• 한국표면공학회지
• /
• 제46권4호
• /
• pp.175-180
• /
• 2013

Carbon nanofilaments (CNFs) could be synthesized using $C_2H_2/H_2$ as source gases and $SF_6$ as an incorporated additive gas under thermal chemical vapor deposition system. Ni powders were used as the catalyst for the formation of the CNFs. During the initial deposition stage, the initiation of the CNFs on the Ni catalyst was investigated. The geometries of the as-grown CNFs on Ni catalyst were strongly dependent on the size and/or the shape of Ni catalyst. Small size catalyst (<150 nm in diameter) gives rise to the unidirectional growth of the CNFs. On the other hand, large size catalyst (150~500 nm), the bidirectional growth of the CNFs could be observed. Particularly, the well faceted parallelogram-shaped Ni catalyst could give rise to the bidirectional growth of the CNFs having the symmetrically opposite direction. Eventually, these bidirectional growths of CNFs were understood to form the well-developed carbon microcoils (CMCs). Based on these results, the optimal shape and the size of the Ni catalyst to form the CMCs were discussed.

• 한국막학회:학술대회논문집
• /
• 한국막학회 1996년도 춘계 총회 및 학술발표회
• /
• pp.55-56
• /
• 1996

Heterophase polymer system has been attractive for a potential applicability to gas separation membrane material. It has been known that there is a trade-off between gas permeability and its selectivity in common polymers. Therefore, the heterophase polymer can be an alternative for a gas separation membrane material because its transport properties can be readily controlled by blending of two different polymers. The transport properties of immiscible polymer blends strongly depend upon the intrinsic transport properties of corresponding polymers. Another important factor to determine the transport properties is their morphology: volume fraction, size and shape of dispersed phase. Although the effect of the volume fraction of the dispersed phase on the transport properties has been widely investigated, the size and shape effects have been paid attention very much. In an immiscible polymer blend of two polymers, its morphology is primarily controlled by its volume fraction of dispersed phase. Therefore, the effect of the size of the dispersed phase can be hardly seen. Therefore, a block copolymer has been commonly employed to control their morphology when each block is miscible with one or the other phase. In this work, gas transport properties will be measured by varying the morphology of the heterophase polymer membrane. The transport properties will be interpreted in terms of their morphology. The effect of the volume fraction of the PI phase and, in particular, its size effect will be investigated experimentally and theoretically.

• Structural Engineering and Mechanics
• /
• 제35권3호
• /
• pp.335-348
• /
• 2010

Cutouts are often provided in structural and aircraft components for ventilation, for access, inspection, electric lines and fuel lines or sometimes to lighten the structure. This paper addresses the effects of cutout shape (i.e., circular, square, diamond, elliptical-vertical and elliptical-horizontal) and size on buckling and postbuckling response of quasi-isotropic (i.e., $(+45/-45/0/90)_{2s}$) composite laminate under uni-axial compression. The finite element method is used to carry out the investigation. The formulation is based on first order shear deformation theory and von Karman's assumptions are used to incorporate geometric nonlinearity. The 3-D Tsai-Hill criterion is used to predict the failure of a lamina while the onset of delamination is predicted by the interlaminar failure criterion. It is observed that for the smaller size cutout area there is no significant effect of cutout shape on load-deflection response of the laminate. It is also concluded that the cutout size has substantial influence on the buckling and postbuckling response of the laminate with elliptical-horizontal cutout, while this effect is observed to be the least in case of laminate with elliptical-vertical cutout.

• 열처리공학회지
• /
• 제17권6호
• /
• pp.342-345
• /
• 2004

In this work, a new method of measuring volume fraction of deformation-induced ${\varepsilon}$ martensite is proposed using endothermic heat on reverse transformation. As grain size increases, the amount of ${\varepsilon}$ martensite forming on cooling increases. However, with a decrease in grain size, more ${\varepsilon}$ is induced by deformation, improving shape memory effect.

• 한국해양공학회지
• /
• 제22권6호
• /
• pp.7-12
• /
• 2008

The present study numerically investigates the effect of the shape of absorbing revetment on wave overtopping rate under regular and irregular incident waves. At first, the numerical model developed by Hur and Choi(2008), which considers the flow through a porous medium with inertial, laminar and turbulent resistance terms, directly simulates Wave-Structure-Sandy seabed interaction and can determine the eddy viscosity with LES turbulent model in 2-Dimensional wave field (LES-WASS-2D), is validated when compared to experimental data. Numerical simulations are then performed to examine the effect of the shape of absorbing revetment and incident wave conditions on wave overtopping rate. The numerical result shows that the wave overtopping rate decreases with the slope gradient of absorbing revetment under both regular and irregular waves. In addition, the effects of mean grain size and porosity of absorbing revetment, incident wave period and crest height on wave overtopping rate are discussed.

