• 한국재료학회지
• /
• 제11권6호
• /
• pp.465-471
• /
• 2001

수용성 매체에서 젤-케스팅 공정을 이용하여 용융실리카를 기본으로 하는 다성분계 세라믹 코어 (中子)를 제조하고, 소결조건에 따른 제반 기계적 물성과 알칼리 부식용액에 의한 용출특성을 고찰하였다. 1000cP (at $50sec^{-1}$ ) 이하의 낮은 점도를 갖는 50vol%의 고농도 다성분계 세라믹 슬림의 제조가 가능하였다. 성형체는 안정화시킨 슬림을 몰드에 부어 상온에서 겔화시킨 후 $25^{\circ}C$, 80% 상대습도 분위기 하에서 48시간동안 건조시켜 제조하였으며 건조된 성형체에는 균열이 발생하지 않았다. 세라믹 코어 성형체의 소결온도가 상승할 수록 상온강도, 겉보기 밀도, 수축률은 시편의 기공도와 역비례하여 증가하였다. 세라믹 코어 소결체의 용출속도는 동일한 온도에서 알칼리 부식용액의 농도에 의존하였으며, 소결체의 기공도가 클수록 증가하였다.

• Journal of Magnetics
• /
• 제13권3호
• /
• pp.110-113
• /
• 2008

In this study, heavy rare earth garnet $Tb_2Bi_1Ga_1Fe_4O_{12}$ powders were fabricated by a sol-gel and vacuum annealing process. The crystal structure was found to be single-phase garnet with a space group of Ia3d. The lattice constant $a_0$ was determined to be 12.465 ${\AA}$. From the analysis of the vibrating sample magnetometer (VSM) hysteresis loop at room temperature, the saturation magnetization and coercivity of the sample are 7.64 emu/g and 229 Oe, respectively. The N$\acute{e}$el temperature($T_N$) was determined to be 525 K. The M$\ddot{o}$ssbauer spectrum of $Tb_2Bi_1Ga_1Fe_4O_{12}$ at room temperature consists of 2 sets of 6 Lorentzians, which is the pattern of single-phase garnet. From the results of the M$\ddot{o}$ssbauer spectrum at room temperature, the absorption area ratios of Fe ions on 24d and 16a sites are 74.7% and 25.3%(approximately 3:1), respectively. These results show that all of the non-magnetic Ga atoms occupy the 16a site by a vacuum annealing process. Absorption area ratios of Fe ions are dependent not only on a sintering condition but also on the temperature of the sample. It can then be interpreted that the Ga ion distribution is dependent on the temperature of the sample. The M$\ddot{o}$ssbauer measurement was carried out in order to investigate the atomic migration in $Tb_2Bi_1Ga_1Fe_4O_{12}$.

• 한국세라믹학회지
• /
• 제30권4호
• /
• pp.299-308
• /
• 1993

Dispersant was used to avoid the agglomeration of aluminum hydrate precipitate and improve the sinterability of calcined alumina powder. The mean particle size of the aluminum hydrate precipitates was 0.26${\mu}{\textrm}{m}$ and 0.44${\mu}{\textrm}{m}$ when ball-milled with and without dispersant, respectively. After calcination at 110$0^{\circ}C$ for 5 hours, the size of the alumina powder without dispersant increased to 0.84${\mu}{\textrm}{m}$, while with dispersant slightly decreased to 0.22${\mu}{\textrm}{m}$. The most thermally active alumina powder was obtained from the sample calcined at 110$0^{\circ}C$ for 5 hours with the 1% dispersant concentration. Using the calcined alumina powder at the above optimized condition, the specimen showed fired density of 3.94g/㎤, 4-point MOR of 364MPa, and KIC of 3.26MPam1/2 after sintered at 155$0^{\circ}C$ for 3 hours.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1660-1662
• /
• 1996

Superconducting current lead is one of the promising applications of the oxide high-Tc superconductors, because they have the advantage of decreasing heat conduction to low temperature region, comparing with a conventional cooper alloy lead. High critical current density is a key factor for the applications such as current lead. $(Bi,Pb)_{2}Sr_{2}Ca_{2}Cu_{3}O_{x}$ high Tc superconductor hase been investigated in terms of critical current density. Bi-2223 superconducting current lead made by CIP and solid state sintering process. Bi-2223 current lead that heat treated at $836\;^{\circ}C$ for 240 h in 1/13 $PO_2$ had over $500\;A/cm^2$ of critical current density at 77K. We knew that the superconducting properties of tube type current leads were better than rods type of them. And we investigated the relation of Bi-2223 formation and heat treatment condition by XRD and SEM analysis.

