• 한국세라믹학회지
• /
• 제40권6호
• /
• pp.553-559
• /
• 2003

PDP(Plasma Display Panel) rib은 고정세의 패턴 설계 및 복잡, 다양한 공정으로 제조되고 있다. Rib은 PDP제조 공정 및 역할상 매우 중요한 부분의 하나이며 rib의 소결 정도는 cross-talk와 같은 현상을 방지하는 데에 중요한 역할을 한다. 저렴하고 높은 양산성을 가진 rib은 주로 스크린 프린팅법에 의해 제작되지만, 인쇄, 소성 등 일련의 제조 공정을 거친 후 얻어진 수백 $\mu\textrm{m}$ 미세규격의 격벽 소결체의 소결도를 정확히 평가하기는 쉽지 않다. 본 연구에서는 rib의 소결도를 직접적 판단할 수 있는 방법에 대한 연구의 일환으로서 주로 소결 말기에 나타나는 기공의 응집, 성장을 potentiostat로 기공에서의 절연 파괴, 전계 집중의 원리를 이용함으로서 소결도를 측정했다 이 측정값은 각 온도에서 열처리한 시편에 대한 밀도값과 유사한 경향성이 나타남을 확인할 수 있었다 개기공, 폐기공의 분포에 따라 예상될 수 있는 측정오차는 온도에 따른 미세구조의 변화를 수차례의 전자 현미경 관찰을 통해 확인, 검증하여 미세규격 rib 소결도의 판단을 전기화학적 방법으로 예측 가능하다는 것을 알 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제11권1호
• /
• pp.18-25
• /
• 1998

G $d_{0.2}$C $e_{0.8}$ $O_{1.9}$(CGO) for electrolyte and L $a_{0.5}$S $r_{0.5}$Mn $O_3$(LSM50) for cathode in Solid Oxide Fuel Cells(SOFC) were synthesized by citrate process. Specimens were prepared with sintering temperatures at 110$0^{\circ}C$, 120$0^{\circ}C$ and 130$0^{\circ}C$, which were fabricated by slurry coating with citric acid contents. Interfacial resistance was measured between cathode and electrolyte using AC-impedance analyzer. With various citric acid content, the degree of agglomeration for the initial particles changed. Also sintering temperature changed the particle size and the degree of densification of cathode. Factors affecting the interfacial resistance were adherent degree of the electrolyte and cathode, distribution of TPB(three phase boundaries, TPB i.e., electrolyte/electrode/gas phase area) and porosity of cathode. By increasing the sintering temperature, particle size and densification of the cathode were increased. And then, TPB area which occurs catalytic reaction was reduced and so interfacial resistance was increased.sed.sed.d.

• 한국분말재료학회지
• /
• 제7권4호
• /
• pp.218-227
• /
• 2000

It is well known that the Cu-Cr alloys are very difficult to be made by conventional sintering methods. This difficulty originates both from limited solubility of Cr in the Cu matrix and from limited sintering temperature due to high vapor pressures of Cr and Cu components at the high temperature. Densification of Cu-50%Cr Powder compacts by conventional Powder metallurgy Process has been studied. Three kinds of sintering methods were tested in order to obtain high-density sintered compacts. Completely densified Cu-Cr compacts could be obtained neither by solid state sintering method nor by liquid phase sintering method. Both low degree of shrinkage and evolution of large pores in the Cu matrix during the solid state sintering are attributed to the anchoring effect of large Cr particles, which inhibits homogeneous densification of Cu matrix and induces pore generation in the Cu matrix. In addition, the effect of undiffusible gas coming from the reduction of Cu-oxide and Cr-oxide was observed during liquid phase sintering. A two-step sintering method, solid state sintering followed by liquid phase sintering, was proved to have beneficial effect on the fabrication of high-dendsity Cu-Cr sintered compacts. The sintered compacts have properties similar to those of commercial products.

