• 한국압력기기공학회 논문집
• /
• 제11권2호
• /
• pp.20-24
• /
• 2015

During refueling Outage, In-service inspections(ISIs) for the Nuclear Power Plant components are mandatory requirement in accordance with ASME Code Sec. XI. Especially, in current ultrasonic testing is one of the most important NDT techniques that are used for volumetric examination methods for nuclear power plant components, and accurate sizing of flaw indication by UT is essential to assure the integrity of the components. However, ASME code specifies minimum requirement for vessel examination procedure, and so far many different flaw sizing approaches have been tried to apply. Through the Round Robin Test(RRT), the accuracy of ultrasonic flaw sizing using DAC techniques was measured with the mock-ups simulating typical pressure vessel welds. These mock-ups contain artificially introduced flaws of known size and location. This paper shows experimental comparison data on the accuracy of techniques using such as 6dB drop, 50%DAC, 20%DAC and 20%DAC with beam spread correction, and also shows that diverse DAC techniques can be effectively applied to the assessment of the flaw sizing for pressure vessel welds in the stage of welding and fabrication.

• 한국압력기기공학회 논문집
• /
• 제9권1호
• /
• pp.25-30
• /
• 2013

The periodic inspection of piping and pressure vessels welds in nuclear power plant has to provide reliable result related to weld flaws, such as location, maximum amplitude response, ultrasonic length, height and finally the nature or flaw pattern. The founded flaw in ultrasonic inspection is accepted or rejected based on these data. Specially, the amplitude of flaw response is used as basic parameter for flaw sizing and it may cause some deviation in length sizing result. Currently the ultrasonic inspections in nuclear power plant components are performed by specific inspection procedure which describing inspection technique include inspection system, calibration methodology and flaw characterizing. To perform ultrasonic inspection during in-service inspection, reference gain should be established before starting ultrasonic inspection by the requirement of ASME code. This reference gain used as basic criteria to evaluate flaw sizing. Sometimes, a little difference in establishing reference gain between calibration and field condition can lead to deviation in flaw sizing. Due to this difference, the inspection result may cause flaw sizing error. Therefore, the objective of this study is to compare and evaluate the ultrasonic amplitude difference between air filled and water filled pipe in nuclear power plant. Additionally, the accuracy of flaw sizing is estimated by comparing both conditions.

• 한국의류학회지
• /
• 제26권7호
• /
• pp.1015-1025
• /
• 2002

This study is aimed at investigating and developing the use and sizing system of the apparels listed in on-line and catalog shopping in Korea. This is a basic study for an apparel sizing system to be developed, which could be used to approach consumers more easily and provide improved fitness and accuracy in terms of size and style of apparels for fashion E-commerce. A survey was conducted among the consumers who are more than 18-years-old and purchased more than two times the apparels listed in on-line and catalog shopping of two selected catalog shopping enterprises, and its statistical results are analysed from 281 respondents' questionnaires. The results of the study are as follows: 1. According to the result of the survey on the use and sizing system of the apparels listed in. on-line and catalog shopping, the consumers who purchased once apparels continue doing so in the same manner. A catalog shopping is the most preferred form of shopping. The most dissatisfying part in purchasing apparels is a poor quality of 'texture', and the second biggest problem is about 'size'About 51.2 percent of the apparels were not worn or even returned, while the top reason for that is 'Inappropriate size' and 'color', and 'texture'comes next on the list. 2. According to the survey on the recognition-rate concerning common' body size, most respondents were aware of their height and weight, and So percent of respondents said that they were aware of their waist circumference. But, chest circumference and hip circumference were recognized only by 58.4 percent and 35.6 percent of respondents, respectively. 3. According to the survey on difference between men and women, the male consumers have less aware of hip circumference than the female counterparts. The females have much more dissatisfaction with apparel sizing system and show higher return-rate of purchased apparels than the males.

• Nuclear Engineering and Technology
• /
• 제46권6호
• /
• pp.883-888
• /
• 2014

This work presents the influence of noise originating from the tube itself on the detectability and sizing accuracy for laboratory-induced outer diameter axial cracks in nuclear steam generator tubes. The variations of signal amplitude and phase angle of the same cracks were analyzed when increasing the signal-to-noise ratio of the tube itself from 9 to 18. It was experimentally verified that the detectability for small cracks was enhanced by increasing the signal-to-noise ratio. The phase angle also rotated to a value representing the actual position and depth of a crack when increasing the signal-to-noise ratio.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.216-227
• /
• 2005

