• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.599-606
• /
• 2010

It has been reported that many slope failures in unsaturated soils are mainly caused by downward infiltration due to rainfall. The rainfall characteristics could be an important factor, and more predictable slope failures can be achieved by considering more reasonable rainfall conditions. So, a need exists that these trends of infiltration in weathered soils, which is commonly found in Korea, are assessed by considering rainfall conditions based on phenomenological approach. In this paper, numerical analyses of unsaturated soil slope under rainfall conditions are presented based on the soil-water characteristic curve in the laboratory and huff method. Then the performance of unsaturated weathered soil slopes was evaluated under various conditions after applying the effect of overburden pressure on SWCCs and fines contents. The results demonstrated that the rainfall conditions using Huff method can be very effective and the proper application on analysis is very important to enhance the prediction on unsaturated slope stability.

• Journal of Industrial Technology
• /
• v.21 no.A
• /
• pp.33-40
• /
• 2001

Heat loss from the trapezoidal fins haying different upper side slope and that from a rectangular fin are investigated by the three dimensional analytic method. It is shown that the trapezoidal fins having different upper side slope become an approximate rectangular fin by inst adjusting the slope factor. The comparison of the heat loss between a rectangular fin and an approximate rectangular fin is represented as a function of the non-dimensional fin length, fin width and Biot number to make sure that the analysis on the trapezoidal fins having different upper side slope is countable. One of the results is that the relative value of heat loss between a rectangular fin and an approximate rectangular fin is less than 1.5% for given ranges of non-dimensional length and width in case of Bi = 0.1.

• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.60-64
• /
• 2010

The purpose of this study if to prevent dangerous accident of the overthrow of the tower crane in summer's hurricane. We develop the SMS in order to give automatic alarm system to operator within the dangerous range and to give a information of the exactly slope in the real time. The slope value of the tower crane is compose of direction, pitch by the front and rear, roll by the right and left and synthesis by the its pitch and roll. Especially, the synthesis eliminate the effect of the wall tie or wire bracing. So, this value should correctly indicate the actual slope. In this study, more applying field test should be applied with the SMS. In the future, a more measurement device can be applied to, and be able to feed more alarm criteria for the review of the risk in the field.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1963-1968
• /
• 2004

A collection efficiency of cyclone is influenced by cut-size and slope of grade efficiency curve. It has been recognized that the collection efficiency is improved when the cut-size is reduced. However, effects of the slope have never been studied so far. In this study, we analyze a relationship between slope of grade efficiency and collection efficiency in two-stage cyclones. In single stage cyclones, higher slope cyclones have high efficiency. On the contrary to single stage cyclone, collection efficiency of two-stage cyclone have the maximum value when the first cyclone has a lower slope and second cyclone is high.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.4 s.59
• /
• pp.40-45
• /
• 2004

An efficient numerical model of the modified mild slope equation, based on the robust iterative method is presented. The model developed is verified against other numerical experimental results, related to wave reflection from an arc-shaped bar and wave transformation over a circular shoal. The results show that the modified mild slope equation model is capable of producing accurate results for wave propagation in a region where water depth varies substantially, while the conventional mild slope equation model yeilds large errors, as the mild slope assumption is violated.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.515-523
• /
• 2020

If the safety factor does not secure the safety factor suggested in the design standard at the slope design stage, the safety factor is secured by installing an anchor. Stability analysis is used to verify the effect of reinforcing the slope of the anchor, but in this process, most of the anchor construction intervals are assumed to be equal and analyzed. For economical and effective slope reinforcement, stability analysis is required by adjusting the anchor construction interval. In this study, the effect of the anchor construction interval on the change of the safety factor of the slope was identified. Stability analysis was performed by setting a virtual slope with two berms and different anchor construction intervals. As a result of the analysis, the stability of the slope is secured when the anchor spacing of the lower surface is narrowed and the anchor gaps of the upper and middle surfaces are wider than when anchors are installed at the same intervals on the upper, middle, and lower surfaces of the slope. The result was a 15% reduction in the amount of anchors. This means that, rather than reinforcing anchors at the same intervals, it is economical and effective to have an economical and effective reinforcement effect to vary the anchor construction intervals according to the slope characteristics.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.5
• /
• pp.21-28
• /
• 2023

