• International Journal of Reliability and Applications
• /
• 제13권1호
• /
• pp.49-56
• /
• 2012

Using total time on test transform (TTT), a new approach is taken for testing exponentiality versus the unknown age, exponential better than equilibrium life in convex ordering (EBELC). Selected critical values are tabulated for sample size n =2(2)50 and powers of the test are estimated for some commonly used distributions in reliability. Finally real example is presented to illustrate the theoretical results.

• 대한환경공학회지
• /
• 제22권3호
• /
• pp.575-585
• /
• 2000

서울지역의 질량 및 중금속 건식침적량과 대기중 입자의 입경분포를 1998년 7월부터 11월까지 건식침적판, 다단계 관성충돌 채취기(Cascade Impactor) 및 조대업자 채취기(Coarse Particle Sampler)를 사용하여 측정하였다. 인위적 오염원에 기인한 중금속(Cu, Mn, Ni, Pt, Zn)의 건식침적량이 주로 자연적 오염원에 기인한 중금속(Al, Ca)의 건식침적량에 비하여 약 10배에서 100배 정도 낮은 값을 나타내었다. 완전한 총 입자 및 중금속 입자의 입경분포는 입자 입경이 $10{\mu}m$보다 작은 영역에서 두 개의 peak를 보이고 $10{\mu}m$보다 큰 입자 영역에서 또다른 peak을 보이는 삼봉형(trimodal) 입경분포를 보여주었다. Sehmel-Hodgson 모델을 사용하여 건식침적속도를 추정하고 이를 이용하여 총 입자 및 중금속 입자의 건식침적량을 계산하기 위하여 다단계 모델(Multi-step model)을 사용하였다. 이 방법에 의하면, 건식침적량은 입자의 입경이 $10{\mu}m$보다 큰 입자들의 높은 건식침적속도에 의하여 크게 영향을 받고 이로부터 건식침적은 $10{\mu}m$보다 큰 입자들의 침적이 대부분을 차지한다는 것을 보여주었다. 측정된 입자의 입경분포와 추정된 건식침적속도를 이용하여 다단계 모델을 통하여 예측된 건식침적량은 직접 측정된 건식침적량과 비교하였을 때 잘 일치하였다.

• 한국주조공학회지
• /
• 제10권6호
• /
• pp.528-537
• /
• 1990

7XXX aluminum alloy powders produced by the self-manufactured rotating disc atomizer were investigated to determine the influence of the atomization parameters on the particle size distributions in air atmosphere. The particle size distributions are almost always bimodal with the dominant mode on the large particle size. Average powder size of 7XXX aluminum alloy is $74/{\mu}m~125/{\mu}m$ when melt is poured with the rate of 9g /sec at 730$^{\circ}C$ on a rotating disc of 30㎜ diameter at 6300rad/sec. The mass of finer particle increased when disc diameter, angular velocity, pouring temperature increased and pouring rate decreased. The powder shapes of bimodal change from acicular to tear-drop and from tear-drop to ligament with increasing powder size. Powder shape was determined by the atomization mechanism and oxidation in liquid state. Microstructure of powders appeared to be cell and cellular dendrite. The SDAS of Al-7.9wt%Zn-2.4wt%Mg-1.5wt%Cu-0.9wt%Ni Powders is $0.8{\mu}m~1.0{\mu}m$ for the powders of $size＋44{\mu}m~53{\mu}m$ and $1.6{\mu}m∼1.8{\mu}m$ for the powders of $size＋105{\mu}m~125{\mu}m$, repectively.

• Journal of the Korean Data and Information Science Society
• /
• 제23권1호
• /
• pp.53-61
• /
• 2012

많은 조사에서 표본 크기는 유의수준 또는 제1종 오류확률만을 고려하여 결정하였으나 최근에는 다양한 분야를 중심으로 제1종 오류확률뿐만 아니라 제2종 오류확률 또는 검정력을 함께 고려하여 표본 크기를 결정하는 경우가 늘어나고 있다. 이런 경향은 표본을 많이 얻을 수 없는 연구에서 더욱 뚜렸하다. 본 연구에서는 모평균과 모비율에 대한 검정에서 제1종 오류뿐만 아닌 제2종 오류를 고려한 경우 필요한 표본 크기를 결정하는 과정을 살펴보고 이를 웹사이트를 통해 공개하였다. 또한 주어진 표본 크기와 유의수준에 의한 검정력 계산도 함께 공개하였다.

• 한국정밀공학회지
• /
• 제19권4호
• /
• pp.117-123
• /
• 2002

X-ray diffraction observation of fracture surfaces yields useful information to analyze the causes of failure accidents of engineering structures. This experimental technique, named X-ray fractography, has been developed especially in metal and mechanical engineering fields. The distributions of the residual stress and the half value breadth of diffraction profiles beneath the fatigue fracture surface were measured with SNCM 439, HT100 and Ti-6Al-4V alloy. The size of the maximum plastic zone was successfully determined on the basis of the measured distributions. This size was correlated to maximum stress intensity factor. The distributions of the half value breadth of diffraction profiles on the fatigue fracture surfaces were measured with SNCM 439. HT100. The equations of x-ray parameter distribution were possible to estimated fracture parameters of fatigue fracture surfaces.

