• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.250-253
• /
• 2001

This paper is proposed a sinusoidal input voltage Multi-level AC-DC Converter using transformer. In this paper Multi-level PWM Control converter which controls input current by combining buck Converters together to improve input current characteristic, and confirmed its validity throughout simulation and experiment. This method, which is multiplying and duplicating output of converter of equal capacity, is able to control unit power factor of input current, reduce the problem caused by high frequency switching, and apply to high power converter because filter is not necessary.

• Proceedings of the KIEE Conference
• /
• 1998.07f
• /
• pp.2121-2123
• /
• 1998

In recent years, A PWM Converter or Switched Mode Converter with high power factor and sinusoidal input current have got widespread studied. But, Almost all of studies is based on linear load. This paper reports on research aimed at achieving high power factor and sinusoidal input current waveform for electronic arc welder, which has nonlinear dynamic characteristics. It is shown that simulation result yield its property.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.5
• /
• pp.851-858
• /
• 2017

In this study, the voltage control system of a single phase full bridge inverter was designed based on the SPWM driving method. The voltage control system consists of a single-phase full-bridge inverter, a PI controller for linearly compensating the error between the reference voltage and the output voltage, a PWM driving circuit for generating the gate signal using the SPWM method from the controller signal, and an LC filter for filtering the inverter output voltage waveform into sinusoidal waveform. Finally, the voltage control system of a single-phase full-bridge inverter based on the PWM driving method was modeled using EMTP-RV and by showing that the output voltage accurately converges the reference voltage through several simulation examples, the validity of the control system design was verified.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.535-538
• /
• 1994

In this paper, an isolated ZVS-PWM boost converter is proposed for single stage line conversion. For power factor correction, we used the half bridge topology at the primary side of isolation transformer permitting switching devices to operate under ZVS by using circuit parastics and operating at a fixed duty ratio near 50%. Thus the relatively continuous input current distortion and small size input filter are also achievable. The ZVS-PWM boost operation of the proposed converter can be achieved by using the boost inductor $L_f$, main switch $Q_3$, and simple auxiliary circuit at the secondary side of isolation transformer. The secondary side circuit differ from a conventional PWM boost converter by introduction a simple auxiliary circuit. The auxiliary circuit is actived only during a short switching transition time to create the ZVS condition for the main switch as that of the ZVT-PWM boost converter. With a single stage, it is possible to achieve a sinusoidal line current at unity power factor as well as the isolated 48V DC output. Comparing to the two stage schemes, overall effiency of the proposed converter is highly improved due to the effective ZVS of all devices as well as single stage power conversion. Thus, it can be operated at high switching frequency allowing use of small size input filter. Minimum voltage and current stress make it high power application possible.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.16 no.6
• /
• pp.594-601
• /
• 2011

In this paper, a new current controller with the compensation of an unbalance and distorted grid voltages has been proposed. Generally, in the three-phase power system, single phase or nonlinear loads can be connected with the 3 phase linear load simultaneously on the same point of common coupling. Therefore, The source voltage unbalance and distortion problem can be occurred. Under these unbalance and distorted grid voltage conditions, the input current of 3 phase PWM rectifiers also have unbalance and distortion. In this paper, a current controller with the simple Model Reference Adaptive System based unbalance and distorted voltages observer is proposed to get a sinusoidal input current. The performance of the proposed algorithm is verified through the simulation and the experiment.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.295-300
• /
• 1990

This paper describes a new method to increase the fundamental output of PWM inverter by adding all triplen-harmonics to sinusoidal reference wave. As a result, the amplitude of the fundamental component is increased upto 21 percent compared with the conventional SPWM method, and hence the conversion efficiency of dc link is higher. Also as the commutation number of the inverter is decreased to two-thirds, the heating of the switch devices is reduced. In addition random carrier modulation is adopted to lower the acoustic noise at given frequency modulation index.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.340-343
• /
• 1990

Recently, Power Electronics system increase makes harmonics and low input power factor problem. In this paper present new analysis method of PWM Boost AC/DC Converter. This PWM AC/DC Converter is capability of unity power factor, control of DC side voltage level, generation, and near sinusoidal current in 3-phase line. The control of this type of converter is widely discussed. And this paper propose new phase convert function and analysis in steady state of system to obtain amplitude and phaser of switching function. This switching function is general solution and it can use in high power approach. And this control method show the clear meaning of control variable. This paper propose new analysis method of Boost AC/DC Converter of steady state and 3-phase 2KW experimental system show its validity.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.318-320
• /
• 1996

This paper describes a new dc/ac inverter system, which makes use of parallel loaded high frequency resonant inverter consisting of full bridge, for achieving sinusoidal ac waveform. Because current throughout switch at turn-on is always zero in proposed inverter, low stress and low switching loss is achieved. Operating characteristic of proposed system is analyzed in per unit system using computer simulation. Output voltage of it include low harmonics and almost close tn sine wave.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.13 no.3
• /
• pp.82-92
• /
• 1999

In this paper, we realize the active PFC(Power Factor Correction) system of the BF(Boost Forward) converter with the PWM-PFM control technique to control DC output voltage, to rermve the noise like hanronics at the output voltage, amd to control the input ClUTent with sinusoidal wave synchronized by the source voltage. We take the simulation and analyze the switching signal of the BF converter, input/output voltage and current, its harmonics and power factor through PSpice. And it has bren obtained harmonic reduction and efficiency improverrent.errent.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.645-648
• /
• 1991

In conventional sinusoidal wave PWM control, torque oscillation is a problem on account of harmonic component. This paper deals with the choice of line-to-line voltage modulation method, which is effective in using DC(direct current) source voltage and in controlling harmonic oscillation, and the pattern to reduce swiching loss through 1/3 pause of switching interral. So, this paper deals with valid realization of harmonic component and high torque response on variable load by simulation and experiments to compensate occurring problems when line-to-line modulation are applied to PWM inverter.