• 한국표면공학회지
• /
• 제50권6호
• /
• pp.465-472
• /
• 2017

The ingot fabrication conditions related with the thermal shock bearing phase and microstructure have investigated for the rare earth zirconate ceramic material, lanthanum gadolinium zirconate, as a thermal barrier coating using electron beam evaporation method. The thermal shock resistance of the prepared ingot was evaluated by high energy electron beam irradiation. The rare earth zirconate ceramic powder was prepared by controlling the raw material powder composition of $La_2O_3$, $Gd_2O_3$ and $ZrO_2$ so as to have a composition of $(La_{0.3}Gd_{0.7})_2Zr_2O_7$ which was selected from the former study. Ingot samples were prepared under two conditions. The first condition is prepared by sintering the prepared powder mixture to form an ingot. The second condition is prepared by calcining the prepared powder mixture to form a composite phase and then sintering to form an ingot. X-ray diffraction(XRD) and Scanning Electron Microscope(SEM) were used to analyze phase forming behavior and microstructure of ingot samples. Nanoindentation method used to obtain elastic modulus and hardness of each ingot specimen. Also the stress distribution of ingot was simulated by using FEM method assuming the ingot surface was exposed to electron beam. As a results, in the case of an ingot having a network-shaped microstructure in which relatively coarse pores are included, it seems that the thermal shock resistance was higher than in the case of an ingot having a microstructure composed of relatively fine grains only or particles with the similar level size when the high energy electron beam irradiation.

• 한국세라믹학회지
• /
• 제41권9호
• /
• pp.715-721
• /
• 2004

합성 수산화아파타이트(HAp)와 바인더로서 젤라틴(GEL)을 사용하여 공침법으로 조성비가 서로 다른 HAp/GEL 균질복 합체 4종을 제조하였고, 이 균질복합체를 냉간정수압법으로 성형한 후 공기중에서 여러조건으로 소결하였다. HAp/GEL composite의 소결체는 XRD 및 FT-IR로 결정성 및 구조를 조사하였고, 또한 소결시편은 만능재료시험기(UTM)로 압축강도를 측정하였으며, 파단된 소결시편의 표면은 SEM으로 관찰하였다 HAp/GEL composite는 120$0^{\circ}C$에서 3시간 소결하였을 경우 부분적인 $\alpha$, $\beta$-tricalcium phosphate로 상전이가 일어났다. 소결체의 기공률은 1.2-30.2% 범위였고, 소결시편의 압축강도는 16.2-60.1㎫ 범위의 값을 나타냄으로써 기공율에 비해 높은 강도를 나타내었다.

• 전기화학회지
• /
• 제9권3호
• /
• pp.124-131
• /
• 2006

기존의 용융탄산염 연료전지용 연료극인 Ni-Cr전극은 제조과정이 복잡하며, 운전조건에서 전극의 소결과 creep현상으로 인하여 전극의 기공률과 두께가 감소하는 문제점이 있어 상용화에 걸림돌이 되고 있다. 이에 본 연구에서는 Ni-Cr계 전극보다 creep저항성이 우수하다고 알려져 있는 Ni-Al계 합금을 사용하였다. 또한 공정의 단순화로 비용을 절감시키기 위해, 소성과정을 제외하고 tape casting과 건조과정을 거친 green sheet를 단위전지에 장착하여 전처리 과정 중에 소결시키는 in-situ 소결법에 대해 연구하였다. 그러나 기존의 전처리 방법을 이용한 단위전지 평가에서 Ni-Al 합금의 상분리 현상으로 인해 기대하였던 creep저항성 향상을 확인하지 못했고, 운전중 Ni-Al합금 연료극에 단위전지의 구성요소인 matrix 기공크기보다 작은 기공(${\leq}0.4{\mu}m$)이 다량 생성되어 전해질 재분배를 일으켜 성능이 하락하는 문제점이 나타났다. 따라서 이러한 문제점을 해결하고자 전처리 조건을 변화시키며 실험을 수행하였다. 그 결과, 비활성 기체인 질소를 일정한 구간에 사용함으로써 기존 전처리에서 발생하였던 Ni-Al 합금의 상분리 현상을 억제할 수 있었으며 이로 인해 creep저항성 또한 향상시킬 수 있었다. 그러나 운전 중 생성되는 matrix기공크기보다 작은 기공(${\leq}0.4{\mu}m$) 형성비율은 억제할 수 없었다. 위의 전처리 조건을 가지고 단위전지 운전실험을 하였고, 전해질 함침비율을 조절함에 따라 성능을 향상시킬 수 있었으며 2000시간 동안 일정하게 유지함을 확인하였다. 이로부터 기존의 소성전극과 비교하여 많은 장점을 가지고 있는 in-situ 소결법의 가능성을 확인할 수 있었다.