• 대한인간공학회지
• /
• 제28권4호
• /
• pp.61-69
• /
• 2009

With increasing needs for affective design, it became an essential part in a product development process to look up quantitative ergonomic data that reflects customers' preferences on design factors in various products. This study looked at wide LCD monitors and analyzed customers' affective preferences regarding monitor's bezel frame size and shape. The monitor's bezel frame depth, size and ratio were selected as independent variables among many design parameters. As dependent variables, customer's subjective preferences were measured. A statistical analysis revealed that monitor's bezel frame depth, size and ratio had significant effects on customer's preferences. Also, it was possible to find a different tendency on affective variables and their levels for 19" and 24" wide LCD monitors. In general, experiments revealed that customers reacted more sensitively in 24" wide LCD monitors to all variables. In 19" wide LCD monitors, only the lower frame bezel size had a significant effect, otherwise, lower, upper and side frame bezels appeared to be effective variables in 24" monitors. In order to reflect customer's affective preferences to new design of wide LCD monitors, this study is expected to provide quantitative ergonomic data and guidelines for the design of wide LCD monitor's bezel frame depth and size.

• 한국가스학회지
• /
• 제19권5호
• /
• pp.20-28
• /
• 2015

탄화수소 선택적 촉매환원공정에서 ${\gamma}$-알루미나에 지지된 금속 산화물 촉매의 크기 및 형태에 따른 질소산화물 ($NO_x$) 저감 특성에 대해 조사하였다. 환원촉매로는 Ag, Cu 및 Ru를 사용하였으며, n-heptane을 환원제로 사용하였다. Ag/${\gamma}$-$Al_2O_3$ 촉매의 경우 온도범위 $250{\sim}400^{\circ}C$에서 20 nm>50 nm>80 nm 순으로 Ag의 크기가 작을수록 $NO_x$ 전환효율이 높게 나타났다. 금속 산화물 촉매의 형태에 따른 영향은 구형과 선형에 대해 살펴보았다. Ag와 Cu는 동일한 조건에서 선형이 구형보다 $NO_x$ 전환효율이 높은 것으로 나타났으나, Ru의 경우에는 형태에 따른 영향이 거의 관찰되지 않았다. 사용된 금속산화물 촉매 중에서 Ag를 사용했을 때 $NO_x$ 저감효율이 가장 높았으며, 선형의 Ag를 사용했을 때 $300^{\circ}C$의 반응온도에서 대부분의 $NO_x$를 제거할 수 있었다. Cu와 Ru 촉매상에서는 NO가 환원되기보다는 $NO_2$로의 산화반응이 우세하여 전체적으로 $NO_x$ 저감효율이 낮게 나타났다.

• 한국분말재료학회지
• /
• 제9권4호
• /
• pp.251-260
• /
• 2002

In the viscosity measurement of PIM feedstock, slip correction methods require a number of experiments and produce a high level of error. In this study, a rotational rheometer with a parallel-discs configuration having different surface roughness was tried to minimize the effect of the slip phenomenon. Disc surface was prepared in 3 different roughness conditions - a smooth and 2 roughened surfaces. Results with the roughened surfaces were compared with the results obtained with a slip correction method. Relationship between powder characteristics such as size and shape and a surface roughness of the disc was examined for feedstock of 4 different powders with a same binder. As results, the effect of the slip phenomenon could be sufficiently minimized on the roughened surface in most cases. However, the effect of the slip phenomenon could not be sufficiently minimized for feedstock of a round-particular-shape powder and in the case of very narrow gap size.

• 한국분말재료학회지
• /
• 제9권2호
• /
• pp.96-102
• /
• 2002

In the present study, equiatomic porous TiNi shape-memory alloys have been successfully prepared by self-propagating high-temperature synthesis (SHS) using elemental titanium and nickel powders. The porous TiNi alloys thus obtained have an open porous structure with about 64 vol.% porosity, and the pore size is about 1.8 mm. The effect of preheating temperature on the microstructure have been investigated. It is found that the pore size increases with increasing preheating temperature. Moreover, the preheating temperature was shown to have a significant effect on the microstructrue of the SHS-synthesized porous TiNi shape memory alloys.

• Computers and Concrete
• /
• 제17권1호
• /
• pp.107-127
• /
• 2016

Concrete is a heterogeneous material containing many weaknesses such as micro-cracks, pores and grain boundaries. The crack growth mechanism and failure behavior of concrete structures depend on the plastic deformation created by these weaknesses. In this article the non-linear finite element method is used to analyze the effect of presence of micro pore near a crack tip on both of the characteristics of crack tip plastic zone (its shape and size) and crack growth properties (such as crack growth length and crack initiation angle) under pure shear loading. The FE Code Franc2D/L is used to carry out these objectives. The effects of the crack-pore configurations and the spacing between micro pore and pre-excising crack tip on the characteristics of crack tip plastic zone and crack growth properties is highlighted. Based on the obtained results, the relative distance between the crack tip and the micro pore affects in very significant way the shape and the size of the crack tip plastic zone. Furthermore, crack growth length and crack initiation angle are mostly influenced by size and shape of plastic zone ahead of crack tip. Also the effects of pore decrease on the crack tip by variation of pore situation from linear to perpendicular configuration. The critical position for a micro pore is in front of the crack tip.