• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• 한국자동차공학회논문집
• /
• 제21권1호
• /
• pp.121-127
• /
• 2013

In this study, suspension geometry is controlled to improve vehicle handling performance. The toe and camber of the rear suspension is controlled independently by using a double knuckle structure designed to enhance the vehicle cornering stability. Camber and toe changes in the rear wheel during high speed turning maneuver are important factors that influence the vehicle stability. Toe in the rear outer wheel plays a dominant role in cornering. A control algorithm for the camber and the toe angle input is developed to carry out the control simulation of the vehicle such as single lane change, the steady state cornering, the double lane change and the step steering simulation. Effects of the camber and toe angle control are analyzed from the computer simulations. A double lane change simulation revealed that the suspension mechanism with variable camber angle and variable toe angle decreases the peak body slip angle and peak yaw rate, 50% and 10%, respectively.

• 대한조선학회논문집
• /
• 제48권6호
• /
• pp.516-527
• /
• 2011

This paper considers a numerical analysis of ship maneuvering performance in the high amplitude incident waves by adopting linear and nonlinear ship motion analysis. A time-domain ship motion program is developed to solve the wave-body interaction problem with the ship slip speed and rotation, and it is coupled with a modular type 4-DOF maneuvering problem. Nonlinear Froude-Krylov and restoring forces are included to consider weakly nonlinear ship motion. The developed method is applied to observe the nonlinear ship motion and planar trajectories in maneuvering test in the presence of incident waves. The comparisons are made for S-175 containership with existing experimental data. The nonlinear computation results show a fair agreement of overall tendency in maneuvering performance. In addition, maneuvering performances with respect to wave slope is predicted and reasonable results are observed.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.55-63
• /
• 2001

Friction and wear properties of brake friction materials containing different metal fibers (Al, Cu or Steel fibers) were investigated using a pad-on-disk type friction tester. Two different materials(gray iron and Al-MMC)) were used for disks rubbing against the friction materials. Results from ambient temperature tests revealed that the friction material containing Cu fibers sliding against cast iron disk showed a distinct negative ${\mu}$-ν (friction coefficient vs. sliding velocity) relation implying possible stick-slip generation at low speed. The negative ${\mu}$-ν relation was not observed when the Cu-containing friction materials were rubbed against the. Al-MMC counter surface. As applied loads increased, friction materials showed higher friction coefficients comparatively. Friction materials slid against cast iron disks exhibited higher friction coefficients than Al-MMC disks during high temperature tests. On the other hand, high temperature test results suggested that copper fibers in the friction material improved fade resistance and the steel fibers were not compatible with Al-MMC disks showing severe material transfer and erratic friction behavior during sliding at elevated temperatures.

• 한국소음진동공학회논문집
• /
• 제23권7호
• /
• pp.624-630
• /
• 2013

In this study, a parametric study is performed to investigate the squeal noise of an automobile water pump. The squeal noise studied in this paper is generated by the self-excited torsional resonance of the rotating shaft, and this noise is related to the stick-slip phenomenon of the mechanical seal in the water pump. The mechanical seal friction has the characteristics of the negative velocity-gradient. The equations of motion of multiple-degree-of-freedom torsional vibration model is constructed by the Holzer's method and then the equation is transformed to an equivalent single-degree-of-freedom torsional resonance simulation model. A squeal noise criteria is determined by the simulation model to perform the parametric study. The design parameters(the mass moment of inertia of the pulley, the mass moment of inertia of the impeller, the length of the shafts, the radius of the shafts, spinning speed of the shafts, the position of the mechanical seal, radius of the mechanical seal, and normal load of the mechanical seal) are investigated to confirm the stability for the squeal noise.

• 한국기계가공학회지
• /
• 제21권3호
• /
• pp.29-35
• /
• 2022

When a vehicle is driven off a road surface, the deformations of the road surface and tire are combined. Consequently, the dynamic behavior of wheel movement becomes difficult to predict and control. Herein, we propose a tire test bed to capture the dynamic behavior of tires moving on sand and soil. Based on this study, it is discovered that the slip rate can be controlled, and the vertical force can be measured using a load cell. The test results show that this test bed can be useful for capturing the dynamic behavior of the tire and validating dynamic simulations. In fact, the tire test bed developed in this study can be used to verify the results of computer simulations. In addition, it can be used for basic experiments pertaining to the speed control of unmanned autonomous vehicles.

• Tribology and Lubricants
• /
• 제39권4호
• /
• pp.123-132
• /
• 2023

In this study, the expansion, stress, and operating clearance of bearing elements during operation are observed using the inner/outer ring temperature test data of a 3.0×10⁶ DN-class roller bearing. The operating clearance characteristics of inner-/outer-ring cooling (IORC) bearings are compared to those of inner-ring cooling (IRC) bearings. For IRC bearings, the thermal expansion of the outer ring is the most important factor in clearance variation. As a result, the operating clearance is less than the initial clearance of 61 ㎛, and the operating clearance decreases to 0.5 ㎛ at 25,500 rpm. Conversely, the temperature of the outer ring of IORC bearings is lower than that of IRC bearings, so the operating clearance is kept smaller. When the coolant flow rate to the outer ring is approximately 1.5 to 2.0 L/min, the temperature difference between the inner and outer rings is minimized and the operating clearance is maintained at a significantly lower level than IRC bearings. Small operating clearances are expected to be effective in reducing cage slip and skid damage in roller bearings. The results and analysis procedures of this study can be utilized to design of bearing clearance, lubricant flow rate, and assembled interference in the early design stage of aerospace roller bearings.

