• 한국항공우주학회지
• /
• 제31권1호
• /
• pp.97-103
• /
• 2003

연소기 내부에서 연소효율의 증대목적으로 사용되어지고 있는 후향계단후류의 측면제트 분사가 있는 초음속 난류유동장에 대한 수치적 연구를 수행하였다. 본 연구에서는 2차원 Navier_Stokes 방정식과 k-$\varepsilon$ 난류모델식을 고해상도 풍상차분법인 TVD 기법을 사용하여 비정상 유동장에 대한 수치계산을 수행하였다. 유동특성은 제트분사에 의한 마하면이 장애물 역할을 하여 후향계단과 마하면사이에 공동유동(cavity flow)과 비슷한 유동현상이 나타난다. 따라서, 공동 유동에서 발생하는 유동의 진동특성이 나타날 것을 예측할 수 있다. 수치계산 결과에서도 모맨텀플럭스와 분사위치에 따라, 공동유동에서 발생하는 진동특성을 갖는 비정상 유동 특성이 나타나는 것을 볼 수 있었다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제9권1호
• /
• pp.14-17
• /
• 2007

The slot-die coating & calcination process was adopted to fabricate the long YBCO precursor films on the buffered metal tape for the $2^{nd}$ generation coated conductors. To obtain the smooth and crack-free surface of long YBCO precursor films, the parameters of slot-die coating and the process variables of calcination step must be optimized simultaneously in reel-to-reel method. Among the parameter of slot-die coating process, the viscosities of the precursor solution was controlled from 60cP to 200cP to obtain the thicker films from on single coating. The slot-die gap, the injection rate of precursor solution, the moving speed of buffered metal tape etc. are controlled lot the full coverage and smooth surface of YBCO precursor films. The slot-die coated films are moved through the tube furnace with predetermined heating profiles in humid oxygen ambient The YBCO precursor films was identifed with $Y_2O_3,\;BaF_2$, and CuO phase by XRD and consisted of fine grains of about 20nm size observed by FE-SEM. The YBCO films show the critical current density over $MA/cm^2$ using the precursor films formed by the continuous slot-die coating & calcination process.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권1호
• /
• pp.20-26
• /
• 2014

To enhance torque density by harmonic current injection, optimal slot/pole combinations for five-phase permanent magnet synchronous motors (PMSM) with fractional-slot concentrated windings (FSCW) are chosen. The synchronous and the third harmonic winding factors are calculated for a series of slot/pole combinations. Two five-phase PMSM, with general FSCW (GFSCW) and modular stator FSCW (MFSCW), are analyzed and compared in detail, including the stator structures, star of slots diagrams, and MMF harmonic analysis based on the winding function theory. The analytical results are verified by finite element method, the torque characteristics and phase back-EMF are also taken into considerations. Results show that the MFSCW PMSM can produce higher average torque, while characterized by more MMF harmonic contents and larger ripple torque.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2001년도 춘계 학술대회논문집
• /
• pp.15-20
• /
• 2001

Two-dimensional steady flowfields generated by slot injection into supersonic flow are numerically simulated by the integration of Navier-stokes equation with two-equation $\kappa-\epsilon$ turbulence model. High-order upwind scheme is used on unstructured adaptive meshes. The numerical results are compared with experimental data in terms of surface static pressure distributions, the length of the upstream separation region, and the height of the Mach surface for steady flowfields with a Mach number of 3.71 and a unit Reynolds number of $5.83\times10^6/m$.

• 대한조선학회논문집
• /
• 제40권3호
• /
• pp.9-15
• /
• 2003

An experimental study has been carried out as a basic research for development of the friction drag reduction technology for ships by polymer injection. Experimental apparatus and procedures have been devised and prepared to measure the changes of the wall friction with injection of a polymer solution and basic experimental data on the friction drag reduction are obtained for a turbulent fiat-plate boundary layer and fully-developed channel flows. Variations of the friction drag reduction with some important parameters of polymer injection, such as the concentration of polymer solution, its injection flow rate and the measuring position downstream from the injection slot, are also investigated. Important experimental data and results obtained in the present study are presented. The amount of friction drag reduction up to 50% is observed.

