• KIEAE Journal
• /
• 제7권1호
• /
• pp.23-31
• /
• 2007

This study aims to evaluate the illuminance performance of sloped light guide with automated venetian blind systems. For the purpose, a mock-up model was constructed as a prototype of Korean office building with $12.0m{\times}7.3m{\times}3.7m$ ($w{\times}d{\times}h$) and south facing side-window mounted between the clerestory window($2.0m^2$) and the view window($5.6m^2$). The light guide of 1.28m deepth and $29^{\circ}$ tilted angle, is covered with 0.6mm galvanized steel sheet and 97% reflective film. To protect the room from low solar angle, a blind systems, 0.15m deepth and $30^{\circ}$ automated slat angle was installed. To assess illuminance performance, the totally 37 measuring points for illuminance were monitored. For the detailed analysis, photometric sensors were installed at work-plane (8 points), wall (7 points), ceiling (3points), and exterior horizontal illuminance (1 point) respectively. The performance was measured under clear sky and is monitored by Agilent data logger, photometric sensor Li-cor and the Radiant Imaging ProMetric 1400. Comparisons of light factor and uniformity are discussed.

• 한국정보통신학회논문지
• /
• 제12권11호
• /
• pp.1923-1932
• /
• 2008

무인 운반설비의 자동화 시스템 개발의 한 부분으로써 여러 Vision 센서 중 레이저 센서를 이용하여 작업 공간상에 있는 판재류와 코일류의 경계부분을 인식한다. 다음으로 인식한 물체의 경계를 이용하여 3차원 공간상의 위치 좌표를 추출하여 무인크레인에 이동해야할 위치 좌표를 전달한다. 본 연구에서는, 첫 번째 레이저 센서를 이용한 물체의 경계 추출, 두 번째 레이저 센서의 z축 기울기 각 추출, 세 번째 인식한 경계를 이용하여 물체의 2차원 위치좌표 추출, 네 번째 레이저 센서를 이용하여 판재와 코일의 판별, 다섯 번째 물체 판별의 결과에 따른 판재 와 코일의 3차원 위치좌표 추출을 목적으로 한다. 본 연구의 결과는 무인 운반설비의 자동화 시스템 개발에 상당한 도움이 될 것으로 기대된다.

• Advances in aircraft and spacecraft science
• /
• 제2권3호
• /
• pp.329-343
• /
• 2015

This study aimed to observe the effect of a novel concept (referred to as the flap extension) implemented on the leading edge of the flap of a three element high lift device. The high lift device, consisting of a flap, main element and slat is designed around an Airbus research profile for sufficient take off and landing performance of a large commercial aircraft. The concept is realised on the profile and numerically optimised to achieve an optimum geometry. Two different optimisation approaches based on Genetic Algorithm optimisations are used: a zero order approach which makes simplifying assumptions to achieve an optimised solution: as well as a direct approach which employs an optimisation in ANSYS DesignXplorer using RANS calculations. Both methods converge to different optimised solutions due to simplifying assumptions. The solution to the zero order optimisation showed a decreased stall angle and decreased maximum lift coefficient against angle of attack due to early stall onset at the flap. The DesignXplorer optimised solution matched that of the baseline solution very closely. The concept was seen to increase lift locally at the flap for both optimisation methods.

• KIEAE Journal
• /
• 제15권1호
• /
• pp.83-88
• /
• 2015

This study aims to develope the light-weight PV blinds with windows and to investigate the shading analysis by the control conditions. For the study, the polycarbonate characteristics and coating methods are analyzed and the PV blind design for a small office is suggested. Also, the mock-up model of a suggesting system was made. The field tests were controled based on a solar altitude under clear sky conditions. As results, it is necessary to use a polycarbonate instead of a tempered glass for a light-weight PV. The shading effects of blind systems are high in slat angle $30^{\circ}$ and low in $0^{\circ}$. Also, the shading ratio is more affected by solar latitude than solar altitude. The shading change rate is relevantly constant on the solar altitude.

