• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.9A
• /
• pp.656-663
• /
• 2009

In 3GPP LTE system downlink, PSS (primary synchronization signal) and SSS (secondary synchronization signal) sequences are used for initial cell search and synchronization. UE (user equipment) detects slot timing, frequency offset, and cell ID by using PSS. After that it should detect frame timing, cell group ID, and CP length by using SSS. But in 3GPP LTE, there are two kinds of CP length, so we should operate FFT twice. In this paper, to minimize SSS detection complexity in cell searcher, we propose a CP length pre-decision algorithm that reduces the arithmetical complexity by half at most, with negligible performance degradation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.8
• /
• pp.1963-1970
• /
• 1998

In this paper, a two-dimensional slotline coupling structure is proposed for the planar active phased array antenna system with scanning the beam by coupled oscillators without phase shifters. The operating characteristics are analyzed and experimentally demonstrated. The proposed two-dimensional slotline coupling structure consists of $|{=}|$-type slotline in the ground plane for the coupling of E-plane and H-plane. From the simulation results of coupling strength with the variation of width, length and the number of slotlines, the optimal coupling structure is proposed and applied to $2{\times}5$ elements of planear phased array antenna. The experimental results show that the beamwidth of E-plane and H-pland are $42^{\circ}$ and $15^{\circ}$, respectivly, and the scanning range is from $-20^{\circ}$ to $15^{\circ}$ from the broadside. Therefore, it is shown the two-dimensional slotline coupling structure for oscillator-type active phased array antenna can be applied to the planar phased array antenna system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.5
• /
• pp.950-956
• /
• 2015

In this paper, a WiMedia Distributed-MAC (D-MAC) protocol is adopted for development of a seamless N-screen wireless service in Indoor and Ship Area Networks. Furthermore, to provide the OSMU (One Source Multi Use) N-screen service through P2P streaming in the seamless D-MAC protocol, a ATMT (Asynchronous Traffic Multi-hop Transmission) technology is proposed and analyzed. In this system, a WiMedia ATMT D-MAC bridge transmits control and managing information to various sensors and instruments, from a central integrated ship area network station. For this technology, a time slot allocation scheme for WiMedia asynchronous traffic and a multi-hop resource reservation scheme are combined to evaluate the performance of each scheme. From simulation results, the proposed ATMT scheme enhances performances in viewpoints of N-screen asynchronous data latency and throughput, compared to the conventional WiMedia D-MAC system.

• The korean journal of orthodontics
• /
• v.49 no.2
• /
• pp.73-80
• /
• 2019

Objective: The purpose of this study was to compare the static (SFF) and kinetic frictional forces (KFF) of a computer-aided design and computer-aided manufacturing lingual bracket (CAD/CAM-LB) with those of conventional LB (Con-LB) and Con-LB with narrow bracket width (Con-LB-NBW) under 3 tooth displacement conditions. Methods: The samples were divided into 9 groups according to combinations of 3 LB types (CAD/CAM-LB [Incognito], Con-LB [7th Generation, 7G], and Con-LB-NBW [STb]) with 3 displacement conditions (no displacement [control], maxillary right lateral incisor with 1-mm palatal displacement [MXLI-PD], and maxillary right canine with 1-mm gingival displacement [MXC-GD]; n = 6/group). While drawing a 0.016-inch copper or super-elastic nickel-titanium archwire with 0.5 mm/min for 5 minutes in a chamber maintained at $36.5^{\circ}C$, SFF and KFF were measured. The Kruskal-Wallis method with Bonferroni correction was performed. Results: The Incognito group demonstrated the highest SFF, followed by the 7G and STb groups ([STb-control, STb-MXLI-PD, Stb-MXC-GD] < [7G-MXC-GD, 7G-MXLI-PD, 7G-control] < [Incognito-MXLI-PD, Incognito-control, Incognito-MXC-GD]; p < 0.001). However, there were no significant differences in SFF among the 3 displacement conditions within each bracket group. Within each displacement condition, the Incognito group demonstrated the highest KFF, followed by the 7G and STb groups ([STb-control, STb-MXLI-PD] < Stb-MXC-GD < 7G-MXLI-PD < [7G-control, 7G-MXC-GD] < [7G-MXC-GD, Incognito-MXLI-PD, Incognito-control] < [Incognito-control, Incognito-MXC-GD]; p < 0.001). MXC-GD exhibited higher KFFs than MXLI-PD in the same bracket group. Conclusions: The slot design and ligation method of the CAD/CAM-LB system should be modified to reduce SFF and KFF during the leveling/alignment stage.

