• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.5
• /
• pp.389-398
• /
• 2019

In this paper, we propose a method to detect small unmanned aerial vehicles(UAVs) flying in a real-world environment. Small UAV signals are frequently obscured by clutter signals because UAVs usually fly at low altitudes over urban or mountainous terrain. Therefore, to obtain a desirable detection performance, clutter signals must be considered in addition to noise, and thus, a performance analysis of each clutter removal technique is required. The proposed detection process uses clutter removal and pulse integration methods to suppress clutter and noise signals, and then detects small UAVs by utilizing a constant false alarm rate detector. After applying three clutter removal techniques, we analyzed the performance of each technique in detecting small UAVs. Based on experimental data acquired in a real-world outdoor environment, we found it was possible to derive a clutter removal method suitable for the detection of small UAVs.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.1
• /
• pp.1-12
• /
• 2022

Wind tunnel test for a small scale electric ducted fan with a 104mm diameter was conducted to analyze the aerodynamic characteristics when it was used as a propulsion system of tilt-propeller UAV. Experimental conditions were derived from flight conditions of a sub-scaled OPPAV. Forces and moments of the ducted fan model were measured by a 6-axis balance and 3-dimensional wake vectors which could induce an aerodynamic influence in the vehicle were measured by 5-hole probes. Thrust and torque on hover and cruise conditions were measured and analyzed to drive out the operating conditions when it was applied in the sub-scaled OPPAV. On transition conditions, thrust keep its value with tilt angle variation below 40° and increase after that. But, sideforce increase constantly until 75°. The maximum axial velocity in the wake on hover and cruise conditions was around 60m/s and tangential velocity was around 12m/s. The position of the maximum axial velocity and vortex center move off the fan rotation center line as the tilt angle increases.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.8
• /
• pp.56-64
• /
• 2005

It is prerequisite that we have to fomulate the nonlinear mathematical modeling to design the guidance and control system of rotorcraft-based unmanned aerial vehicle using a small-scaled commercial helicopter. The small-scaled helicopters are very different from the full-scale helicopters in dynamic behavior such as high rotation speed and high frequency dynamic characteristics. In this paper, the formulation of the mathematical model of the small-scaled helicopter to minimize the complexity is presented by component and source build-up approach. It is linearized at the trim condition of hovering and forward flight and analyzed the flight modes. The results of this approach have general trends but a little difference. To verify this approach, it is necessary to compare this theoretical model with experimental results by system identification using flight test as a next research topic.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.101-104
• /
• 2010

Recently, needs for UAVs and small aircraft and small turbo jet or turbo fan engines for these air-crafts are increasing. Size and weight are the two main restrictions in small air-crafts such as UAV or VLJ propulsion system applications. Therefore, high power density is required in small size and designers come up with unconventional solutions in the design of small aero gas turbine engines. One of the solutions is the usage of highly loaded axial compressors. This paper introduces an aerodynamic design method of a highly loaded axial compressor and its review process. Numerical simulation has been carried out to assess the aerodynamic performance of the compressor.

• Journal of Biosystems Engineering
• /
• v.31 no.2 s.115
• /
• pp.95-101
• /
• 2006

Present chemical application system using a power sprayer has been a labor intensive, ineffective and shirking task in farming. Therefore, a small RF controlled (unmanned) helicopter was suggested to replace the conventional spray system. The aerial application using the unmanned helicopter has been already utilized in Japan, where total area applied up to 704,000 ha in 2005. In this article, the status and cost analysis on the unmanned agricultural helicopter were studied. The aerial application using the agricultural helicopter helps precise and timely spraying and reduces labor intensity and pollution. The field capacity of the helicopter was found to be 60-70 ha a day. The break even point was estimated near the operating area of 750 ha annum. The development of an agricultural helicopter was necessary for taking advantages of both technique and economy.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.23 no.2
• /
• pp.51-56
• /
• 2015

