• Journal of Environmental Science International
• /
• v.11 no.12
• /
• pp.1217-1226
• /
• 2002

This study aims at the effective estimation of water supply capacity of small scale reservoir and the proposal of the data which is necessary to establish the water resources management plan of down stream area of the reservoir in the future by comparison and examination about reservoir operation technique for the security of agricultural water in small scale reservoir. The result of flow calculation by Tank model is used for the input data as the inflow data which is needed for the analysis of water supply capacity. Stochastic method, simulation method, and optimization method are used to examine the water supply capacity, and water security amount is compared with each method. From the analyses of water supply capacities by each method, slightly different results are shown in spite of the effort to compare them equally using input data such as inflow data under equal conditions, and the comparison of water supply capacities by each method are as follows; linear planning method, simulation method, and transition probability matrix method in the order of amount from the largest. It is thought that the simulation method in which comparatively reasonable application of the inflow data is possible and is simulated in successive time series dam operation of the three methods used in this study thus, simulation model is proper to estimate the water supply capacity of agricultural small scale reservoir. And it is judged that the heightening of efficiency of water resources utilization according to the development of downstream area of dam may be possible using the upward readjusted water supply amount of $55.18{\tiems}10^6ton$ and $63.7{\times}10^6ton$ at 95% and 90% supply reliability respectively which are above the planning water supply amount of $50.0{\times}10^6$ton when the simulation method is introduced as the standard.

• Journal of the Korean association of regional geographers
• /
• v.14 no.2
• /
• pp.173-188
• /
• 2008

In order to make comparative analysis of geomorphological changes caused by urban development, I surveyed the distribution of geomorphological resources of 'Daegu Innovation Town' development plan area. The results are as follow: (1) At the front of small valleys of back-mountains are formed small alluvial fans, and at the side of small valleys are distributed hills connected with back-mountains. (2) As small valley erode laterally hills, vertical bluffs and planner bedrock riverbed are formed, and in some riverbed are appeared mud cracks and ripple marks. (3) The depth of valley in alluvial fan of 'Sinseo District' is 7m. In Sinseocheon valley dissecting alluvial fan, fluvial terraces 2m high above riverbed are distributed. Those terraces were formed while alluvial fan was dissected after last glacial period.

• Journal of the Korea Institute of Building Construction
• /
• v.10 no.1
• /
• pp.213-219
• /
• 2010

The research, based on 200 cases of small interior works in6 different floor area types of apartment in Busan, intended to compare the architectural work with the breakdown structure and analyze the cost of general small-scale interior work, by work type. The outcome of the research is outlined as follows. (1) Given the cost of small interior works for apartmentsranges from 10 million to 15 million won, which correspond to apartments ranging in size from $79.2m^2$ (24PY) to $105.6m^2$, it is necessary to implement a cost analysis for material cost and labor cost for these two types. (2) Given that small interior work for apartments comprises mostly finishing work, unlike the categoriesof general architectural work, it is more reasonable to classify the works into 9 categories,which include embellishment, wood, tile, paint, metal, toilet, sink & furniture, electric & mechanical and other works, instead of the 22 divisions stipulated in the Korean Architectural Standard Specification. (3) After reviewing the average cost of small interior work and rate by floor area, it was found thatthe average cost of 24PY was 10.5 million won, of which metal work accounts for 12.8%, embellishment work 17.8%, and toilet 19.7%, while sink & furniture appeared to be the highest with 22.1%, while for 32PY, average cost was 12.5 million won,which comprises 7.4% wood work, sink & furniture 20.2%, toilet 23.4% and embellishment work the highest at 28.6%, indicating that embellishment work accounts for the greater portion.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2004.04a
• /
• pp.51-55
• /
• 2004

In this study, the levelling and the GPS levelling were carried out with 6 points in 2km${\times}$2km area and the results were analysed. As a result of this research, we had to observe more than 15 minutes to get the height accuracy of 10mm by single frequency GPS receiver in relative surveying. We could not get more better accuracy than 10mm. we could get the height accuracy of within 10mm from observing only more than 5 minutes by double frequency GPS receiver, and of within about 3mm from observing more than 10 minutes. When the number of fixed points is within 3, the level net adjustment result is very close to the one of direct levelling survey. When the number of fixed points is 3, the less the area of triangle the better the adjustment result, and the case of including measure point has more better accuracy than that of non-including measure point.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.353-364
• /
• 2011