• Journal of Digital Contents Society
• /
• v.10 no.1
• /
• pp.61-71
• /
• 2009

While the broadband network and multimedia technology are being developed, the commercial market on digital contents as well as IPTV has been widely spreading. Especially IPTV is providing various useful services since it makes using multimedia contents easier and more convenient by combining the strong points of both TV and PC system. Until now, IPTV system has been focused on VoD service as a general usages. However, various IPTV services are recently demanded since they can have special features for some specific places and occasions. So in this paper, we propose a design of the download based IPTV system using user-specific channel management. At first, program contents previously scheduled by users are downloaded and are played at settop-box according to the prescribed time table. This system has some advantages of giving users easy access to any wanted media contents in anytime that is IPTV's characteristics. And we can increase stability of services by using time slot distributed download for contents. Because this service can be constructed and maintained at relatively low cost, we confirm that this service model is more suitable to some companies with small infrastructure and special purposes. Accordingly, in this paper, we look into necessary elements and define some protocols for system in order to help other developer build this system.

• Journal of Animal Environmental Science
• /
• v.10 no.1
• /
• pp.23-28
• /
• 2004

This study was conducted to improve a ventilation system on the enclosed farrowing-nursery pig house in Korean swine facilities. This survey ventilation system types four major structures. The first structure has planer slot inlet, where air comes in, and these are placed outside the wall under the eave. Then the air from the pig house flows out through the chimney outlet operated by an exhaust fan(V1). The second structure has an air input through the perforated ceiling inlet, then the air from the pig house flows out through the chimney outlet operated by an exhaust fan(V2). Through the circular duct inlet placed inside the juncture of the entry wall, air also comes in(third structure). Then, air from the pig house flows out through the chimney outlet operated by an exhaust fan(V3), Similarly, air comes in through the circular duct inlet placed inside the juncture of the entry wall, but air from the pig house flows out through the side wall by an exhaust fan(V4). Temperature, relative humidity, air velocity and ammonia concentration(NH$_3$) were measured in the interior farrowing-nursery pig house during winter. The results were as follows; Interior temperature at the pig house was not remarkably different in all ventilation systems. The V4 system had low area air velocity, and this was better than other systems. It also had a lower ammonia concentration than other systems. V3 and V4 systems had stable airflow patterns, better than other systems. Therefore, it is suggested that the V3 and V4 ventilation system be applied in the enclosed farrowing-nursery pig house in winter.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.12
• /
• pp.108-116
• /
• 2009

In this paper, we propose a Ethernet based audio distribution system with a new L1/L2 hybrid switching scheme, and evaluate its performance. The proposed scheme not only offers guaranteed low latency and jitter characteristics that are essentially required for the distribution of high-quality uncompressed audio traffic, and but also provide an efficient transmission of data traffic on the Ethernet environment. The audio distribution system with a proposed scheme consists of a master node and a number of relay nodes, and all nodes are mutually connected as a daisy-chain topology through up and downlinks. The master node generates an audio frame for each cycle of 125us, and the audio frame has 24 time slotted audio channels for carrying stereo 24 channels of 16-bit PCM sampled audio. On receiving the audio frame from its upstream node via the downlink, each intermediate node inserts its audio traffic to the reserved time slot for itself, then relays again to next node through its physical layer(L1) transmission - repeating. After reaching the end node, the audio frame is loopbacked through the uplink. On repeating through the uplink, each node makes a copy of audio slot that node has to receive, then play the audio. When the audio transmission is completed, each node works as a normal L2 switch, thus data frames are switched during the remaining period. For supporting this L1/L2 hybrid switching capability, we insert a glue logic for parsing and multiplexing audio and data frames at MII(Media Independent Interlace) between the physical and data link layers. The proposed scheme can provide a good delay performance and transmission efficiency than legacy Ethernet based audio distribution systems. For verifying the feasibility of the proposed L1/L2 hybrid switching scheme, we use OMNeT++ as a simulation tool with various parameters. From the simulation results, one can find that the proposed scheme can provides outstanding characteristics in terms of both jitter characteristic for audio traffic and transmission efficiency of data traffics.

