloys and nickel-chromium base alloys. The tensile test specimens were prepared in the split stainless steel mold with a half dumbbell shape 2.5mm in diameter and l2mm in length. 6 pairs of specimens of each gap distance group of gold alloys and nickel-chromium base alloys were made and 48 pairs of all specimens were soldered with solder gold of 666 fineness. All soldered specimens were machined to a uniform diameter and then a tensile load was applied at a cross-head speed of 0.10mm/min using Instron Universal Testing Machine, Model 1115. The fractured specimens at solder gold of solder joint fracture with each gap distance of 0.13mm, 0.15mm, 0.20mm, and 0.30mm were examined under the Scanning Electron Microscope, JSM-35c and the composition of solder gold, the solder joint of gold alloys and nickel-chromium base alloys was analyzed by Electron Probe Micro Analyzer. The results of this study were obtained as follows: 1. In case of soldering of gold alloys, the tensile strength between gold alloys showed $37.33{\pm}2.52kg/mm^2$ at 0.13, $39.14{\pm}3.35kg/mm^2$ at 0.15mm, $43.76{\pm}2.97kg/mm^2$ at 0.20mm, and $49.18{\pm}4.60kg/mm^2$ at 0.30mm. There was statistically significant difference at each gap distance, and so the greater increase of gap distance showed the greater tensile strength. 2. In case of soldering of nickel-chromium base alloys, the tensile strength between nickel-chromium base alloys showed $34.84{\pm}4.26kg/mm^2$ at 0.13mm, $37.25{\pm}2.49kg/mm^2$ at 0.15mm, $42.91{\pm}4.32kg/mm^2$ at 0.20mm, and $46.93{\pm}4.21kg/mm^2$ at 0.30mm. There was not statistically significant difference only between 0.13mm and 0.15mm and bet ween 0.20 mm and 0.30mm, but generally the greater increase of gap distance showed the greater tensile strength. 3. The greater increase of gap distance shoed less porosities in solder gold at solder joint fracture. 4. In solder gold Au, Cu, Ag, Zn, and Sn were composed and Au and Cu were mostly distributed uniformly. 5. In solder joints of solder gold and gold alloys Au, Cu, Ag, Zn, and Sn were composed in solder gold and Au, Cu, Ag, Pt, and Pd were composed in gold alloys. Au and Cu of solder gold and gold alloys were mostly distributed uniformly and the diffusion of other elements except Pt and Pd around the solder joint was not almost found. In solder joints of solder gold and nickel-chromium base alloys Au, Cu, Ag, Zn, and Sn were composed in solder gold and Ni, Cr, and Al were composed in nickel-chromium base alloys. Au and Cu of solder gold and Ni and Cr of nickel-chromium base alloys were mostly distributed uniformly and the diffusion of other elements except Cr around the solder joint was not almost found.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.1-4
• /
• 2012

Effects of artificial holes on the cooling efficiency of single grain YBCO bulk superconductors were studied. Single grain YBCO bulk superconductors without artificial holes, with six 2.4 mm holes and six holes filled with Bi-Pb-Cd-Sn metal solder were fabricated by a top-seeded melt growth process for powder compacts with/without holes. Simulation for the cooling rate to a liquid nitrogen temperature (77 K) of YBCO samples was carried out using a finite element method (FEM) and the results are compared with the actual cooling rates of samples in liquid nitrogen. The simulated cooling times for the YBCO sample without holes, with six holes and with six holes filled with the metal solder were 80, 47 and 75 sec. respectively, which are similar to the actual cooling times of 84, 52 and 78 sec. estimated for the same samples cooled in liquid nitrogen. The shorter cooling time of the sample with artificial holes are attributed to the increased surface areas associated with the presence of artificial holes. The metal filling into the holes did not give any remarkable effect on the cooling efficiency.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.4
• /
• pp.1070-1080
• /
• 2021

This study is a descriptive survey research on social network service addiction tendency and interpersonal relationships on college life adaptation among nursing students. The study period was from October 1 to 4, 2019, the survey was conducted for 228 first and third year nursing students located in G city. The collected data were analyzed with the SPSS 23.0 program using descriptive statistics, ANOVA, Pearson correlation coefficients, and multiple regression. The results of the study showed that there were differences in the subjects' college life adaptation depending on their gender (t=5.26, p<.001), daily average duration of using social network service (F=8.07, p<.001), and friends in real life (F=2.87, p=.037). College life adaptation had a significant correlation with social network service addiction tendency (r=-.31, p<.001) and interpersonal relationships (r=.52, p<.001), and social network service addiction tendency with interpersonal relationships had a significant correlation (r=-.17, p=.011). Factors that affected college life adaptation included interpersonal relationships (𝛽=.477, p<.001), gender (𝛽=-.198, p=.001), and daily average duration of using social network service (𝛽=-.177, p=.003), and the explanatory power of these factors was 37.8%. Based on the results of this study, it is thought that it is necessary to develop a program for a positive interpersonal relationship formation using social network service in order to improve the college life adaptation of nursing students.