• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.32 no.3
• /
• pp.180-201
• /
• 2020

It has been widely known that the effect of diffracted waves at the tip of composite breakwater with finite length causes the change of standing wave height along the length of breakwater, the spatial change of wave pressure on caisson, and the occurrence of meandering damage on the different sliding distance in sequence. It is hard to deal with the spatial change of wave force on trunk of breakwater through the two-dimensional experiment and/or numerical analysis. In this study, two and three-dimensional numerical techniques with olaFlow model are used to approach the spatial change of wave force including the impulsive breaking wave pressure applied to trunk of breakwater, the effect of rear region, and the occurrence of diffracted waves at the tip of caisson located on the high crested rubble mound. In addition, it is thoroughly studied the mean wave height, mean horizontal velocity, and mean turbulent kinetic energy through the numerical analysis. In conclusion, it is confirmed that the larger wave pressure occurs at the front wall of caisson around the still water level than the original design conditions when it generates the shock-crushing wave pressure checked by not two-dimensional analysis, but three-dimensional analysis through the change of wave pressure applied to the caisson along the length of breakwater.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2010.03a
• /
• pp.379-389
• /
• 2010

It is very important to determine a target probability of failure in reliability based design such as an allowable factor of safety in working stress design because they are indices to judge the stability of structures. We have carried out reliability analyses of nationwide gravity type quay walls and found that sliding and foundation failures of quay walls were dominant failure modes for every case of loads. And a target probability of failure for bearing capacity of foundation of quay wall was also determined in this study. Of several approaches which have been suggested until now, a couple of reasonable approaches were used. Firstly, in order to consider the safety margin of structures which have been executed so far, the reliability levels of existing structures were assessed. And then a mean probability of failure for the quay walls was estimated. In addition, life cycle cost(LCC) analyses for representative structures were performed. Probabilities of failure for several quay walls were calculated with changing the width of each quay wall section. LCC of quay wall which is requiring case by case during the service life was evaluated, and also the optimum probability of failure of quay wall which minimizes LCC was found. Finally, reasonable target probabilities of failure were suggested by comparing with mean probability of failure of existing structures.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.9 no.1
• /
• pp.161-171
• /
• 2007

The purpose of this study was to classify the lower body of the lost women and to investigate the three-dimensional characteristics of each lower body somatotype of them. The subject were ninety seven women whose. age were twenties and whose height and bust girth were in the range of mean$\pm1\delta$ of typical body size of twenties' Korean women. The forty one variables of their lower body were measured by Martin's Anthropometric Instrument. And they were analyzed for mean, standard deviations factor analysis, and cluster analysis. In the second phase of analysis, the three participants were re-selected in each type were measured by Sliding Guage and analyzed their lower body somatotype. The results were as follows; The components of lower body of 20s' women were extracted with 7 factors through factor analysis and orthogonal rotation by the method of Varimax. The rate of the cumulative contribution was 84.1% the first factor was the thickness of lower body, the second factor was the vertical size of lower body the third factor was the front shape of hip, the forth factor was the vertical size of hip, the fifth factor was the shape of abdomen, the six factor was the flat-ratio of waist and the seventh factor was flat-ratio of hip. The somatotype of 20's women's lower body can be classified into 3 types. Type 1 is the standard somatotype of 20's women's lower body and the 34.0% of the participants in the study was categorized into type 1. Type 2 is a short and corpulency type with protruded abdomen and hip and the 29.9% of the participants in the study was categorized into type 2. And the type 3 is a tall and thin type with plat abdomen and hip and the 37.1% of the participants was categorized into type 3.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.2
• /
• pp.380-385
• /
• 2006

In this paper, a program that can be utilized to measure and analyze radio propagation characteristics is developed. This program is able to control the measurement instruments including spectrum analyzer through GPIB interface and analyze the measured data to yield mean excess delay and RMS delay spread. The measured path loss can be compared with theoretical value in free space or inside a tunnel. The measured and analyzed results can also be presented in the forms of graphs. As these tasks can be conducted on the spot of the measurements, this program is very helpful in performing and verifying the measurements immediately. In this thesis radio propagation characteristics with frequency bands of 2.45 and 5.8GHz in subway tunnels are measured by using the program. Path loss and delay spread in subway tunnel is measured and compared according to the form of antenna beam and LOS(Line of Sight) and N-LOS(Non-Line of Sight).

• Korean Journal of Applied Biomechanics
• /
• v.26 no.4
• /
• pp.333-341
• /
• 2016

Objective: The purpose of this study was to assess the consistency of the gliding and push-off motion for single leg skating from the first to fourteenth steps. We hypothesized that: 1) there would be no difference in stroke trajectory, step rate, and cycle rate between the left and right steps of gliding; and 2) there would be a difference in the resultant velocity of toe push-off and the horizontal velocity of the center of mass after six step push-offs. Method: The study included five male 500-m speed skaters (mean height, $1.80{\pm}0.02m$; mean weight, $76.8{\pm}3.96kg$; record, $35.83{\pm}0.30sec$; 100-m record, <9.97 sec). Data were collected from the first to fourteenth steps (40 m) and recorded using five digital JVC GR-HD1KR video cameras (Victor Co., Japan) operating at a sampling frequency of 60 fields/sec and shutter speed of 1/500 sec. For each film frame, the joint positions were digitized using the KWON3D motion analyzer. Position data were filtered with low-pass Butterworth $4^{th}$ order at the cut-off frequency of 7.4 Hz. Results: The right toe of the skating trajectories at $2^{nd}$, $5^{th}$, and $7^{th}$ strokes differed from those of the left toe. The angles of the right and left knee demonstrated unbalanced patterns from the flexion and extension legs. The step and cycle rates of the right and left leg differed from the start until 20 m. The resultant velocities of the toe at the push-off phase and of the body mass center diverged before the six push-offs. Conclusion: This study's findings indicate that the toe of skating trajectory on left and right sliding after push-off should maintain a symmetrical trajectory. The resultant velocity of toe push-off and horizontal velocity from the center of body need to be separated after about six step push-offs.