• 터널과지하공간
• /
• 제27권5호
• /
• pp.263-270
• /
• 2017

수압암반절개기술은 천공된 시추공에 설치된 이중패커의 인터벌에 암반의 인장응력 이상의 수압을 가하여 균열을 발생시킴으로써 암반을 절개시키는 방법이다. 본 연구에서는 흑운모화강암 사면에 대하여 다양한 배열설계 및 주입설계에 따라 수압암반절개기술을 현장에 적용하였다. 실험 결과, 주입에 따라 새로운 균열이 발생되어 주변 공과 연결되거나 기존 균열이 연장되어 암반이 파괴되었다. 특히, 본 실험에서는 유도 슬롯과 평행한 방향을 지닌 균열이 발생되어 균열 생성방향을 제어할 수 있는 가능성을 제시하였다. 균열생성에 대한 제어 기술을 발전시키기 위해선, 균열생성에 영향을 미치는 여러 요소를 고려한 다양한 배열설계 및 주입설계를 암반 현장에 적용하여야 할 것이다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.553-558
• /
• 2001

To find the effective combinations of blowing ratio and injection angle for a straight slot film cooling, film cooling characteristics was investigated using both flow visualization experiment and numerical simulation. Injection angles from $15^{\circ}\;to\;50^{\circ}$ and blowing ratios from 0.2 to 3.0 were selected for the simulation. Comparison between experimental and numerical results shows a good agreement, for the case of the injection angle of $30^{\circ}$ and blowing ratio ranging from 0.55 to 2.0. Film cooling effectiveness was found to be an increasing function of blowing ratio. The effects of injection angle became prominent as the blowing ratio increases. An interesting phenomenon was found for the injection angle of $15^{\circ}$ : the lowest film cooling effectiveness for the blowing ratio smaller than 1.0, but the highest film cooling effectiveness for the blowing ratio greater than 2.0 within wide range of downstream region. There exist optimum injection angles corresponding to maximum film cooling effectiveness : injection angle of $25^{\circ}$ for the blowing ratio from 0.2 to 2.0, and injection angle of $15^{\circ}$ for the blowing ratio of 3.0. Present study provides a design combination among film cooling effectiveness, blowing ratio, and injection angle.

• 한국추진공학회지
• /
• 제15권3호
• /
• pp.31-39
• /
• 2011

핀/슬롯 그레인 및 내삽노즐을 가진 고체로켓모터 내부와 동일한 기하학적 형상을 가진 표면분사 시험모델을 사용하여 연소유동장을 모사하고, 스모크 와이어를 이용하여 유동장을 가시화하였다. 그레인 전방부 투영창을 통해 촬영하는 기법 등에 이용하여 획득된 내삽노즐 선단 인접부의 반경방향 평면상에서의 유동가시화 이미지 분석을 통해, 슬롯출구 반경방향유동, 핀베이스 축방향유동 및 상류그레인포트 축방향유동의 상호 전단작용에 의한 반경방향 운동량 전달이 노즐 인접부에서의 선회류 유동 및 와류튜브 구조를 발생시키는 것으로 나타났다.

• 한국정밀공학회지
• /
• 제31권3호
• /
• pp.215-222
• /
• 2014

This paper presents an experimental study of a vibration-assisted dry micro-wire electrical discharge machining (${\mu}$-WEDM) utilized in high precision and micro-manufacturing area. The assisted vibration was applied to the workpiece using a piezoelectric actuator, and high pressure air was injected directly into the machining gap through a nozzle. Investigation experiments were performed to estimate the importance of input parameters and it was observed from experiment results that the width (kerf) of the cutting slot and the machining time were significantly affected by the air injection pressure and input energy. Moreover, it was also observed that there exists an optimal relationship between the machining time and input parameters including the air pressure and vibration frequency and amplitude. Central composite design based experiments were also carried out, and empirical models of the machining time and cutting slot kerf have been developed using the response surface methodology to analyze and optimize the process.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.3529-3533
• /
• 2007

The advantages of the SITVC(secondary injection thrust vector control) technique over mechanical thrust vector systems include a reduction in both the nozzle weight and complexity due to the elimination of the mechanical actuators that are used in conventional vectoring. Computational study is performed to understand the fluidic thrust vectoring control of an axisymmetric nozzle, in which secondary gas injection is made in the divergent section of the nozzle. The nozzle has a design mach number 3. The effect of injection hole number and shape of secondary jet on the mach number distribution of SITVC were investigated. The standard ${\kappa}$ - ${\epsilon}$ turbulence model solved the complex three-dimensional nozzle flows perturbed by the secondary gas jet. The numerical code was validated by experiment. The results showed that the mach number distribution of circular and square nozzle are similar each other. As number of second injection hole increasing, a effect of deflection was decreased.