• Steel and Composite Structures
• /
• 제45권6호
• /
• pp.831-837
• /
• 2022

Numerical investigation on dynamic characteristics of sandwich plates under periodic and thermal loads has been presented by assuming that the plate has three layers which are a foam core and two skins. The foam core made of Aluminum has porosities with uniform and graded dispersions. The sandwich plate has been supposed to be affected by periodical compressive loads. Also, temperature variation causes uniform thermal load. The formulation has been established based upon a higher-order plate theory and Ritz method has been used to solve the equations of motion. The stability boundaries have also been obtained performing Bolotin's method. It will be indicated that stability boundaries of the sandwich plate depend on periodical load parameters, porosities, skin thickness and temperature.

• Structural Engineering and Mechanics
• /
• 제78권5호
• /
• pp.611-622
• /
• 2021

Composite material-due to low density-causes weight savings, which results in lower fuel consumption of transport vehicles. The aim of the research was to change the existing base-plate of the aluminum airplane container with the composite sandwich plate in order to reduce the weight of the containers of cargo aircrafts. The newly constructed sandwich plate consists of aluminum honeycomb core and composite face-sheets. The face-sheets consist of glass or carbon or hybrid fiber layers. The orientations of the fibers in the face-sheets were 0°, 90° and ±45°. Multi-objective optimization method was elaborated for the newly constructed sandwich plates. Based on the design aim, the importance of the objective functions (weight and cost of sandwich plates) was the same (50%). During the optimization nine design constraints were considered: stiffness, deflection, facing stress, core shear stress, skin stress, plate buckling, shear crimping, skin wrinkling, intracell buckling. The design variables were core thickness and number of layers of the face-sheets. During the optimization both the Weighted Normalized Method of the Excel Solver and the Genetic Algorithm Solver of Matlab software were applied. The mechanical properties of composite face-sheets were calculated by Laminator software according to the Classical Lamination Plate Theory and Tsai-Hill failure criteria. The main added-value of the study is that the multi-objective optimization method was elaborated for the newly constructed sandwich structures. It was confirmed that the optimal new composite sandwich construction-due to weight savings and lower fuel consumption of cargo aircrafts - is more advantageous than conventional all-aluminum container.

• 대한기계학회논문집B
• /
• 제21권7호
• /
• pp.939-947
• /
• 1997

An experimental study of the skin friction measurement in a turbulent boundary-layer has been carried out. The skin friction measurements are made using the laser interferometer skin friction (LISF) meter, which optically detects the rate of thinning of an oil applied to the test surface. This technique produces reliable skin friction data over a wide range of flow situations up to 3-dimensional complicated flows with separation, where traditional skin friction measurement techniques are not applicable. The present measured data in a turbulent boundary-layer on a flat plate using the LISF technique shows a good comparison with the result from the previous velocity profile techniques, which proves the validity of the present technique. An extensive error analysis is carried out for the present technique yielding an uncertainty of about .+-.8%, which makes them suitable for CFD code validation purposes. Finally the measurements of the skin friction in a separated region after a surface-mounted obstacle are also presented.

• Radiation Oncology Journal
• /
• 제10권1호
• /
• pp.107-113
• /
• 1992

4-5MeV의 전자선은 피부표면의 흡수선량을 증가시키고 표면하 10mm 내외에서 급속히 감소함으로 Mycosis fungoides, Kaposi's sarcoma등 전신피부암에 대한 가장적당한 치료방사선으로 알려져왔다. 그러나 평면이 아니고 굴곡이 심한 인체표면에 균일한 선량을 계획하기는 많은 어려움이 있었다. 연세암센터에서는 1980년부터 시행하여왔던 6MeV 전자선의 마름모형, 네방향 조사방법을 개량하고 많은 문헌을 참고하여 상하 양방향의 조사면과 환자위치를 각각 여섯가지 자세로 나누어 조사(Six-Dual-Field)하는 방법을 사용하였으며 이에따른 전신피부표면의 선량과 선량분포를 측정하였다. 선형가속기에서 발생되는 6MeV 전자선을 0.5 cm 두께의 아크릴판으로 감약시키고 콜리메터가 완전히 열린 조사면을 상하 $19^{\circ}$씩 옮기므로서 타겟트에서 3m 거리에 약 $2m{\times}1m$의 균일한선량의 조사면(평탄도 $+3\%$)과 10 mm 내외의 실효깊이 ($80\%$, 선량지점) 및 산란선에 의한 피부표면선량을 증가시킬 수 있었다. 환자는 일부피부가 가려지지 않도록 팔과 다리를 적당한 자세로 고정시키고 전자선을 여섯방향에서 각각 2회씩 상하로 조사시키므로서 피부표면에 균일한 선량분포(표준편차 $5\%$)가 가능하였으며 $80\%$,의 심부율이 $8\~10mm$에서 측정되었다. 모든 측정은 인체등가팬텀과 폴리스틸렌팬텀을 사용하였으며 필름, 평형전리측정기 및 표준전리측정기를 이용하였다. 특히 환자피부표면의 흡수선량분포를 확인하기 위하여 열형광측정기와 반도체측정기를 이용하였으며 $6\~20$개의 소형 측정기를 환자 피부표면에 부착시킨후 전자선 치료과정 동안 피폭 시켜 측정하였고 그결과 차폐된 부위를 제외하고 평균 $10\%$, 이 내의 균일한 선량분포를 얻을수 있었다.