• International Journal of Aeronautical and Space Sciences
• /
• 제8권2호
• /
• pp.28-36
• /
• 2007

A multi-objective design exploration for a three-element airfoil consisted of a slat, a main wing, and a flap was carried out. The lift curve improvement is important to design high-lift system, thus design has to be performed with considered multi-angle. The objective functions considered here are to maximize the lift coefficient at landing and near stall conditions simultaneously. Kriging surrogate model which was constructed based on several sample designs is introduced. The solution space was explored based on the maximization of Expected Improvement (EI) value corresponding to objective functions on the Krigingmodels. The improvement of the model and the exploration of the optimum can be advanced at the same time by maximizing EI value. In this study, a total of 90 sample points are evaluated using the Reynolds averaged Navier-Stokes simulation(RANS) for the construction of the Kriging model. In order to obtain the information of the design space, two data mining techniques are applied to design result. One is functional Analysis of Variance(ANOVA) which can show quantitative information and the other is Self-Organizing Map(SOM) which can show qualitative information.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 추계학술발표대회 논문집
• /
• pp.256-263
• /
• 2011

Recently, curtain wall structure is constructed according to increasing high rise building. Glass is usually used in opening of curtain wall structure and window area ratio is finally increased. Excessive Daylighting and solar radiation by large window area ratio cause discomfort glare and add to cooling load in the case of office that is heavy on lighting and cooling. Therefore, this study suggests to use low transmittance window for solve those problems. Indoor lighting environment and building energy performance were analyzed by increasing transmittance from 10% to 90% and comparing fixed venetian blind. Consequently, the range of transmittance that is possible to daylighting and prevent discomfort glare. Secondary energy consumption is efficient in the case that transmittance is the range of from 20% to 50%, primary energy consumption is nice on from 20% to 40%. If those result put together, the range of window transmittance from 30% to 50% is proper in the office in lighting environment and energy consumption aspects.

• KIEAE Journal
• /
• 제12권6호
• /
• pp.113-121
• /
• 2012

A hospital is the most important infra-facility of the places which take care of people's body in social environment. There exist several environmental factors in the ways to heal the human body in hospital ward, but this study tried to look into the improvable pleasant sickroom environment with focus on light environment among the factors. In other words, this study aims at the research on proper daylight inflow into sickroom space as basic data for understanding the link between healing environment and natural lighting. In the simulation analysis through this research, this study completed the initial simulation using Autodesk Revit 2011 with focus on two types of individual multi-bed room units of the two general hospitals located in Gwangju City. This study made a simulation analysis of The two multi-bed rooms looking to the west using the weather data on Gwangju district, which is the strong point of ECOTECT2011. Conclusively, looking into the analysis of the simulation model in time of attaching the length of in & outside light shelf, the angle controlling of light shelf, the daylight factor and DA were found to show the tendency to decrease in the numerical value due to the decrease in sunlight inflow as the simulation model moved more toward the room from the window in comparison with the existing analysis of multi-bed rooms. Particularly, this study was able to read that the daylight factor and DA were more decreasing to improve at the light shelf than the existing bedrooms; conclusively, this study judges that the natural lighting simulation analysis could be helpful in improving the healing environment as basic data.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.291-298
• /
• 2019

In order to study the mechanical properties of rock salt, triaxial compression tests under different temperatures and confining pressure are carried out on rock salt specimens, the influence of temperature and confining pressure on the mechanical properties of rock salt was studied. The results show that the temperature has a deteriorative effect on the mechanical properties of rock salt. With the increase of temperature, the peak stress of rock salt decreases visibly; the plastic deformation characteristics become much obvious; the internal friction angle increases; while the cohesion strength decreases. With the increase of confining pressure, the peak stress and peak strain of rock salt will increase under the same temperature. Based on the test data, the Duncan-Chang constitutive model was modified, and the modified Duncan-Chang rock salt constitutive model considering the effect of temperature and confining pressure was established. The stress-strain curve calculated by the modified model was compared with the stress-strain curve obtained from the test. The close match between the test results and the model prediction suggests that the modified Duncan-Chang constitutive model is accurate in describing the behavior of rock slat under different confining pressure and temperature conditions.