• The Journal of Korean Academy of Orthopedic Manual Physical Therapy
• /
• v.16 no.2
• /
• pp.40-47
• /
• 2010

Purpose : To exam the effects of active ankle range of motion(ROM) exercise on sciatic nerve movement and provide the evidence that use it to patients with hypomobile sciatic nerve as a nerve mobilization technique. Methods : The subjects consist of 32 asymptomatic healthy adults(male; 15, female; 17) who have limited passive straight leg raising(PSLR) ranges below 70 degrees. First, examiner measures PSLR angles at three times. Then, subject was instructed perform the active ankle ROM exercise(dorsiflexion and plantarflextion) at limited angle. After each subject completed the active ankle ROM exercise, return the starting position and examiner measures the PSLR angles at three times again. Results : First, PSLR range was no significant differences between dominant and non-dominant leg(p >.05). Second, active ankle ROM exercise significantly increased PSLR range by mean of degrees(p <.05). Third, there was no learning effects among the measurement trials(p >.05). Conclusion : These data show that active ankle ROM exercise can mobilize the sciatic nerve. Therefore, it can be applied to patients with hypomobile sciatic nerve(sliding dysfunction) as a neural mobilization technique.

• Journal of Powder Materials
• /
• v.3 no.4
• /
• pp.271-278
• /
• 1996

In this study, the effect of the transition elements on the microstructure and mechanical properties of rapidly solidified Al-Mg-X alloys was investigated. As a result of the rapid solidification processing, fine equiaxed grains with a mean diameter of 2 $\mu$m were observed in these alloys. Many fine particles were found to be distributed rather homogeneously throughout the matrix with relatively large particles occasionally at grain boundaries. The ultimate tensile strengths of Al-Mg-X alloys were found to decrease rather remarkably at 150 $^{\circ}C$ without the gain of the ductility at 150 $^{\circ}C$, which may result from segregation of $\beta$ ($Al_{3}Mg_{2}$) precipitates. Fine dimples were observed on the fracture surfaces for all alloy systems and the variation of the size and shape of dimples was not observed upon alloy systems. The ductility at 530 $^{\circ}C$ was found to be ~100%, suggesting that grain boundary sliding did not contribute to ductiliy despite he grain size stabilization. The absence of superplastic behavior may be associated with low boundary misorientation in rapidly solidified Al-Mg-X alloys.

• Structural Engineering and Mechanics
• /
• v.31 no.6
• /
• pp.639-662
• /
• 2009

A comprehensive investigation of the stochastic response of an isolated cable-stayed bridge subjected to spatially varying earthquake ground motion is performed. In this study, the Jindo Bridge built in South Korea is chosen as a numerical example. The bridge deck is assumed to be continuous from one end to the other end. The vertical movement of the stiffening girder is restrained and freedom of rotational movement on the transverse axis is provided for all piers and abutments. The longitudinal restraint is provided at the mainland pier. The A-frame towers are fixed at the base. To implement the base isolation procedure, the double concave friction pendulum bearings are placed at each of the four support points of the deck. Thus, the deck of the cable-stayed bridge is isolated from the towers using the double concave friction pendulum bearings which are sliding devices that utilize two spherical concave surfaces. The spatially varying earthquake ground motion is characterized by the incoherence and wave-passage effects. Mean of maximum response values obtained from the spatially varying earthquake ground motion case are compared for the isolated and non-isolated bridge models. It is pointed out that the base isolation of the considered cable-stayed bridge model subjected to the spatially varying earthquake ground motion significantly underestimates the deck and the tower responses.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.20 no.1
• /
• pp.54-65
• /
• 1996

The purposes of this study were 1) to present the optimum slacks pattern for young men, 2) to develope a methodology to draft basic slacks pattern using AutoCAD The total crotch legth and the shape of the crutch line were determined by anthropometric data analysis. The total crotch length was calculated with the waist girth, the hip girth and the crotch length measurements. The anthropometric data utilized for this procedure was National Anthropometric Survey of Korea, 1992. And multidimensional anthropometric measurements were carried out for 6 male college students between the age of 18 to 24. The subjects were measured with the Martin's anthropometer and the sliding gauge. Mean, standard deviation and t-test were performed for statistical analysis of the data. The automatic drafting method was programmed by AutoLISP in AutoCAD. The automatic drafting was based on the Muller's slacks pattern drafting method, the measurements of slacks construction components and the curve of crotch line. The crotch line was drafted using of the arc function in AutoCAD. The total crotch length was calcuated using the multiple regression equation. The experimental pattern developed to accomodate individual body wleasurements expected to produce customized apparel production in QRS(Quick Response System) production system.

• Composites Research
• /
• v.13 no.4
• /
• pp.11-18
• /
• 2000

This study is mainly concerned with friction and wear properties for the piston ring of non-lubricating air compressor which made of PTFE-polyimide composites. At the PTFE and polyimide alone mixture specimens, PTFE80%-polyimide20%, which shows the lowest mean friction coefficient and specific wear rate at 0.94m/s sliding speed. In case of the specific wear rate, copper30% specimen shows the lowest value of 2.537-5(mm3/Nm) in all specimens. It considered that the friction coefficient is affected by generating speed and quantity of wear film. In case specific wear rate, it is attributed to the fact that the surface hardness of wear film is proportioned to specific wear rate.