This paper presents the procedure of drag prediction for EAV-1, based on a numerical analysis correlated to an in-flight test. EAV-1, developed by Korea Aerospace Research Institute, is a small-sized UAV to test a hydrogen-fuel cell power system. The long-endurance test flight of 4.5 hours provides numerous in-flight data. The thrust and drag of EAV-1 during the flight test are estimated based on the wind-tunnel test results for EAV-1's propeller performance. In addition, the CFD analysis using a commercial Navier-Stokes code is carried out for the full-scale EAV-1. The computational result suggests that the initial CFD analysis substantially under-predicts the in-flight drag in that the discrepancy is up to 27.6%. Therefore, additional investigation for more accurate drag prediction is performed; the effect of propeller slipstream is included in the CFD analysis through "fan disk" modelling. Also, the additional drag from airplane trim and load factor that actually exists during the flight test in a circular path is considered. These supplemental analyses for drag prediction turn out to be effective since the drag discrepancy reduces to 2.3%.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.395-398
• /
• 2009

Currently, a new generation of ducted fan UAVs (Unmanned Aerial Vehicles) is under development for a wide range of inspection, investigation and combat missions as well as for a variety of civil roles like traffic monitoring, meteorological studies, hazard mitigation etc. The current study presents extensive results obtained experimentally in order to investigate the tip clearance effects on performance characteristics of a ducted fan for small UAV systems. Three ducted fans having different tip clearance gap and with same rotor size were examined under three different yawed conditions of calibrated slanted hot-wire probe. Three dimensional velocity flow fields were measured from hub to tip at outlet of the ducted fan. The analysis of data were done by PLEAT (Phase locked Ensemble Averaging Technique) and three non-linear differential equations were solved simultaneously by using Newton -Rhapson numerical method. Flow field characteristics such as tip vortex and secondary flow were confirmed through axial, radial and tangential velocity contour plots. At the same time, the effects of tip clearance on axial thrust and input power were also investigated by using wind tunnel measurement system. For enhancing the performance of ducted fan, tip clearance level should be as small as possible.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.3
• /
• pp.73-79
• /
• 2010

A preliminary study on a length-variable rotor blade for a small unmanned helicopter has been conducted. After surveys on previous researches, and examining requirements for application to a small unmanned helicopter, a length-variable rotor blade was designed and manufactured to be driven by centrifugal force from rotor revolution with no mechanical actuator. The rotor blade was divided into a fixed inboard section and an outboard section sliding in span-wise direction. In order to determine the operating conditions of the length-variable rotor during revolution, and to derive the design variables of extension spring and rotor weight, a series of analyses from multi-body dynamics solution were conducted. The manufactured prototype was verified of its length-varying mechanism from a rotor stand, the results and required future improvements are discussed.

• Telecommunications review
• /
• v.24 no.4
• /
• pp.468-480
• /
• 2014

The current-generation avionics systems are based on a federated architecture, where an electronic device runs a single software module or application that collaborates with other devices through a network. This architecture makes the internal system architecture very complicate, and gives rise to issues of Size, Weight, and Power (SWaP). In this paper, we show that the partitioning defined by ARINC 653 can efficiently deal with the SWaP issues on small unmanned aerial vehicles, where the SWaP issues are extremely severe. We especially install the integrated mission system on real hexacopter and quadcopter and perform successful flight tests. The presented software technology for integrated mission system and software consolidation methodology can provide a valuable reference for other SWaP sensitive real-time systems.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.1
• /
• pp.10-16
• /
• 2013

This paper discussed a procedure for noise certification of Aircraft and predicting the full scale over-flight noise of propeller from acoustic wind tunnel measurement of small scale propeller. Noise Certification Procedures is established from International Civil Aviation Organization(ICAO). The data manipulations are then discussed in extrapolation to simulation flight distance and flight simulation. One of the most important point of flight simulation is adjustments for differences between wind tunnel test conditions and flight test conditions. To simulated the noise level estimation procedure for noise data post-process, simulate procedures from data of the wind tunnel noise measurement and the flight noise measurement by using a 7kg degree UAV. This study confirmed an effectively noise estimation procedures by wind tunnel noise test and flight noise test.