• Computers and Concrete
• /
• 제20권2호
• /
• pp.145-154
• /
• 2017

In geological engineering, grouting with Portland cement is a common technique for ground improvement, during which micro-fine cement is applied as a slurry, such that it intrudes into soil voids and decreases soil porosity. To determine the utility and behavior of cements with different Blaine values (index of cement particle fineness) for stabilization of fine sand, non-destructive and destructive tests were employed, such as laser-ray determination of grain size distribution, and sedimentation, permeability, and compressive strength tests. The results of the experimental study demonstrated a suitable mix design for the upper and lower regions of the cement-grading curve that are important for grouting and stabilization. Increasing the fineness of the cement decreased the permeability and increased the compressive strength of grouted sand samples considerably after two weeks. Moreover, relative to finer (higher Blaine value) or coarser (lower Blaine value) cements, cement with a Blaine value of $5,100cm^2/g$ was optimal for void reduction in a grouted soil mass. Overall, study results indicate that cement with an optimum Blaine value can be used to satisfy the designed geotechnical criteria.

• 한국재료학회지
• /
• 제9권7호
• /
• pp.675-679
• /
• 1999

$PdCl_2$를 촉매제로 사용한 수소환원분위기에서 $Co(OH)_2$ 로부터 약 400nm크기인 구형의 코발트분말 제조에 관한 연구를 수행하였다. 본 실험에서 코발트의 환원반응속도는 표면반응 코어모델식에 잘 일치하였으며 이때 활성화 에너지는 $145~195^{\circ}C$에서 약 55.6KJ/mol 이었다. 또한 코발트의 환원속도는 초기 수소분압의 0.63승에 비례하는 가스화학흡착반응식으로 표시할 수 있다.

• 한국주조공학회지
• /
• 제13권4호
• /
• pp.359-368
• /
• 1993

Mg-9wt.%Al and Mg-9wt.%-1.6wt%Zn/SiCp(particle size $40{\mu}m$) metal-matrix-composite specimens were manufactured by rheo-compocasting method, known for its effect of improving the wettability. The ceramic reinforcement particles(SiCp) were dispersed in the semi-solid magnesium alloy matrix slurry being vigorously stirred in a high frequency induction furnace under inert atmosphere. A microstructural study of the dispersed particles in the specimens, prepared under different conditions as regards the time(10min, 20min, 30min) and temperature of the stirring, was made with the aid of optical microscope and SEM. The effect of superheating was also observed. It is revealed that 30 minutes' stirring time of the semi-solid at 40% solid fraction temperature(Mg-9wt.%Al : $590^{\circ}C$, AZ91 : $576^{\circ}C$), as determined by the lever rule, gives a satisfactorily uniform distribution of the particles. The superheating is observed to enhance further the uniformity.

• 한국주조공학회지
• /
• 제15권5호
• /
• pp.483-493
• /
• 1995

The microstructural changes during semi-solid state processing of hypereutectic Al-Si alloy has been investigated in the present study. Stirring of semi-solid slurry results in the morphological changes of the primary Si particles, i.e. from angular rod shape to near-spherical shape. Besides the spherodization of primary Si particles, the average particle size increases, especially, at much higher rate in the final stage than that in the early stage of stirring. Various microstructure characterization techniques, such as anisotropic etching, SEM imaging and ECP analysis, reveal that the spherodization of primary Si particles occurs by the combinations of the mechanisms of coalescence, fracture, and wear of the individual particles. Isothermal shearing of hypereutectic Al-Si at $580^{\circ}C$ shows that spherical ${\alpha}-Al$ particles are formed by the dissociation of Al-Si eutectic structure at the early stage of isothermal shearing. The spherical ${\alpha}-Al$ particles gradually grow by the mechanisms of Ostwald ripening and coalescence of the particles.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 춘계 학술발표회
• /
• pp.1183-1189
• /
• 2009

The sedimentation rate of particles in a suspension is a function of particle size, initial slurry water content and salinity. Many researches conducted on the behavior of dredged soils have centered on such factors. However, there have been few attempts to assess another important influence factor of seasonal water temperature on designing the placement of dredged materials. In this paper, the effect of seasonal water temperature on sedimentation characteristics of dredged clay was investigated with consideration of three different water temperatures, that are $5^{\circ}C$, $15^{\circ}C$, $35^{\circ}C$, which represent critical water temperatures in winter, spring or fall, and summer, respectively. A series of experimental results reveal that the sedimentation rates for the water temperature of $15^{\circ}C$ and $35^{\circ}C$ are very similar each other, but that of $5^{\circ}C$ that represents a winter season leads to a considerably delayed sedimentation compared to the others. This may be attributable to the retardation of ion-leaching from clay particles at low water temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.275-276
• /
• 2008