• 한국화재소방학회논문지
• /
• 제31권6호
• /
• pp.8-15
• /
• 2017

화재발생 시에 대부분의 인명 피해는 연기에 의해 발생되는데, 최근 건축 내장재에서 차지하는 플라스틱의 양이 많아지며 발생되는 연기의 유독성이 점차적으로 증가되고 있다. 연기에 의한 인체피해의 상당부분은 흡입연기의 폐침전과 관련이 있으며, 연기입자의 크기분포는 폐침전 특성에 직접적인 영향을 미친다. 따라서 플라스틱 종류에 따른 연기입자의 크기별 발생량 검토는 폐침전에 의한 인체피해 연구에 필수적으로 요구된다. 최근의 목재와 폴리프로필렌(PP)에 대한 연기입자의 발생특성 연구에서 PP의 연기입자 크기분포 특성이 몇 가지 측면에서 목재와는 확연히 다르게 나타났다. 이에 따라, 본 연구에서는 다른 플라스틱들도 연기입자 크기분포에서 PP와 같은 특성을 보이는지 알아보기 위해서 대표적인 4가지 플라스틱(LDPE, PA66, PMMA, PVC)에 대하여 연기입자 크기분포 측정실험을 수행하였다. 특정 조건에서 연소생성물을 균일하게 생성하고 분석하기 위하여 ISO/TS 19700 기준에 따른 등속튜브연소로를 이용하여 연소로의 온도와 산소공급량에 따라 다양한 화재조건에서 연기입자를 균일하게 발생시키고, 정전저압 임팩터를 사용하여 연기입자의 크기에 따른 개수농도를 실시간으로 측정하였다. 실험 결과 4가지 플라스틱의 연기입자 크기분포 특성은 여러 측면에서 PP와 유사하며 목재와는 확연히 다르게 나타났다.

• Journal of Korean Society for Atmospheric Environment
• /
• 제22권E2호
• /
• pp.78-88
• /
• 2006

In order to study the characteristics of cloud, a real-scale experiment for cloud generation was carried out using an extinct vertical mine (430 m height) located in the northeastern Honshu, Japan. The dry particles generated from the three-step concentrations of NaCl solutions were used for cloud generation. The number size distributions of initial dry particles and cloud droplets were monitored by Scanning Mobility Particle Sizer (SMPS) and Forward Scattering Spectrometer Probe (FSSP) at bottom and upper sites of pit, respectively. The polymeric water absorbent film (PWAF) method was employed to measure liquid water content ($W_L$) as a function of droplet size. Moreover the chemical properties of individual droplet replicas were determined by micro-PIXE. The CCN number concentration shows the lognormal form in dependence of the particle size, while the number size distributions of droplets are bimodal showing the peaks around $9{\mu}m$ and $20{\mu}m$ for every case. In comparison to background mineral particles, right shifting of size distribution line for NaCl particles was occurred. When NaCl solutions with three-step different concentrations were neulized, $W_L$ shows the strong droplet size dependence. It varied from $10.0mg\;m^{-3}$ up to $13.6mg\;m^{-3}$ with average $11.6mg\;m^{-3}$. A good relationship between $W_L$ and cloud droplet number concentration was obtained. Both chemical inhomogeneities (mixed components with mineral and C1) and homogeneities (only mineral components or C1) in individual droplet replicas were obviously observed from micro-PIXE elemental images.

• Bulletin of the Korean Chemical Society
• /
• 제24권8호
• /
• pp.1172-1176
• /
• 2003

This study aims to investigate the applicability of Sd/StFFF and to develop a method for size characterization of urban airborne particles, focusing primarily on particles larger than about 1 mm. It was found that the airborne concentration vary with time, although no particular seasonal trend was observed. When averaged over time, the airborne concentration was the lowest in the park areas with 99 ㎍/m³. The apartment, industrial, and central city area showed similar levels of the airborne concentrations with 166, 170, and 171 ㎍/m³, respectively. The housing area showed the highest airborne concentration with 201 μg/m³ among all tested areas. A power-programmed Sd/StFFF was used for size analysis of airborne particles with the initial field strength of 300 rpm, $t_a$ = 4, $t_i$ = -16, p = 8, and the flow rate of 7 mL/min. It was found that urban airborne samples were mostly populated by particles having diameters between about 5 to 20 ㎛, although all have broad size distributions ranging up to about 50 ㎛. Under the Sd/StFFF condition used in this study, no significant differences were found in size distributions among the airborne particles collected at different urban sites, and also among those collected at different times.

• Elastomers and Composites
• /
• 제55권2호
• /
• pp.108-113
• /
• 2020

Wear particles of the model tread compounds for bus and truck tires were made using a laboratory abrasion tester and characterized based on their size distributions, shapes, and crosslink densities. The influence of the carbon black contents and rubber compositions (NR= 100 and NR/BR= 80/20) on the production of wear particles was investigated. The wear particles were separated according to size using a sieve shaker. The shape properties of the wear particles were analyzed using an image analyzer and scanning electron microscopy (SEM). Their shapes were observed as tiny stick cookies or sausages with bumpy surfaces. The particle size distribution tended to be smaller with increasing carbon black content. Moreover, the particle size distributions of the NR = 100 samples were larger than that of the NR/BR blend samples. There were different filaments in the wear particles. The filament diameters tended to be thinner with increasing carbon black content. The crosslink density increased with increasing carbon black content, and the crosslink densities of the NR= 100 samples were lower than those of the NR/BR blend ones. The particle size distribution tended to be smaller with increasing crosslink density. Based on the experimental results, the wear particles can be produced by detaching debris from the main body through repetitive strain and recovery.

• 응용통계연구
• /
• 제11권2호
• /
• pp.269-285
• /
• 1998

임상시험연구의 설계에서 적절한 표본수의 결정은 매우 중요한 문제 중의 하나이다. 본 논문에서는 생존분포를 비교하기 위한 여러 가지 방법들을 소개하고, 각 방법에서의 가정들을 고찰하였다. 또한 다양한 상황에서의 표본수와 검정력 등을 비교제시하고 모의실험을 통해 각 방법들의 이론상의 검정력과 실제 검정력을 알아보았다 그 결과로서 의학연구자들이 처한 여러 상황에 적합한 표본수의 결정방법을 제시하였다.