• 한국축산시설환경학회지
• /
• 제11권3로
• /
• pp.153-160
• /
• 2005

비육돈사의 돈방바닥 형태와 출하체중 증가가 체중 80kg 이상 버크션종 비육돈의 생산효율과 도체품질 및 육질특성에 미치는 영향을 조사하기 위하여 총 444두를 공시하여 시험을 수행하였다. 비육돈사 돈방바닥 형태는 콘크리트 슬랏바닥과 톱밥바닥으로 하여 비교하였으며, 출하체중은 관행으로 시행중인 110kg과 130kg으로 체중을 늘릴 경우를 비교하였는데, 사료섭취량, 증체량 및 사료요구율 등 생산효율과 부분육 생산량 비교 및 등심근 pH, 보수성, 육즙 손실, 전단력, 육색과 같은 육질특성을 조사, 비교하였으며, 그 결과를 요약하면 다음과 같다. 1 돈방바닥 형태와 출하체중 증가는 사료 섭취량과 증체량 및 사료요구율에 영향을 미치지 않는 것으로 나타나 출하체중을 130kg으로 증가시키거나 돈방바닥을 톱밥으로 처리하여도 생산효율 차이는 인정되지 않았다. 2. 출하체중 증가는 부분육 생산량을 비례적으로 증가시키는 것으로 나타났으며, 특히 삼겹살 부위 생산량이 상대적으로 크게 증가하는 것으로 조사되었으나 등지방두께는 차이가 없었다. 그러나 돈방바닥 형태에 의한 부분육 생산량 차이는 인정되지 않았다. 3. 돈방바닥 형태와 출하체중 증가는 돈육 등심근의 수분 함량, pH, 보수성, 육즙 손실 및 전단력에 영향을 미치지 않는 것으로 나타났으며, 출하체중 110kg과 130kg 간 및 콘크리트 슬랏 바닥과 톱밥바닥 간에 등심근의 육질특성의 차이가 인정되지 않았다. 4. 출하체중은 돈육 등심근의 밝기를 나타내는 명도 값과 황색도 값에는 영향을 미치는 것으로 나타났으나 적색도 값에는 영향을 미치지 않는 것으로 나타났으며, 돈방바닥 형태에 의한 돈육 등심근의 명도, 적색도 및 황색도 차이는 인정되지 않았다.신의 숭고한 고유-독창성(Originality)이 피드백의 경로를 투과하면서 자신을 남에게 투영시켜 얻어내는 것이 고유성의 변종이다. 피드백은 단순한 작품의 일부가 아니라 작품을 이루는 뼈대이다 기술의 과시만으로는 예술의 행위가 될 수 없다. 작가의 예술성이 관객의 감성에 피드백 되도록 노력해야 한다 그러기 위해서는 예정된 피드백이란 느낌을 관객이 갖지 않도록 하여야 한다. 인터렉티브 미디어 아트는 초기의 형태에서 벗어나 새로운 집적된 피드백 기술로 전환하여야 할 시기가 온 것이다.료된다.시한 개체의 수술 전 방사선학적 평균 고관절 등급은 양측 모두 $3.2\pm0.9$이었고 수술 직후의 좌 우측 평균 고관절 등급은 각각 $2.7\pml.1,\;2.7\pm0.9$ (n=36) 이었다. 수술 직후와 2, 4, 8, 12, 24주 후의 고관절 등급이 수술 전에 비하여 유의적으로 개선된 것을 확인하였다.(P<0.01). 수술 후 정기적인 검사 시에 측정한 Norberg angle, percentage of femoral head coverage도 수술 전과 비교해 유의성 있게 증가하였다(P<0.01). 변형 3중 골반 절골술 직후의 평균 골반직경은 수술 전의 골반직경보다 유의적으로 증가하였으며(P<0.01)(n=36) 수술 후 평균 9.3L2.7주에 절골선 유합이 종료되었다(n=21). 반면 편측 3중 골반 절골술을 실시한 경우에는 수술 후 골반경이 수술 전과 비교해 증가하지 않았다. 변형 3중 골반 절골술후에 장액종 형성(1마리), 스크류 변위(4마리), 스크류 부러짐(1마리), 편측성 신경마비(1마리) 등의 부작용이 발생하였다. 이상의 결과를 토대로, 변형 3중