통신기기가 고주파수화 함에 따라서 저유전 저손실 재료의 필요성이 증대되고 있으며, 세라믹/폴리머 복합재료를 고주파 회로 기판 소재로 이용하려는 관심이 증폭되고 있다. 본 연구에서는 저손실, 저유전율 특성을 구현하기 위해 $SiO_2$를 세라믹 필러로 복합물을 제작하였다. 평균 입자 크기가 16nm, $2.3{\mu}m$의 fumed 실리카와 평균 입자 크기 $1{\mu}m$, $4{\mu}m$의 fused 실리카를 사용하였다. 이 4종류 실리카를 사용하여 slurry를 제작하고 이를 활용하여 tape을 제작하였다. 제작된 복합체 tape을 적층하여 기판을 제작해 기판의 유전특성을 측정하였다. fumed 실리카의 경우 $SiO_2$ 10vol%이상에서는 균일한 tape성형이 어려워졌으며, 유전 손실이 fused 실리카와 비교하였을 때 큰 폭으로 증가하였다. fumed silica, fused silica 두 종류 모두 입도가 증가하면 유전손실이 증가하였다.

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.575-583
• /
• 2014

The flue gas desulfurization (FGD) process is currently the most effective process utilized to remove sulfur dioxide from stack gases of coal-fired plants. However, FGD systems use a lot of limestone as desulfurizing agent. In this study, we use limestone sludge, which is a by-product of the steel industry, to replace the desulfurizing agent of the FGD system. The limestone particle size is found to be unrelated to the desulfurizing rate; the gypsum purity, however, is related. Limestone sludge mixes with limestone slurry delivered at a constant rate in a desulfurizing agent with organic acid are expected to lead to a high desulfurization efficiency and high quality by-product (gypsum).

• 한국토양비료학회지
• /
• 제44권3호
• /
• pp.415-424
• /
• 2011

This research was conducted to verified the effectiveness of a sintered porous media coated with organic matter as nutrient source and microorganisms as decomposer effective in TPH decomposition for a closed-typed biopole system. The organic matter content in the sintered porous media which was developed with bentonite increased with increasing dilution ratio of pig slurry and the sintered porous media as well as decrease in the particle size of sintered porous media. The decomposition rate of TPH was significantly increased with increasing aeration than that under atmospheric condition. Also the sintered porous media containing organic matter and microorganisms proved that the decomposition was enhanced with addition of nutrients sources in addition to aeration periodically.

• 한국분말재료학회지
• /
• 제27권6호
• /
• pp.484-489
• /
• 2020

In this study, acoustic and viscosity data are collected in real time during the ball milling process and analyzed for correlation. After fast Fourier transformation (FFT) of the acoustic data, changes in the signals are observed as a function of the milling time. To analyze this quantitatively, the frequency band is divided into 1 kHz ranges to obtain an integral value. The integrated values in the 2-3 kHz range of the frequency band decrease linearly, confirming that they have a high correlation with changes in viscosity. The experiment is repeated four times to ensure the reproducibility of the data. The results of this study show that it is possible to estimate changes in slurry properties, such as viscosity and particle size, during the ball milling process using an acoustic signal.

• 청정기술
• /
• 제16권2호
• /
• pp.124-131
• /
• 2010

슬러리 기포탑을 이용하여 수산화칼슘 농도(0.16~0.64 wt%), 계면활성제 농도(2~16 wt%), 총 부피유량(3~6 L/min) 및 $CO_2$ 유량의 부피분율(0.3~0.6)이 탄산칼슘의 morphology, 결정구조, 입자의 크기, 입자 간의 응집화, 비표면적에 미치는 영향을 알아보았다. 실험에 사용한 반응기는 높이가 1.0 m이고 직경이 0.11m, 그리고 중앙에는 직경 4 cm인 튜브가 들어있는 슬러리 기포탑이다. 실험에 사용한 음이온 계면활성제 Dispex N40은 탄산칼슘 합성에 있어 반응 속도에 영향을 주어 반응 종결 시간을 감소시켰다. Dispex N40의 농도가 2 wt%일 때 수산화칼슘의 포화농도인 0.16 wt%에서 이산화탄소의 유량에 따른 침강성 탄산칼슘의 morphology를 살펴보면 반응 속도가 증가할수록 결정의 형태는 단일 결정으로 존재하는 입자들이 많아졌다. Dispex N40은 탄산칼슘의 crystal의 성장과 입자와 입자간의 응집 현상에 영향을 주어 탄산칼슘의 평균 입도를 변화시켰다. 또한 $0.9 L/min\;CO_2$ 유량에서 수산화칼슘의 농도가 0.64 wt%일 때 2 wt%의 계면활성제 첨가로 인해 비표면적을 $35m^2/g$에서 $44m^2/g$로 크게 증가시켰다.