• The Korean Journal of Ceramics
• /
• 제5권3호
• /
• pp.235-238
• /
• 1999

In a ceramic green body, some degree of nonuniformity in density always presents. These differences in green density will appear as nonuniform shrinkage after sintering takes place. For the complex ceramic bodies with various curves and angles, therefore, it is quite difficult to foresee the final dimensions precisely after sintering. This simulation study shows that, considering the sintering process as a thermal shrinkage phenomenon, the use of NASTRAN enables to predict the precise shape of a sintered body. Based on this result, 'the reverse engineering technique' has been developed that can unfold the exact dimensions of a green body to have the desired shape after sintering. This approach will provide a simple and useful tool for ceramic engineers to fabricate complicate bodies with tight dimensional tolerances.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권2호
• /
• pp.158-164
• /
• 1995

Solid solutions Sr$_{2}$(Ta$_{1-x}$ Nb$_{x}$)$_{2}$O$_{7}$, (x=0.0-1.0), composed of strontium tantalate(Tc=-107.deg. C) and strontium-niobate(Tc=1342.deg. C) were prepared by the conventional mixed oxide method and the flux method(molten salt synthesis method). Phase relation, sintering temperature, grain-orientation and dielectric properties for sintered ceramic samples were investigated with different compositions. Both Curie temperature and dielectric constant at Curie temperature were increased, and sintering behavior and the degree of grain-orientation were improved with the increase of Nb content. The single phase Sr$_{2}$(Ta/sib 1-x/Nb$_{x}$)$_{2}$O$_{7}$ powder was synthesized by using the flux method at lower temperatures, and sintering temperature was also reduced by using the flux method-derived powder than using the mixed oxide-derived powder. Sintering characteristics and dielectric properties of the specimens prepared by the flux method were better than those derived through the conventional mixed oxide method.thod.hod.

• 한국세라믹학회지
• /
• 제23권1호
• /
• pp.13-20
• /
• 1986

Zirconia soild electrolytes containing 4~10mol% of yttria were prepared by wet-blending of oxides and rea-ction-sintering, Sinterbility and degree of stabilization were optimized for the development of oxygen sensor. Fracture strength thermal expansion coefficient electrical conductivity and galvanic potential were measured and discussed with respect to the amount of ytria addition phase transformation microstructure and degree of stabilization. It was found that sintering and stabilization occurred when the composition was designed to be near the boundary region of $ZrO_2-Y_2O_3$ binary system. In such away a good zirconia solid electrolyte suitable for oxygen sensor could be developed.

• 한국세라믹학회지
• /
• 제35권8호
• /
• pp.836-842
• /
• 1998

In this experiment well-know additives for Mn-Zn ferrites CaO and {{{{ { SiO}_{2 } }} were added at various content and their effects on microstructures and magnetic properties with sintering atmosphere were examined. By adding up to 0.04wt% {{{{ { SiO}_{2 } }} and and 0.06wt% CaO the sintered density was increased and then decreased gra-dually. Higher sintered density and initial permeability were observed by adding both CaO and {{{{ { SiO}_{2 } }} than by adding CaO or {{{{ { SiO}_{2 } }} alone. Without any additives initial permeability and tan$\delta$/${\mu}$ decreased at 1000kHz as oxidation degree(${\gamma}$) increased.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.327-328
• /
• 2006

We have demonstrated that textured $Al_2O_3-mullite-SiC$ nanocomposites can be fabricated by slip casting followed by partial oxidation - reaction sintering of mixed suspensions of $Al_2O_3$ and SiC powders in a high magnetic field. The sintered density was changed by the degree of oxidation at 1200C and 1300C. The degree of orientation of alumina in the nanocomposite was examined on the basis of the X-ray diffraction patterns and scanning electron micrographs. It is confirmed that alumina-oriented nanocomposites were fabricated. The three-point bending strength at room temperature was observed for the nanocomposites.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.455-456
• /
• 2006

We have demonstrated that textured $Al_2O_3-mullite-SiC$ nanocomposites can be fabricated by slip casting followed by partial oxidation. reaction sintering of mixed suspensions of $Al_2O_3$ and SiC powders in a high magnetic field. The sintered density was changed by the degree of oxidation at 1200C and 1300C. The degree of orientation of alumina in the nanocomposite was examined on the basis of the X-ray diffraction patterns and scanning electron micrographs. It is confirmed that aluminaoriented nanocomposites were fabricated. The three-point bending strength at room temperature was observed for the nanocomposites.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.402-405
• /
• 2001

The BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics were prepared by conventional mixed oxide method. The structural and dielectric properties of the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics with the sintering temperature were investigated. Increasing the sintering temperature, the 2$\theta$ value of BaTiO$_3$peaks were shifted to the higher degree and intensity of the BaTiO$_3$and BaNbO$_3$peaks were increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 135$0^{\circ}C$ and 1375$^{\circ}C$, the grain was fine and uniform. Increasing the sintering temperature, the pore was decreased and the dielectric constant was increased. In the BaTiO$_3$+10wt%Nb$_2$O$_{5}$ ceramics sintered at 1375$^{\circ}C$, the dielectric constant and dielectric loss were 5424, 0.02 respectively.ctively.