The head penetrations for control rod drive mechanism and instrumentation systems are installed at the reactor pressure vessel head of PWRs. Primary coolant water and the operating conditions of PWR plants can cause cracking of these nickel-based alloy through a process called primary water stress corrosion cracking (PWSCC). Inspection of the head penetrations to ensure the integrity of the head penetrations has been interested since reactor coolant leakages were found at U. S. reactors in 2000 and 2001. The complex geometry of the head penetrations and the very low echo amplitude from the fine, multiple flaws due to the nature of the see made it difficult to detect and size the flaws using conventional pulse-echo UT methods. Time-of-flight-diffraction technique, which utilizes the time difference between the flaw tips while pulse-echo does the flaw response amplitude from the flaw, has been selected for this inspection for it's best performance of the detection and sizing of the head penetration see flaws. This study defines the limits of the detectable and accurately sizable minimum flaw size which can be detected by the General TOFD and the Delta TOFD techniques for circumferentially and axially oriented flaws respectively. These results assures the reliability of the inspection techniques to detect and accurately size for various kind of flaws, and will also be utilized for the future development and qualifications of the TOFD techniques to enhance the detecting sensitivity and sizing accuracy of the flaws of the reactor head penetrations in nuclear power plants.

• 한국의류산업학회지
• /
• 제11권3호
• /
• pp.437-444
• /
• 2009

According to the activation of the fashion electronic commerce, this research investigated the merits and demerits and improvement plan of the 3D virtual try-on technology using the qualitative research method. This research was performed by interview with 70 evaluation group. The evaluation group of 3D virtual try-on was organized and the fit evaluation process by 3D human body scan and the 3D virtual try-on of the i-Fashion technology center were experienced. This study was performed by interview after the actual and virtual try-on about the casual shirt. The convenience and accuracy of measurement, usability in online shopping, body evaluation, complement of sizing system, and body shape management were discovered as merits. The requirement of high accuracy in sizing and avatar, limits of fabric expression, practical limitation by cost, vexatious of measurement garment, differences between real and virtual fittings, personal information leakage risk, and etc were pointed out as demerits. The mass customization, customized garment connected with medical service, humanized avatar, improved fitting report, entertainment, coordination, wardrobe manager were proposed as improvement plan.

• 한국전산구조공학회논문집
• /
• 제15권3호
• /
• pp.453-462
• /
• 2002

건설공사의 설계와 시공에서 표준화된 이산형 강재단면을 이용하고 있으나, 대부분의 최적화기법에서는 표준강재단면을 사용하기 위해 별도의 이산화 과정을 가지게 되므로 설계결과의 최적성을 보장할 수 없다. 따라서, 본 논문에서는 제안된 알고리즘의 효율성을 높이기 위해 전체구조계와 구조요소계로 나누는 다단계 알고리즘을 적용하였다 수치해석 과정의 효율성과 최적해의 정확성을 예제를 통하여 비교·검토하였다.

• 소성∙가공
• /
• 제9권5호
• /
• pp.478-485
• /
• 2000

This study aims to Improve the productivity in forming of flanged thrust engine bearings from two kinds of laminated sheet materials by integrating the forming processes or by reducing the number of the subsequent sizing and machining processes or by modifying the forming tools used. For steel-Al rolled blank, a design scheme for the one-step forming operation and the geometry of the tool set required is suggested and is verified its usefulness by the finite element simulation. And for steel-Cu sintered blank, the results of experiment and finite element analysis show that it is possible to improve the dimensional accuracy of formed products and to reduce the number of sizing processes just by modifying the shape and dimensions of initial blanks and flange forming dies, and by controlling the spring force.

• 소성∙가공
• /
• 제9권6호
• /
• pp.615-623
• /
• 2000

The industrial application of hydroforming has a great potential in saying cost and achieving dimensional accuracy in automotive industry presently. The aim of the following article is to investigate the effect of process parameters on hydroformed part. Firstly, we have to investigate the change of mechanical properties for sheet and pipe material according to various radius/thickness ratio(r/t). The change of mechanical properties affects the yield stress more than the total elongation. Increase of yield stress for pipe has a bad influence on formability of hydroforming. Among the roll-forming process, the sizing process didn't change mechanical properties. The process parameters such as the initial pressure, mandrel shape and friction have seriously influenced on formability of hydroforming. Therefore we need to check formability of given material through the FE analysis in the beginning stage of process design and the predicted hydroforming process parameters ate generally a good starting point for the prototype tryout stage. The results of pretending, hydroforming analysis using FE model are good agreement with experimental results.

• Asia pacific journal of information systems
• /
• 제8권3호
• /
• pp.101-118
• /
• 1998

The purpose of this study is to construct a value-oriented sizing and cost estimation model for system integration projects. In particular, this study is to build a system architecture design and integration cost model, and a network design and implementation cost model. Unlike software development projects, system integration projects include knowledge-intensive professional services on system architecture and network design areas. Because of these work's high invisibility, the cost of these services is hard to estimate and measure. Therefore, we need to develop value-oriented cost models. This study presents 6 value-oriented cost models, and tests statistical significance of these models with real system integration project data. The results show that cost factors on these models are valid, and models are statistically significant. Future work is needed to integrate various cost models and apply the whole model to field projects to increase model's prediction accuracy.