• 한국세라믹학회지
• /
• 제53권2호
• /
• pp.215-221
• /
• 2016

In this study, the utilization of the by-products of various industries was examined using raw materials of CSA high-functional cement such as coal bottom ash, red mud, phosphate gypsum, etc. Technology to improve energy efficiency and reduce $CO_2$ was developed as part of the manufacturing process; this technology included lower temperature sintering ($150{\sim}200^{\circ}C$) than is used in the OPC cement manufacturing process, replacement of CSA cement with the main raw material bauxite, and a determination of the optimum mix condition. In order to develop CSA cement, a manufacturing system was established in the Danyang plant of the HANIL Cement Co. Ltd., in Korea. About 4,200 tons of low purity expansion agent CSA cement (about 16%) and about 850 tons of the lime-based expansion agent dead burned lime (about 8%) were produced at a rate of 60 tons per hour at the HANIL Cement rotary kiln. To improve the OPC cement properties, samples of 10%, 13%, and 16% of CSA cement were mixed with the OPC cement and the compressive strength and length variation rate of the green cement were examined. When green cement was mixed with each ratio of CSA cement and OPC cement, the compressive strength was improved by about 30% and the expansibility of the green cement was also improved. When green cement was mixed with 16% of CSA cement, the compressive strength was excellent compared with that of OPC cement. Therefore, this study indicates the possibility of a practical use of low-cost CSA cement employing industrial wastes only.

• 한국세라믹학회지
• /
• 제35권2호
• /
• pp.172-179
• /
• 1998

Valve lifter namely tappet is supported by lifter hole which is located upper side of camshaft in cylinder block transforms rotatic mvement of camshaft into linear movement and helps to open and shut the en-gine valve as an engine parts. The face of valve lifter which is continuously contacting with camshaft brings about abnormal wears such as unfair wear and early wear because it is severely loaded in the valve train system. These wears act as a defect like over-clearance and cause imperfect combustion of fuel during the valve lifting in the combustion chamber. Consequently this imperfect combustion makes the engine out-put decrease and has cause on air pollution. To prevent these wears therefore The valve lifter cast in me-tal developed into SiC ceramics valve lifter which has an excellence in wear and impact resistance As a results the optimum process conditions like injection condition mixture ratio and debonding process could be established. After sintering fine-sinered dual microstructure in which prior ${\alpha}$-SiC matches well with new SiC(${\beta}$-SiC) produced by reaction among the ${\alpha}$-SiC carbon and silicon was obtained. Based on the study it is verified that mechanical properties of SiC valve lifter are excellent in Vickers hardness 1100-1200 bending strength (300-350 Pa) fracture toughness(1.5-1.7 Mpa$.$m1/2) Through engine dynamo test-ing SiC valve lifter and metal valve lifter are examined and compared into abnormal phenomena such as early fracture unfair and early wear. It is hoped that this research will serve as an important springboard for the future study of heavy duty diesel engine parts developed by ceramics which has a good wear resis-tance relaibility and lightability.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.1-9
• /
• 2020

국내 유도무기 분야의 비약적 발전에도 불구하고, 유도무기 내 정밀 기계 부품의 제조 방식은 80년대의 기계 절삭가공 및 정밀주조 방식에서 눈에 띄는 발전이 없는 상황이다. 생산 수량이 많지 않고 높은 신뢰도를 요구하는 만큼 기계 절삭가공이나 정밀주조 방식이 유리한 측면이 있는 것은 분명하다. 하지만 광범위 지역 제압용 유도무기(천무, 해룡 등)의 경우 유도탄 1기당 수백 개 이상의 자탄이 소요되어 대량 생산성을 요구하고 있으며, 각각의 부품 중 가공 난이도가 높은 경우는 기존의 기계 절삭가공 및 정밀주조 방식으로는 생산성과 품질을 동시에 충족시키기 어려운 실정이다. 특히 최근에 대두되고 있는 국내 방산제품들의 해외 시장 수출 경쟁력 강화를 위해서는, 생산성의 개선을 통한 원가 절감이 필수적이라고 할 수 있다. 본 연구에서는 상기에 언급된 문제의 해결을 위해 유도무기 소형 정밀부품의 MIM(Metal Injection Moulding) 공법 적용 가능성에 대해 연구한다. MIM 공법의 기초연구를 수행하여 공정 설계 간 최적의 공정 조건을 도출하였으며, 이를 적용하여 제작된 자탄신관 소형 정밀부품과 기존 방식으로 제작된 제품의 품질 검사 결과 비교 및 해당 부품이 적용되어 제작된 신관의 기능시험 수행 결과를 통해 MIM 공법의 적용 가능성을 소개한다.