• Carbon letters
• /
• v.11 no.4
• /
• pp.293-297
• /
• 2010

To investigate new potential application of a clay material for C/C composites, illite added C/C composites were prepared with various illite contents. The improvement of filler effect by illite size reduction was also investigated using wet ballmilling by evaluating illite/phenolic resin infiltration using bulk density and porosity measurements, chemical structural changes of the composites using XRD, and thermal oxidation stability in air of the composites using TGA. The size reduction of illite resulted in narrower particle size distribution and improved illite infiltration into carbon preform. And the resultant C/C composites prepared with illite had even more improved thermal oxidation stability in air, showing more increased IDTs up to $100^{\circ}C$, compared to those of the C/C composites with pristine illite, due to the SiC formation through carbothermal reduction between illite and carbon materials. The illite induced delay in oxidation of the illite-C/C composites was also observed and the delayed oxidation behavior was attributed to the layered structure of illite, which improved illite/phenol resin infiltration. Therefore, the potential use of illite as filler to improve oxidation stability of C/C composite can be promising. And the size reduction of illite can improve its effect on the desired properties of illite-C/C composites even more.

• Journal of the military operations research society of Korea
• /
• v.25 no.1
• /
• pp.133-140
• /
• 1999

Preprocessing for the -01 integer programming can reduce the size of problem instance as well as tighten its linear programming relaxations. In this research, the preprocessing techniques are classified into two categories. First, for the reduction of problem size, there are variable fixing and constraint elimination techniques. Second, for the reduction of feasible region, there are coefficient reduction and Euchidean reduction techniques. These methods are implemented and the effects are shown by experimental results.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.217-222
• /
• 2004

The aim of this paper is to investigate the effect of micro-dimple size on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 is recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.1
• /
• pp.110-116
• /
• 2012

This paper proposes a new diversity antenna which is the base of MIMO, tunable and reconfigurable antennas. The antenna has a small size and high inter-antenna isolation resulting from the compact radiating element comprising a meandered line and an open-loop combined in one limited uniplanar space and a modified T-shaped decoupling structure, respectively. In a WiMAX band, the radiating element and the entire antenna are $0.092{\lambda}$ and $0.2216{\lambda}$ in size, which shows effective size-reduction and the gain and efficiency of the proposed antenna attached to the ground of a handheld device are 3.7dBi and 56% acceptable to the industrial standard.

• Journal of The Korean Society of Integrative Medicine
• /
• v.7 no.3
• /
• pp.149-157
• /
• 2019

Purpose : This study aims to check the relationship between the size of curvature in scoliosis patients and the reduction rate of curvature after wearing a brace and the relationships of the size of curvature and correction angle with Body Mass Index (BMI). Methods : With 30 adolescent girls who had never worn a brace, their Cobb angle and BMI were measured before manufacturing braces, and their corrected Cobb angle was measured after wearing the manufactured scoliosis braces. Results : The size of the major curvature before wearing the brace and the reduction rate of the curvature after putting it on had a negative correlation in both the major curvature (r=-.465, p<.01) and the minor curvature (r=-.516, p<.01). The size of the minor curvature and the reduction rate of the minor curvature before and after putting it on also had a negative correlation (r=-.429, p<.05). As for the relationship between the size of curvature and BMI, they had a negative correlation in both the major curvature (r=-.141) and the minor curvature (r=-.123), and as for the relationship between the reduction rate of curvature and BMI after wearing the brace, they had a positive correlation in both the major curvature (r=.251) and the minor curvature (r=.136); however, it was not statistically significant (p>.05). Conclusion : In conclusion, the larger the size of curvature, the lower the reduction rate of curvature after wearing the brace became. The larger the size of curvature, the lower the BMI became. The higher the BMI, the higher the correction ratio of the brace became. Therefore, it is judged that it is necessary to provide early treatment and manage body composition before scoliosis progresses.