In this paper, an experimental study was conducted to present the properties of rapid hardening composite mat, and a numerical analysis was carried out to analyze the slope protection effect of the mats based on ground conditions, rainfall, slope gradient and soil height. As a result, the application of rapid hardening composite mat increased the slope safety factor in all conditions, and the increase rate of safety factor showed an average of 40% increase both in dry and rainy seasons. Through these research findings, the protective effect of the rapid hardening composite mat on sloping surfaces has been proven, and it is suggested that the rapid hardening composite mat is suitable for application in areas where slope failure or collapse is expected.

• Journal of the Korean Society of Safety
• /
• v.30 no.2
• /
• pp.48-55
• /
• 2015

The number of collapse accidents relevant to form support since 2003 is 30 on the basis of statistical data from Ministry of Employment and Labor,. Total number of casualty was 138 (47 for deaths and 91 for injuries). The accident severity rate was high because the 4.6 casualties per one accident were occurred averagely although the incident rate was relatively low. Especially, one of form support members, the pipe supports have not been equipped adequately so that the accidents could have happened. In this regard, this study performed buckling test related to the effect of horizontal connection and slope in the single pipe which is one of typical pipe supports. The buckling load, which was estimated from the single pipe with the horizontal connectors theoretically and experimentally, was increased as more than 2 times compared to the buckling load obtained from the pipe supports without the connector. The buckling load was reduced as more than 26%, 34% slope of the single pipe comparing with 5% and 10% slope, respectively. Thus, the purpose of this study is to provide the guideline for installation and the maintenance of the pipe supports legally and institutionally to prevent the collapse accidents of the pipe supports.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.24 no.2
• /
• pp.1-12
• /
• 1996

In order to develope a road landscape that is in harmony with landscaping purpose, degree of sight occupation by slopes at road sides was measured and physical elements composing the slope scenery were visually evaluated and the results are as follows : In analysis of sight occupation ratio by perspective method, gradient of the slopes influenced more on the sight occupation than height did and the driving lane occupied 2 to 3% more proportion of sight than the passing lane. When there is slope at one side of the road, difference in sight occupation between the lanes was increasing with deceased height and with increased gradient of the slopes. In visual analysis of the slope scenery, negative image was increasing with narrow road, increased height and gradient of the slopes. In visual analysis of the slope scenery, negative image was increasing with narrow road, increased height and gradient of the slopes. Particularly, the effect of gradient was critical on scenery. The effect of the slopes was negative at 60$^{\circ}$ or more but positive at 45$^{\circ}$or less gradient. This phenomenon was more conspicuous with wide 4 lane roads than wide 2 lane roads. Although direct comparison is difficult due to a great difference between Korea and U.S.A. in climate, land condition, road dimension, and public process of purchasing land, etc, it is desirable to treat road sides so that the scenery is in harmony with landscape around as well as emphasizing the regional characteristics, also giving friendly and comfortable image to drivers and nearby residents in addition to safety as can be seen in U.S.A.

• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.14-19
• /
• 2005

In high speed $CO_2$ welding, it has been blown to produce no sound bead with undercut or humping bead. In this study welding phenomena through synchronized high speed camera and output welding voltage and current waveform has been analyzed. For the purpose to improve a welding bead, effect of short circuit current rise slope has been examined. With commercial power source it was produced no sound bead by instantaneous short circuit, long arc period and stubbing at welding speed 2.5mm/min Humping bead or undercut were showed by instantaneous short circuit and long arc period. Also, the weld bead was not formed during the long short circuit period after stubbing start and long arc extinguishment period after wire sticking by failure of arc regeneration, because the droplet was not transferred to weld pool. With increasing short circuit current rise slope the frequency of stubbing was decreased and the normal short circuit rate was increased. A control of short circuit current rise slope was effective factor in high speed welding.