• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.6
• /
• pp.155-163
• /
• 2003

As vehicles become more intelligent for convenience and safety of drivers, the in-vehicle networking(IVN) systems and smart modules are essential components for intelligent vehicles. However, for wider application of smart modules and IVN's, the following two problems should be overcome. Firstly, because it is very difficult that transducer manufacturers developed the smart module that supports all the existing IVN protocols, the smart module must be independent of the type of networking protocols. Secondly, when the smart module needs to be replaced due to its failure, only the transducer should be replaced these without the replacement of the microprocessor and network transceiver. To solve these problems, this paper investigates the feasibility of an IEEE 1451 based smart module. More specifically, a smart module for DC motor control has been developed. The module has been evaluated for its delay caused by the IEEE 1451 architecture. In addition, the time required for transducer replacement has been measured.

• Smart Structures and Systems
• /
• v.1 no.1
• /
• pp.47-61
• /
• 2005

A ring-shaped lead zirconate titanate (PZT) piezoceramic sensor has been integrated with the Langevin-type piezoceramic driver of an ultrasonic wire-bonding transducer to form a smart transducer for in-situ measurement of three essential bonding parameters: namely, impact force, ultrasonic amplitude and bond time. This sensor has an inner diameter, an outer diameter and a thickness of 12.7 mm, 5.1 mm and 0.6 mm, respectively. It has a specifically designed electrode pattern on the two major surfaces perpendicular to its thickness along which polarization is induced. The process-test results have indicated that the sensor not only is sensitive to excessive impact forces exerted on the devices to be bonded but also can track changes in the ultrasonic amplitude proficiently during bonding. Good correlation between the sensor outputs and the bond quality has been established. This smart transducer has good potential to be used in automatic process-control systems for ultrasonic wire bonding.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.168-171
• /
• 2003

As vehicles are more intelligent for convenience and safety of drivers, the in-vehicle networking systems and smart modules are essential components for intelligent vehicles. However, for the smart module to widely apply to the IVN systems, two problems are considered as follows. Firstly, because it is very difficult that transducer manufacturers developed the smart module that supports the existing all IVN protocols, the smart module must be independent to the type of networking protocols. Secondly, when the smart module is exchanged due to its failure, it is necessary how the transducer is only exchanged without exchange of the microprocessor and network transceiver. This paper deals with the IEEE 1451 based smart module that describes the digital interface between a network transceiver and sensor module. Finally. efficiency of the IEEE 1451 based smart module was evaluated on the experimental model.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.44 no.5
• /
• pp.28-37
• /
• 2007

IEEE 1451 standard defines an interface for network and transducer. In this paper, We propose an architectural model to configure data acquisition system and wireless smart sensor node based on IEEE 1451 standard. Proposed Network Capable Application Processor(NCAP) supports the task of data acquisition and communication for smart sensor node and network. The NCAP is able to reconfigure without interrupting the functionality of the wireless sensor node and receives the critical information of transducer using the DB. Smart sensor node is able to provide the basic information of sensor in digital format. This digital format is called Transducer Electronic Data Sheet(TEDS), is capable of plug-and-play capability of wireless sensor node and the NCAP. We simplify the format of TEDS and template to apply to wireless network environment. information of TEDS and template is transmitted using ad-hoc routing. This study system uses body temperature sensor and ECG(Electrocardiogram) sensor to provide the medical information service. The format of template is selected by data sheet of the sensor and reconfigured to accurately describe the property of the sensor. DB of NCAP is possible to register new template and information of the property as developing new sensor.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1564-1567
• /
• 1998

This paper presents a smart thin film pressure transducer which is highly suitable for a precise and remote measurement of pressure and has the following smart functions: automatic zero tracking, automatic span adjustment, temperature compensation, continuous self-diagnostics for faults(open strain gages, abnormal data, incorrect A/D conversion, and overpressure), data memory and multi-drop communication with PC.

• Smart Structures and Systems
• /
• v.8 no.4
• /
• pp.413-431
• /
• 2011

Under the external shearing stress, the external radial stress and the electric potential simultaneously, the piezoelectric hollow cylinder transducer is studied. With the Airy stress function method, the analytical solutions of this transducer are obtained based on the theory of piezo-elasticity. The solutions are compared with the finite element results of Ansys and a good agreement is found. Inherent properties of this piezoelectric cylinder transducer are presented and discussed. It is very helpful for the design of the bearing controllers.