• Journal of Acupuncture Research
• /
• 제17권3호
• /
• pp.45-56
• /
• 2000

Objectives : Meridian Scraping Therapy(MST: Kwal-Sa: 刮痧) has not well known in Korea. But it's a kind of Traditional Physical Therapy wide spreaded in China and Taiwan. So I want to introduce this new Therapy by summarizing the basic theories and practical manipulations. Conclusions : To analyse the meaning of the character Kwal-Sa, Kwal(刮) means scraping the skin by some tools and Sa(痧) means originally the red spots on skin of measles but in this therapy it's the red spot on skin after the treatment. Meridian Scraping Therapy is based on the meridiology and holism which are the basic theory of Oriental Medicine. The main effects of Meridian Scraping Therapy are draining of pathogenic factors, promoring the flow of ki and blood, tonify yang, balancing the harmony of intemal organs and enhancing the immuno-ability in body. Rhinoceros corpus is common matrial of MST-plate which is the tool of manipulation. And by this plate several manipulation is performed according to the symptom and the locations of pain. The merits of MST are that easily learned by practician, the effects of the treatment are very quickly manifest and no significant side-effects. And additionally this therapy performed not only for treat diseases but prevent it and preserve health.

• Journal of Biosystems Engineering
• /
• 제20권1호
• /
• pp.58-65
• /
• 1995

A numerical study for a two dimensional multi-jet with crossflow of the spent fluid has been carried out. Three different distributions of mass-flow rate at 5 jet exits were assumed to see their effects upon the flow characteristics, especially in the jet-flow region. For each distribution, various Reynolds numbers ranging from laminar to turbulent flows were considered. Calculations drew the following items as conclusion. 1) The development of the free jets issued from downstream jets was hindered by the crossflow formed due to jets. Consequently, the free jet was developed into the channel flow without any evident symptom of impingement jet flow characteristics 2) The crossflow induced the pressure gradient along the cross section of jet exits and the value of the pressure gradient increased as going downstream. The crossflow generated also the turbulent kinetic energy as it collied with the downstream jets. 3) The skin friction coefficient along the impingement plate was affected more by the distribution of mass flow rate at jet exits rather than by the Reynolds number. The skin friction coefficient was inversely proportional to the square root of the Reynolds number, regardless of flow regime when a fully developed flow was formed in the jet flow region. 4) The distribution of the skin friction coefficient along the impingement plate was found to be controlled by adjusting the distribution of mass flow rate at jet exits.

• 한국주조공학회지
• /
• 제5권4호
• /
• pp.283-288
• /
• 1985

The melt of highly purified Zn was poured by top pouring process into the open green sand mold, that was made by using the 3-plane L-sections pattern. After skin was formed, the unsolified melt was poured out by rolling-over. The thicknesses of skin for each different of castings were investigated with one dimension. The results obtained and could be summerzed as follows: 1) While the 3-plant L-sections castings were solidifying in the mold, solidification blocks of different section modulus in the castings were formed, i.e. 1-dimension divergency block, 2-dimension heat divergency block, 3-dimension heat divergency block, 2-dimension heat convergency block, and 3-dimension heat convergency block. 2) When the chill plate was set up to the mold in order to change section modulus artificially, heat divergency blocks and heat convergency blocks according to the shape of chill plate were revealed.

• Journal of the Korean Society for Industrial and Applied Mathematics
• /
• 제12권4호
• /
• pp.201-202
• /
• 2008

Because of the importance of suction or injection in the fields of aerodynamics, space science and many other industrial applications, our present study is motivated. The effect of natural convection on MHD flow past a vertical plate with suction or injection is studied. We have tried to solve the dimensionless governing equations by using finite difference scheme. To ensure the validity of our numerical solutions, we have compared our numerical solutions for temperature and velocity for the case of suction and injection for unit Prandtl number with the available exact solutions in the literature. The corresponding codes were written in Mathematica 5.0 for calculating numerical solutions for temperature and velocity and the comparison between the exact and numerical solutions. For the purpose of discussing the results some numerical calculations are carried out for non-dimensional temperature T, velocity u, skin friction ${\tau}$ and the Nusselt number $N_u$, by making use of it, the rate of heat transfer is studied.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제28권3호
• /
• pp.231-233
• /
• 2002

Temporary reconstruction of the mandibular continuity defect resulting from the ablative tumor surgery with a reconstruction plate can be used for the preservation of normal facial contour and oral function and for periodic follow up of recurrence. Reconstruction plates are adapted to the bone before the resection and provisionally fixated with some screws. Accurate contouring and adaptation are very important for the prevention of displacement of bony stumps and decubituous skin ulcer. However, if there is large expanding buccal tumor mass in mandible, it is very difficult or even impossible to contour the plate before resection. I, therefore, introduce the reconstruction plate application technique using a simple condylar repositioning miniplate after segmental mandibular resection.

• 대한기계학회논문집B
• /
• 제22권9호
• /
• pp.1335-1348
• /
• 1998

Flow characteristics in transitional boundary layers on a flat plate were experimentally investigated under three different freestream conditions i. e. uniform flow with 0.1 % and 3.7% freestream turbulent intensity and cylinder-wake with 3.7% maximum turbulent intensity. Instantaneous streamwise velocities in laminar, transitional and turbulent boundary layers were measured by I-type hot-wire probe. For estimation of wall shear stresses on the flat plate, measured mean velocities near the wall were applied to the principle of Computational Preston Tube Method (CPM). Distributions of skin friction coefficients were reasonably predicted in all developed boundary layers. Intermittency profiles, which were estimated using Conditional Sampling Technique in transitional boundary layers, were also consistent with previously published data. It was predicted that the incoming turbulent intensity had more influence on transition onset point and transition process than freestream turbulent intensity existed just over the transition region. It was also confirmed that non-turbulent and turbulent profiles in transitional boundary layers could not be simply treated as Blasius and fully turbulent profiles.