This paper presents the ground behaviour of shield TBM lunching area during excavation. In order to perform this study, a scaled model test was carried out in the 1/45 scale for a field tunnel in practice where the tunnel had about 7.8 m diameter at Seoul Metro Line 9 construction site. The test to simulate earth pressure balance (EPB) shield TBM tunnelling at the lunching area was conducted with the developed small scaled shield TBM machine. Measurements were performed during simulation of excavation for total jacking thrust force, ground displacements and pressures. Based on the analysis of simulation results, the stability of ground was verified and evaluated. In particular, the suitable reinforcement range and methods are also suggested. In addition, these results are useful for engineers and technicians to select suitable and serviceable machine operation parameters and reduce environmental influence at all stages of tunnel construction.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.09a
• /
• pp.698-707
• /
• 2010

Because of localized extreme rainfall followed by Typhoon Ewiniar in 2006, a lot of landslides and debris flows were occurred in Jinbu area of Gangwon Province. Field investigation performed in this area found that it can be divided into three categories i.e. large debris flow, small debris flow, and debris flow around forest road. We performed field investigation especially for the sites where debris flow occurred around forest road. And the characteristics of the debris flow around forest road were analyzed and compared with the other site of debris flow.

• Journal of the Korean Institute of Rural Architecture
• /
• v.4 no.2
• /
• pp.39-48
• /
• 2002

The purpose of this study was to analyze and explain the formation and characteristics of wooden church architecture in Andong area from 1902 to 1975. Especially, I tried to find out the characteristic of wooden construction and the influence of typical form of Andong church architecture to the small church of nearby Andong rural area. This study was carried out the actual inspection of existing architecture through analysis.

• Structural Engineering and Mechanics
• /
• v.3 no.6
• /
• pp.569-581
• /
• 1995

In this paper, the seismic behavior of a 10-story building equipped with viscoelastic dampers is analyzed. The effects of ambient temperature, the thickness, the total area, and the position of the viscoelastic dampers are studied. Results indicate that the energy-absorbing capacity of viscoelastic damper decreases with increasing the ambient temperature. The thickness and the total area of viscoelastic dampers also affect the seismic mitigation capacity. The thickness cannot be too small, which is not effective in vibration reduction, nor can it be too large, which not only increases the cost but also reduces the seismic resistance. The total area of viscoelastic dampers should be determined properly for optimum damper performance at the most economical design. The mounting position of viscoelastic dampers also influences the structure's seismic performance. Numerical results show that, if properly equipped, the VE dampers can reduce the structural response both floor displacement and story shear force and increase the overall level of damping in structures during earthquakes.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.1-15
• /
• 1995

The driving patterns in Seoul metropolitan area were surveyed in an experiment involving 1,212km of driving along seventeen representative routes. The speed and fuel consumption data were recorded and the influence of driving patterns on vehicle fuel economy was analyzed by statistical techniques. The results showed that characteristics of driving in Seoul metropolitan area are far different from that of CVS-75 mode and then on-road fuel economy in Seoul may be small as compared with that of CVS-75 mode. Finally, it was proposed that CVS-75 mode fuel economy should be modified by applying adjustment factor to represent actual on-road fuel economy.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.6 no.1
• /
• pp.48-54
• /
• 2011

As personal or compact devices with image acquisition functionality are becoming easily available for common users, the voluminous images that need to be managed by image related services or systems demand efficient and effective methods in the perspective of image identification. The objective of image identification is to associate an image with a unique identifier. Moreover, whenever an image identifier needs to be regenerated, the newly generated identifier should be consistent. In this paper, we propose three image identifier generation methods utilizing image features: linear component, luminance area, and combination of both features. The linear component based method exploits the information of distribution of partial lines over an image, while the luminance area based method utilizes the partition of an image into a number of small areas according to the same luminance degree. The third method is proposed in order to take advantage of both former methods. In this paper, we also demonstrate the experimental evaluations for uniqueness and similarity analysis that have shown favorable results.