• Smart Structures and Systems
• /
• v.24 no.4
• /
• pp.435-446
• /
• 2019

The existing piezoelectric spherical transducers with fixed prescribed dynamic characteristics limit their application in scenarios with multi-frequency or frequency variation requirement. To address this issue, this work proposes an improved design of piezoelectric spherical transducers using the resistance tuning method. Two piezoceramic shells are the functional elements with one for actuation and the other for tuning through the variation of load resistance. The theoretical model of the proposed design is given based on our previous work. The effects of the resistance, the middle surface radius and the thickness of the epoxy adhesive layer on the dynamic characteristics of the transducer are explored by numerical analysis. The numerical results show that the multi-frequency characteristics of the transducer can be obtained by tuning the resistance, and its electromechanical coupling coefficient can be optimized by a matching resistance. The proposed design and derived theoretical solution are validated by comparing with the literature given special examples as well as an experimental study. The present study demonstrates the feasibility of using the proposed design to realize the multi-frequency characteristics, which is helpful to improve the performance of piezoelectric spherical transducers used in underwater acoustic detection, hydrophones, and the spherical smart aggregate (SSA) used in civil structural health monitoring, enhancing their operation at the multiple working frequencies to meet different application requirements.

• Smart Structures and Systems
• /
• v.21 no.2
• /
• pp.151-161
• /
• 2018

A new type of cascade sandwiched piezoelectric ultrasonic transducer is presented and studied. The cascade transducer is composed of two traditional longitudinally sandwiched piezoelectric transducers, which are connected together in series mechanically and in parallel electrically. Based on the analytical method, the electromechanical equivalent circuit of the cascade transducer is derived and the resonance/anti-resonance frequency equations are obtained. The impedance characteristics and the vibrational modes of the transducer are analyzed. By means of numerical method, the dependency of the resonance/anti-resonance frequency and the effective electromechanical coupling coefficient on the geometrical dimensions of the cascade transducer are studied and some interesting conclusions are obtained. Two prototypes of the cascade transducers are designed and made; the resonance/anti-resonance frequency is measured. It is shown that the analytical resonance/anti-resonance frequencies are in good agreement with the experimental results. It is expected that this kind of cascade transducer can be used in large power and high intensity ultrasonic applications, such as ultrasonic liquid processing, ultrasonic metal machining and ultrasonic welding and soldering.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.2
• /
• pp.176-184
• /
• 2011

As modern megalopolises become more complex and huge, convenience and safety of citizens are main components for a welfare state. In order to make safe society, telemetrics technology, which remotely measures the information of target system using electronic devices, is an essential component. In general, telemetrics technology consists of USN (ubiquitous sensor network) based on a wireless network, smart sensor, and SoC (system on chip). In the smart sensor technology, the following two problems should be overcome. Firstly, because it is very difficult for transducer manufacturers to develop smart sensors that support all the existing network protocols, the smart sensor must be independent of the type of networking protocols. Secondly, smart sensors should be modular so that a faulty sensor element can be replaced without replacing healthy communication element. To solve these problems, this paper investigates the feasibility of an IEEE 1451 based ZigBee smart sensor system. More specifically, a smart sensor for large network coverage has been developed using ZigBee for active telemetrics.

• Smart Structures and Systems
• /
• v.17 no.6
• /
• pp.1055-1065
• /
• 2016

An anisotropic ultrasonic transducer is proposed for Lamb wave applications, such as passive damage or impact localization based on ultrasonic guided wave theory. This transducer is made from a PMNPT single crystal, and has different piezoelectric coefficients $d_{31}$ and $d_{32}$, which are the same for the conventional piezoelectric materials, such as Lead zirconate titanate (PZT). Different piezoelectric coefficients result in directionality of guided wave generated by this transducer, in other words, it is an anisotropic ultrasonic transducer. And thus, it has different sensitivity in comparison with conventional ultrasonic transducer. The anisotropic one can provide more information related to the direction when it is used as sensors. This paper first shows its detailed properties, including analytical formulae and finite elements simulations. Then, its application is described.