• Journal of the Korean Society for Railway
• /
• v.15 no.4
• /
• pp.370-375
• /
• 2012

In order to apply Interior Permanet Magnet Synchronous Motor(IPMSM) to the propulsion system of the railway transit, 110kW class IPMSMs with high-power density are designed as a concentrated winding model and a distributed winding model in this study. The concentrated winding model designed in this study is 6 poles/9 slots and the distributed winding model is 6 poles/36 slots. In general, the eddy current losses in the permanent magnets of IPMSM are caused by the slot harmonics. The thermal demagnetization of the magnet by the eddy current losses at high rotational speed often becomes one of the major problems in the IPMSM with a concentrated windings especially. A design to reduce eddy current losses in permanent magnet design is important in IPMSM for the railway vehicle propulsion system which requires high-speed operation. Therefore, a method to devide the permanent magnet is proposed to reduce the eddy current losses in permanent magnet in this study. Authors analyze the variation characteristics of the eddy current losses generated in permanent magnet of the concentrated winding model by changing the number of the division of the permanent magnets.

• Journal of Advanced Navigation Technology
• /
• v.7 no.1
• /
• pp.59-71
• /
• 2003

The channel scheduler is suggested the radio resource management method in order to provide service with guaranteeing fairness and throughput to the users who use limited wireless channel. Proportional fairness scheduling algorithm is the channel scheduler used in the AMC(Adaptive Modulation and Coding)/TDM system, and this algorithm increases the throughput considering the user's time fairness. In this paper is suggested the channel scheduler combining CDM scheme available in AMC/TDM/CDM system. Unlike the system which only uses TDM which provide the only one user at the same slot, this scheduler can service a lot of users since this uses the CDM scheme with multi-cord channel. At every moment, allocation of transmission power to multi-channel users is problematic because of CDM scheme. In this paper, we propose a water-filling scheduling algorithm to solve the problem. Water-filling fairness(WF2) scheduling algorithm watches the average channel environment. So, this modified method guarantees fairness for each user in terms of power and service time.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.3
• /
• pp.227-247
• /
• 2015

An X-band $8{\times}16$ dual-polarized active phased array antenna system has been implemented based on the substrate integrated waveguide(SIW) technology having low propagation loss, complete EM shielding, and high power handling characteristics. Compared with the microstrip case, 1 dB less is the measured insertion loss(0.65 dB) of the 16-way SIW power distribution network and doubled(3 dB improved) is the measured radiation efficiency(73 %) of the SIW sub-array($1{\times}16$) antenna element. These significant improvements of the power division loss and the radiation efficiency using the SIW, save more than 30 % of the total power consumption, in the active phased array antenna systems, through substantial reduction of the maximum output power(P1 dB) of the high power amplifiers. Using the X-band $8{\times}16$ dual-polarized active phased array antenna system fabricated by the SIW technology, the main radiation beam has been steered by 0, 5, 9, and 18 degrees in the accuracy of 2 degree maximum deviation by simply generating the theoretical control vectors. Performing thermal cycle and vacuum tests, we have found that the SIW array antenna system be eligible for the space environment qualification. We expect that the high efficiency SIW array antenna system be very effective for high performance radar systems, massive MIMO for 5G mobile systems, and various millimeter-wave systems(60 GHz WPAN, 77 GHz automotive radars, high speed digital transmission systems).