• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.420-424
• /
• 1997

n the ballscrew slide system the ~najor problems in accomplishing the high-speed and high-precision are the friction between elements and the decrease of axial stiffness. Especially the friction on the guide have a bad effect on the precision of slidlng. Furthermore stick-slip occur when the low stiffness of slide system. The sticli-slip have a bad influence on the precision. In this research, the affection of stick-slip friction to the precision of the slide system is studied and the possible solution of the precision is proixjsed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.74-80
• /
• 2009

The objective of this paper was to investigate the slip rate and the slip frequency number of damper clutch of torque converter in 2.4L passenger vehicle with 5-speed A/T and analyze the effect of slip control and control strategy on driving characteristics and the fuel economy. The newly developed torque converter with the more durable wet friction material and the slip-controlled damper clutch system, the DCC system, was installed, which was easily compatible and amendable of the lock-up clutch of the base system. The vehicle has been tested on the fuel economy modes such as FTP-75, HWFET and NEDC (ECE15+EUDC) driving cycle at chassis dynamometer. The DCC mode (II), of which the control strategy had both the lock-up and the slip-controlled clutch, and the DCC mode (I) with full slip-controlled clutch were compared with the base system with only the lock-up clutch. As the research result, comparison to base system, the fuel consumption of the vehicle with the DCC control (II) was effectively improved by 6.6% and 7.7% on FTP-75 and NEDC mode.

• 전기의세계
• /
• v.31 no.4
• /
• pp.303-307
• /
• 1982

This paper describes how to improve a induction moter efficiency by a slip frequency control. Digital filter controlled by microcomputer is introduced in control system of a constant speed-drive and it has prove that the moter can be drived with a high efficiency at a constant slip frequency. The constant slip frequency control method has a merit of simplness.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.6
• /
• pp.226-233
• /
• 1998

In this paper, an experimental study was performed to investigate the speed ratio-torque-thrust characteristics for metal belt CVT. It is observed from the experimental results that nondimensional secondary thrust force follows with the existing theoretical formula with ${\mu}$=0.09~0.12 depending on the torque and the speed ratio. In order to represent these characteristics, an effective friction coefficient was introduced. Also, the slip characteristics between the belt and the pulley were investigated experimentally and traction coefficients at gross slip were obtained for various speed ratios. Using the traction coefficients and the effective friction coefficients, an improved formula for the secondary thrust force was suggested assuming that thrust force is the summation of the thrust of pseudo inactive arc and the thrust of pseudo active arc. The effective friction coefficient and the improved formula for the speed ratio-torque-thrust relationship suggested in this work can be used to obtain the appropriate secondary thrust.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.212-212
• /
• 2000

This study was performed to construct a hot strip speed measuring system and check over whether the measured speed can be used for improving the mass flow of the head-end part of a hot strip in the 7-stand finishing mill. Because the mass flow in hot rolling mill affects the looper operation and the thickness and width control of a strip, accurate measurement of strip speed ie important. The measured speed was compared with the roll speeds of No. 6 and No.7 stand to check the performance of the system and analyzed to find how to apply the speed. As a result, it is shown that the accuracy of the system is enough, strip thickness error can be reduced by -275∼+200$\mu\textrm{m}$ using the measured speed and the existing FSU model has low accuracy for predicting forward slip rate. A neural network was developed to calculate forward slip rate instead of FSU model. The test result of the neural network shows that the neural network is more accurate than the FSU model.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.334-340
• /
• 2002

This paper proposes a new anti-slip re-adhesion control system fur electric railway vehicle driven by inverter-fed induction motors. This paper introduces an instantaneous tangential farce coefficient estimator between driving wheel and rail, which is based on disturbance observer. The torque command of proposed system regulates to exceed this estimated tangential farce coefficient in order to avoid undesirable slip phenomenon of driving wheels. We have already proposed the anti-slip re-adhesion control system based on disturbance observer for simplified one wheel equivalent model successfully. This paper extend to this system to the actual bogie system, which has four driving wheels driven by two induction motors fed by one inverter. In order to apply anti-slip re-adhesion control to the actual bogie system a new anti-slip re-adhesion control based on both disturbance observer and speed sensor-less vector control of induction motor with quick response are combined. The experimental results and the numerical simulation results prove the validity of the proposed control system.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.509-514
• /
• 2004

This paper introduces the modified slip energy recovery system in order to improve its power factor and to reduce harmonics of line current waveforms. Twelve pulse line commutated converter with the chopper type IGBT is applied where the chopper is applied across the DC terminal and the chopped DC is fed to the converter operating as an inverter and then passed through the wye-wye and delta-wye transformer circuit. This scheme leads to be able to adjust the speed of the motor by the duty cycle of the chopper operating in PWM mode. The fuzzy logic controller is also introduced to the modified slip energy recovery system for keeping the motor speed to be constant when the load varies. The experimental results in testing the 0.22 kW wound rotor induction motor from no-load condition to rated condition show the effectiveness of the proposed control scheme.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.641-644
• /
• 1991

Constant slip frequency operation of linear infliction motor is essential for the stable levitation. Control scheme for the constant slip frequency with general purpose frequency inverter is proposed, Speed sensing scheme with proximitity switch for the speed feedback is also proposed. Optimal slip frequency, at which normal force is equal to 0, is selected by the experiment. This slip frequency is a comand to the controller. It shows good characteristic during acceleration and deceleration.

• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.347-349
• /
• 1998

This paper describes a fuzzy identification model for slip - adhesion curve of High - speed trains. The model has fuzzy inputs corresponding to rail condition and crisp inputs for train. Nonlinear function is obtained by using fuzzy outputs. Finally slip - adhesion curve is given by the function. First, Results are presented of slip - adhesion curves under the influence of changing rail condition. Second, Dynamic moving simulation by proposed fuzzy slip - adhesion model is presented. Simulation results show fine characteristics.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.10
• /
• pp.2299-2304
• /
• 2010

A sensorless vector control of an induction motor provides a good performance in the middle and high speed region. However, in the low speed region, it is very difficult to implement the sensorless vector controller because the feeding voltage measured by the motor is very low. In this paper, we designed the sensorless vector controller of an induction motor using the estimate of the slip frequency. To verify the performance of the proposed controller, an experiment has been performed.