• 한국산학기술학회논문지
• /
• 제18권3호
• /
• pp.609-614
• /
• 2017

본 연구에서는 부피는 기존 1단 감속기와 동일한 수준을 유지하면서 2단의 감속비를 갖는 소형감속기에 대한 개발을 위하여 새로운 형태의 편심캠을 이용한 감속기의 연구를 진행하였다. 따라서 자동차에 적용되는 무단변속기의 개념을 이용하여 2단 감속기를 설계하였다. 캠은 감속풀리와 가속풀리에 각각 연결되어있는 V-벨트를 압착하여 미끄러짐을 최소화하기 위하여 텐셔너 역할을 할 수 있도록 $180^{\circ}$의 위상차를 두고 편심형태를 가지는 구조로 설계하였다. 또한 캠의 직경을 35mm로 하고, 외경의 폭을 18mm로 하여 v-벨트의 외측부분과 캠이 완벽하게 접촉할 수 있는 구조로 설계하였다. 감속을 위한 저속 풀리는 입력축에 지름 50.8mm의 풀리를 설치하고, 출력축에 지름76.2mm의 풀리를 설치하였다. 가속을 위한 고속 풀리에는 입력축에 지름 76.2mm의 풀리를 설치하고, 출력축에 지름 50.8mm의 풀리를 설치하였다. 설계된 내용을 토대로 변속기의 동력전달효율실험과 발열특성에 대한 실험을 진행하여 타당성을 검증하였다. 또한 타당성 검증을 통하여 감속기의 적합성을 증명하였다.

• 한국철도학회논문집
• /
• 제16권1호
• /
• pp.7-13
• /
• 2013

철도차량의 실차 규모 동특성시험은 설비 구축, 대차의 제작 및 시험 조건의 설정등과 관련하여 비용, 시간 등의 증대로 많은 어려움이 따른다. 본 연구에서는 실험실 환경에서 차량 진동문제와 안전성을 평가하기 위한 목적으로 축소모델을 제작하고, 개발된 축소모델이 해당 철도차량의 동특성을 정밀하게 모사하는지를 검증하는 평가방법에 대한 연구를 수행하였다. 축소이론은 Jaschinski 상사기법의 이론을 적용하였으며, 1/10 축소모델을 구축하였다. 본 연구에서는 축소 대차의 상하 진동에 초점을 맞혀 시스템을 제작하였다. 시스템은 구동부, 보기, 대차 등 3개의 하부구조로 구성되었으며, 실제 차량으로 환산 시 400km/hr까지 실험가능 하도록 목표로 하였다. 축소 대차의 설계 및 제작과 함께, 동역학해석 프로그램인 ADAMS/View를 이용하여 고유치 해석을 수행하였다. 전산해석으로 도출된 고유진동수는 실험결과와 비교 분석되었다. 시스템이 가지고 있는 초기 5개의 자유도에 상응한 고유진동수를 비교한 결과, 개발된 상사 이론에 따른 축소모형은 충분한 신뢰성을 확보한 것으로 검증되었다. 본 연구에서 개발된 축소모델은 대학실험실에서 차량진동모드를 모사하는 용도로 기획되었으나, 추후 자유도의 추가보완을 통해 고속철도 차량의 대차와 보기구조 동특성 해석에 활용될 수 있을 것으로 판단된다.

• 한국지반공학회논문집
• /
• 제29권5호
• /
• pp.39-52
• /
• 2013

본 연구는 포화-압밀-전단 제어형 링전단시험장치를 이용하여 (i) 전단시간에 따른 전단응력 특성, (ii) 구속압과 전단속도에 따른 전단특성 및 (iii) 전단속도에 따른 전단응력 특성에 대한 연구를 수행하였다. 이질 재료간의 전단특성을 살펴보고자 낙동강 모래와 해안 점토를 사용하였다. 본 연구에서는 모래와 모래, 점토와 점토, 모래와 점토끼리의 전단특성을 살펴보고자 비배수 조건에서 특정 구속압(50과 100kPa)에 대한 실험을 1차적으로 수행하였다. 모든 실험은 특정 구속압에 대해 300sec 동안 자동 압밀조건을 거친 후 전단실험을 수행하였다. 2차 실험으로 세 시료에 대한 수직응력 변화에 따른 전단응력 특성을 살펴보고자 수직응력을 20~150kPa까지 단계별로 높여가며 실험을 수행하였다. 마지막으로 특정 구속압에 대해 전단속도를 0.01, 0.1, 1, 10, 100mm/sec까지 5 단계로 나누어 실험을 수행하였다. 이질재료 간의 전단응력은 특정 구속압 하에서 모래-점토의 전단응력(최대전단응력과 잔류전단응력)은 모래-모래보다는 작고, 점토-점토보다는 약간 큰 것으로 나타났다. 전단응력은 구속압과 전단속도에 의해 전단면에서 발생하는 입자 파쇄와 젖음현상에 의존하는 것으로 나타났다.