• Journal of Power System Engineering
• /
• v.19 no.1
• /
• pp.45-49
• /
• 2015

This study focuses on the crack-healing behavior and bending strength of SiC ceramics with sintering additives of $SiO_2$colloid. Optimized crack-healing condition was found to be 1hr at an atmosphere of 1373 K. The maximum crack size that can be healed at the optimized condition was a semi-elliptical surface crack of $450{\mu}m$ in diameter. After heat treatment at the optimum temperature in air, the crack morphology almost entirely disappeared and the strength recovered to the value of the smooth specimens at room temperature for the investigated crack sizes up to $450{\mu}m$. The crack with width $1.4{\mu}m$ can be completely heal the surface crack.

• Journal of the Korea Safety Management & Science
• /
• v.2 no.3
• /
• pp.197-210
• /
• 2000

In this paper, sensor ring for antilock brake system was studied using the 400 series ferrite stainless steel powder. Because of more excellent corrosion resistance and mechanical characteristics than iron, sensor ring has been manufactured by P/M(Powder Metallurgy) method 400 series ferrite stainless steel. the results are following. 1, Compared with sensor ring made by iron, 400 series ferrite stainless steel has shown a good corrosion resistance without an addition surface treatment. thus the decreasing production process has been obtained. 2. The products before sintering are much more corrodible in the condition of spray test of salt water and ammonia than humidity and nitrogen condition.

• Journal of the Korea Safety Management & Science
• /
• v.5 no.1
• /
• pp.129-141
• /
• 2003

In this thesis, using the 400 series ferrite stainless steel such as 434LD$_2$ which are furter excellent then the existing ferric products in mechanical characteristics, and experiment has been conducted on corrosion resistance of sensor ring. The results are following. 1. The products before sintering are much more corrodible in the condition of spray test of salt water and ammonia than humidity and nitrogen condition. 2. 434LD$_2$ ferrite stainless steel has shown a good corrosion resistance without an addition surface treatment. thus the decreasing production process has been obtained. 3. As hardness value of $H_{RB}$ 80 and tensile test, 434LD$_2$ ferrite stainless steel with show a good endurance when it is combined to constant velocity joint (c/v joint), and has a good hardness properties endurable to sand and pebble impact.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.05a
• /
• pp.134-137
• /
• 2002

A new LTCC material in the $PbWO_4-TiO_2-B_2O_3-CuO$ system was developed. The developed material can be sintered at $850^{\circ}C$ and its dielectric properties are $\varepsilon_r=20-25, Q\timesf_o=30000~50000GHz$ , and $\tau_f=0.2~30ppm/^{\circ}C$, depending on the components moi ratio. Due to its low sintering temperature and microwave dielectric properties, the developed material can be used as a LTCC substrate for fabrication of multilayered microwave communication module set. In present study, using this material, tape casting condition was established. With this processing condition, a T-resonator was fabricated and its electrical properties were examined. Also, a 2-Pole band pass filter was fabricated and its frequency characteristics were compared with simulation results.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.737-743
• /
• 1998

The synthesis of $SrAI_2O_4:Eu^{2+}$ phosphor and its properties of both photoluminescence and long-phosphorescent were investigated as a function of sintering condition. Single phase of $SrAl_2O_4$ was obtained by sintering the mixtures of $SrCO_3$, $Eu_2O_3$, $AI_2O_34 and 3wt% $B_2O_3$ powders over 100$0^{\circ}C$ in Ar/H2 atmosphere. The optimum sintering condition for the long-phosphorescent phosphor of $SrAI_2O_4:Eu^{2+}$ was found at 130$0^{\circ}C$ for 3hours. The PL emission spectrum of $SrAI_2O_4:Eu^{2+}$ shows a maximum peak intensity at 520nm(2.384eV) with a broad emission extending from 450 to 650nm which resulted from the $4f^65d^1$$\rightarrow$$4f^7$ transition of $Eu^{+2}$ under 360nm exitation. Monitored at 520nm. the excita¬tion spectrum of $SrAI_2O_4:Eu^{2+}$ exhibits a maximum peak intensity at 360nm (3.44eV) with a broad absorption band extending from 250 to 480nm.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.40-43
• /
• 2000

