• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.3
• /
• pp.207-214
• /
• 2019

In this study, discrete-time domain analysis is proposed to investigate the input current of a buck AC/DC light-emitting diode (LED) driver. The buck power factor correction converter can operate in both discontinuous conduction mode (DCM) and continuous conduction mode (CCM). Two discontinuous and two continuous conduction operating modes are possible depending on which event terminates the conduction of the main switch in a switching cycle. All four operating modes are considered in the discrete-time domain analysis. The peak current-mode control with slope compensation is used to design a low-cost AC/DC LED driver. A slope compensation design of the buck AC/DC LED driver is described on the basis of a discrete-time domain analysis. Experimental results are presented to confirm the usefulness of the proposed analysis.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.33-39
• /
• 2021

This paper presents an optimized design technique that can satisfy the design input values. Numerical analysis was performed on the slope correction device based on the first design. The stress distribution was confirmed when the load specified as the design input value was applied, and design changes were introduced for parts for which the design safety factor did not meet the standard to ensure rigidity. And the results were verified through FEA.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.27-43
• /
• 2002

This paper described two case studies on large scale failure of cutting slope. The kind of rock in both sites predominated limestone and shale respectively. These cutting slopes located in northern area of Gyongbug Province are composed of very complicated and various rock mass. Geological characteristics, causes of failure, proceeding of security diagnose, maintenance method etc. of two sites were carried out to check the cutting slope stability and to provide reasonable maintenance method. This paper may provide the useful data for engineers related with design and construction of large cutting slope.

• Journal of the Korean Geotechnical Society
• /
• v.26 no.11
• /
• pp.75-87
• /
• 2010

Incessant rainfalls in unsaturated soil raises pore water pressure and drops shear stress. Controlling pore water pressure in unsaturated soil prevents pressure increase and leads to slope stability. Laboratory experiment of pore water absorption in soil tank has been conducted for pore pressure decrease in soil slope under artifical rainfall supplied in varying rainfall indensities. Soil slope failure triggers the deepening of the wetting front to critical depth accompanied by decrease in matric suction induced by water infilteration. This paper addresses an experimental design for absorption pipe to prevent pore pressure increase in unsaturated soil slope from heavy rain. It is expected that absorption pipe will be widely used in unsaturated soil slope to strengthen slope stability.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.9 no.1
• /
• pp.100-111
• /
• 2006

This study was carried out to increase the efficiency of site investigation through the evaluation of the applicable methods of investigation for cutting slope design. In an effort to find out the applicability of the method employed during the slope investigation, some tests were carried out on 6 subjects i.e location of weak zones, characteristics of discontinuities, distribution of strata, in situ tests for geo-technical properties, laboratory test and estimation of weathering. The method was highly applicable and produced expected results during the test of weak zones, discontinuities and distribution of strata. In order to apply the method to in- situ test for geo-technical properties and laboratory test on soil and rock slope, a statistic analysis of the existing data were required in advance. However its design applicability on rock slope was good although actual cases of application were not many due to limitation of the cases for investigation. The method was frequently referenced but not actually applied for anti seismic design test and estimation of weathering.

• Geomechanics and Engineering
• /
• v.24 no.4
• /
• pp.389-397
• /
• 2021

Pile foundation is a typical form of bridge foundation and viaduct, and large-diameter rock-socketed piles are typically adopted in bridges with long span or high piers. To investigate the effect of a mountain slope with a deep overburden layer on the bearing characteristics of large-diameter rock-socketed piles, four centrifuge model tests of single piles on different slopes (0°, 15°, 30° and 45°) were carried out to investigate the effect of slope on the bearing characteristics of piles. In addition, three pile group tests with different slope (0°, 30° and 45°) were also performed to explore the effect of slope on the bearing characteristics of the pile group. The results of the single pile tests indicate that the slope with a deep overburden layer not only accelerates the drag force of the pile with the increasing slope, but also causes the bending moment to move down owing to the increase in the unsymmetrical pressure around the pile. As the slope increases from 0° to 45°, the drag force of the pile is significantly enlarged and the axial force of the pile reduces to beyond 12%. The position of the maximum bending moment of the pile shifts downward, while the magnitude becomes larger. Meanwhile, the slope results in the reduction in the shaft resistance of the pile, and the maximum value at the front side of the pile is 3.98% less than at its rear side at a 45° slope. The load-sharing ratio of the tip resistance of the pile is increased from 5.49% to 12.02%. The results of the pile group tests show that the increase in the slope enhances the uneven distribution of the pile top reaction and yields a larger bending moment and different settlements on the pile cap, which might cause safety issues to bridge structures.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.10a
• /
• pp.16-26
• /
• 2002