• Nuclear Engineering and Technology
• /
• v.28 no.4
• /
• pp.366-372
• /
• 1996

The simulated spent PWR fuel pellet which is corresponding to the turnup of 33,000 MWD/MTU is prepared by adding 11 fission-product elements to UO$_2$. The simulated spent fuel pellet is treated at 40$0^{\circ}C$ in air (oxidation), at 110$0^{\circ}C$ in air (high-temperature treatment), and at $600^{\circ}C$ in hydrogen (reduction). The product is treated through additional addition and reduction up to 3 cycles. Pellets are completely pulverized by the first oxidation, and the high-temperature treatment causes particle and crystallite to grow and surface to be smooth, and thus particle size significantly increases and surface area decreases. The reduction following the high-temperature treatment decreases much the particle size by means of the formation of intercrystalline cracks. The particle size decreases a little during the second oxidation and reduction cycle and then remains nearly constant during the third and fourth cycles. Surface area of pounder increases progressively with the repetition of oxidation and reduction cycles, mainly due to the formation of Surface cracks. The degradation of surface area resulting from high-temperature treatment is restored by too subsequent resulting oxidation and reduction cycles.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.4
• /
• pp.309-314
• /
• 2018

Size reduction is an important pre-processing operation for utilizing biomass as a sustainable resource in industrial-scale energy production and as a raw material for other industries. This work investigates the size reduction characteristics of air-dried Miscanthus sacchariflorus Goedae-Uksae 1 (Amur silver grass) via image processing and identifies the morphological characteristics of comminuted and screened M. sacchariflorus. At chopping lengths of 18, 40, 80, and 160 mm, 81%, 77%, 78%, and 76% of the particles, respectively, passed through a 4-mm sieve. Even a knife mill with a very small screen aperture (>1 mm) admitted over 10% of the particles. The average circularity and aspect ratio of the particles were <0.30 and >10, respectively. These results confirm that in all preparation modes, most M. sacchariflorus particles were needle-like in shape, irrespective of the type of preparation.

• Textile Coloration and Finishing
• /
• v.23 no.2
• /
• pp.146-153
• /
• 2011

Silver nano-particles have been synthesized by liquid phase reduction method and alcohol reduction process. Silver nano-particles of the size 30 ~ 40 nm were formed successfully by alcohol reduction process. The formation, structure, morphology and size of silver nano-particles have been studied using FE-SEM, TEM, XRD, UV-visible spectroscopy. In particular high dispersion stability of the synthesized silver nano-particles could be obtained by PVP binding. Antibacterial activity of Ag/PET master batch sample made from its nano-silver particles showed excellent antibacterial activity against S. aureus and E. coli.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.554-554
• /
• 2012

Controlling the size distribution of gold nanoparticles (NPs) is of great importance due to the fact that their properties are strongly dependent upon the size distribution as well as the size itself. In the citrate reduction method for gold NP synthesis, the citrate works as (1) a reducing agent, (2) a surfactant, and also (3) a weak base: it raises the pH of the whole reaction mixture. Here, we have extensively studied the all three roles of the citrate, by adding other reagents separately (NaBH4, CTAB, and NaOH) for the independent control of the three roles of the citrate. Among the roles of the citrate, that as a weak base was found to be the most critical parameter affecting the size distribution of gold NPs and the size distribution became much more improved with the increase of the solution pH, while adding a supplementary surfactant or reducing agent resulted in the formation of less homogeneous NPs.

• Tribology and Lubricants
• /
• v.20 no.5
• /
• pp.266-271
• /
• 2004

The aim of this paper is to investigate the effect of surface texturing on reduction friction and to understand the potential of friction reduction through micro-scale dimple to fabricate by photolithography on pin-on-disk test using flat-on-flat contact geometry. It was verify that the friction property with respect to the same pitch has been influence on the size of dimple under lubricated sliding contact. Also, we can recognize from Stribeck curve that the friction property has a connection with the size of dimple. It can explain a relationship between the friction coefficient and a dimensionless parameter for lubrication condition. The friction property has been an effect on the size of surface texture on reduction friction, not only because the density of dimple, but also because the ratio of diameter/pitch. This ratio of approximately 0.5 recommend under the tested friction condition. It suggested that the ratio of d/p is an important parameter for surface texture design.