As the slope designs had simply followed some slope guidelines during 1960's∼1970's, of which the main purpose was to estimate earth work quantities in the feasibility stage, slope failures had been experienced in Korea Highways. Various site investigation methods for highway cut-slopes have been continuously developed, and major cut-slope failures caused by slope instability have rapidly reduced. The failure mode of recent cut-slope failures in highways during typhoon RUSA No.15. featured a debris flow in soil mass activated by flowing water. The study of the surface soil scour and the debris flow caused by heavy rainfall must be done to protect the cut-slope failures in the future

• Geotechnical Engineering
• /
• v.10 no.4
• /
• pp.133-152
• /
• 1994

In the present study, an economic design of Anchored Geosynthetic(AG) System applied mainly to reinforce unstable soil slopes is investigated. For this purpose methods of stability analysis are developed to determine the optimum installation angle, required minimum length and maximum spacing of nails. Anchorage of nails within the soil mass is achieved by frictional resistance to pull out along the effective length of the nails. Cases of infinite slope and finite slope are dealt with individually. Silce methods of stability analysis developed in the present study are limit-equilibrium-based. For the case of finite slope Spencer method which considers interslice force is modified to evalyate the overall stability. In addition, the effects of various design parameters on requried length and spacing of nails corresponding to the optimum orientation of nails are analyzed. Based on the analysis, a simplified equation is given for the optimum nail orientation. Also the importance of optimum nail orientation is illustrated throughout design example, and the appropriateness of judgment criterion are examined.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.5
• /
• pp.13-21
• /
• 2019

There are many cuts or natural rock slopes that remain stable for a long time in the natural environment with steep slopes ($65^{\circ}$ to $85^{\circ}$). In terms of design practice, the rock mass consisting of similar rock condition and geological structures is defined as a good continuum rock slope, and during the process of decision making angle of this rock slope, it will be important to establish the geotechnical properties estimating method of the continuum rock on the process of stability analysis in the early stages of design and construction. In this study, the stability analysis of a good continuum rock slope that can be designed as a steep slope proposed a practical method of estimating the shear strength by induced from the Hoek-Brown failure criterion, and in addition, the design applicability was evaluated through the stability analysis of steep rock slope. The existing method of estimating the shear strength was inadequate for practical use in the design, as the equivalent M-C shear strength corresponding to the H-B envelope changes sensitively, even with small variations in confining stress. To compensate for this problem, it was proposed to estimate equivalent M-C shear strength by iso-angle division method. To verify the design applicability of the iso-angle division method, the results of the safety factor and the displacement according to the change in angle of the cut slope constructed at the existing working design site were reviewed. The safety factor is FS=16~59 on the 1:0.5 slope, FS=12~52 on the 1:0.3 slope, most of which show a 10~12 percent reduction. Displacement is 0.126 to 0.975 mm on the 1:0.5 slope, 0.152 to 1.158 mm on the 1:0.3 slope, and represents an increase of 10 to 15%. This is a slightly change in normal proportion and is in good condition in terms of stability. In terms practical the working design, it was confirmed that applying the shear strength estimated by Iso-angle division method derived from the H-B failure criterion as a universal shear strength for a good continuum rock mass slope was also able to produce stable and economic results. The procedure for stability analysis using LEM (Limit Equilibrium Analysis Method) and FEM (Finite Element Analysis Method) will also be practical in the rock slope where is not distributed fault. The study was conducted by selecting the slope of study area as a good rock condition, establishing a verification for which it can be applied universal to a various rock conditions will be a research subject later on.

• Journal of the Korean Statistical Society
• /
• v.35 no.2
• /
• pp.179-192
• /
• 2006

In this paper, a new method of modified second order slope rotatable designs (SOSRD) using balanced incomplete block designs (BIBD) for $4{\le}v{\le}16$ is presented. In this method the number of design points required is in some cases less than the number required in Victorbabu (2305) modified slope rotatable central composite designs. Further, a new method of construction of three level modified SOSRD using BIBD is presented. The modified SOSRD can be viewed as SOSRD constructed with the technique of augmentation of second order rotatable design (SORD) using BIBD to SOSRD. These designs are useful in parts to estimate responses and slopes with spherical variance functions.