Acicular $\alpha-FeOOH\; and\; Ba(OH)_2\cdot8H_2O$ are starting materials in this study. This paper presents the characteristics of the contents of citric acid and heating condition for preparing acicular barium ferrite powder. They control particle shape, crystalline phase, magnetic properties of acicular barium ferrite powder So the effects of the contents of citric acid and heating condition are studied. The experimental condition for starting materials were 800~1000$\circ C$ in firing and 0~40 wt% citric acid, respectively, Ba-ferrite particles fired at the range of 800 $\circ C$to 900 $\circ C$ were maintained as acicular particle shape, but there were mixed particles of acicular and round shape after fired at 950 $\circ C$. Ba-ferrite powder of the single phase was obtained in firing at 900~1000$\circ C$ and with 20 wt.% citric acid. There were unreacted phase of $\alpha-Fe_2O_3 \;and \; BaFe_2O_4$ phases as a second phase in case of sintering at below 850 $\circ C$. Acicular barium ferrite powder of single phase was also produced in firing at 900 $\circ C$ with 20 wt.% citric acid. The saturation magnetization of single phase of acicular $BaFe_12O_19$powder was about 51 emu/g and coercivity was about 4200 Oe.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1165-1166
• /
• 2006

An experiment was carried out to investigate the effect of Ba Stearate as a reducing agent on the magnetic and physical properties of anisotropic $BaFe_2-W$ type ferrite magnets. It was found that the magnetic properties of $BaO{\cdot}8.5Fe_2O_3$ were improved by adding 0.3 wt% of Ba Stearate, 0.5 wt% of $SiO_2$, and 0.5 wt% of CaO together. The optimum conditions for making magnets were as follows; semisintering condition: $1350^{\circ}C{\times}4.0$ h in nitrogen gas atmosphere, drying condition: $180^{\circ}C{\times}2.0$ h in air, sintering condition: $1160^{\circ}C{\times}1.5$ h in nitrogen gas atmosphere. Magnetic and physical properties of a typical sample were $J_m$ = 0.46 T, $J_r$ = 0.43 T, $H_{cJ}$ = 182.3 kA/m, $H_{cB}$ = 177.2 kA/m, $(BH)_{max}$ = 33.8 kJ/$m^3$, $T_C$ = $495^{\circ}C$ and $K_A$ = $2.65{\times}10^5\;J/m^3$ and $H_A$ = 1332 kA/m.

• Electrical & Electronic Materials
• /
• v.9 no.5
• /
• pp.455-462
• /
• 1996

Automobile Fuel Shortage Detecting Sensor, in this paper, was fabricated by using heat dissipation coefficient difference between gasoline and air condition the NTC thermistor of Mn-Ni Co system with the composition ratio of Mn$_{3}$O$_{4}$ : 9wt%, NiO : 28wt%, and CO$_{3}$O$_{4}$ : 61wt%. The condition of sensor operation is that, for turn-on characteristics, the time of arriving at 135mA must be less than 180 second when the DC voltage of 11V is applied in the air condition of -10.deg. C and that, for turn-off characteristics, the saturation current must be less than 60mA when the DC voltage of 15V is applied in the gasoline condition of 60.deg. C. It is known, from the experimental results, that the resistance range and B-constant for the Automobile Fuel Shortage Detecting Sensor with dimension of 5*3*0.9mm were 850-1150.ohm. and 1150-1250.deg. C, respectively and the resistance range and B-constant were agree with that of sensor operation condition. When Bi$_{2}$O$_{3}$ of 0-0.5wt% was added to Mn$_{3}$O$_{4}$ : 9wt%, NiO : 28wt%, and CO$_{3}$O$_{4}$ : 61wt% composition, the resistivity and B-value were 380-430(.ohm.-cm) and 1930 - 2030, respectively. Particularly, for Bi$_{3}$O$_{3}$ of 0.25-0.5wt%, the sintering density of over 90% and the operation characteristics necessary to Automobile Fuel Shortage Detecting Sensor were obtained. The difference of heat dissipation coefficient gasoline and air condition was 15 times.

• Journal of the Korean Ceramic Society
• /
• v.41 no.10 s.269
• /
• pp.783-787
• /
• 2004

Microwave dielectric properties and the microstructure of $Ba_5Nb_4O_{15}$ ceramics with $PbO-B_2O_3-SiO_2$ glass frit were investigated to reduce the sintering temperature of $Ba_5Nb_4O_{15}$ ceramics as a function of the amount of glass frit from $0.5wt\%$ to $10wt\%$ and the sintering condition. The sintered density and the microwave dielectric properties of $Ba_5Nb_4O_{15}$ ceramics were remarkably changed with the amount of glass fit which existed as a liquid phase and assisted the densification. $Ba_5Nb_4O_{15}$ with $3wt\%$ $PbO-B_2O_3-SiO_2$ glass frit sintered at $900^{\circ}C$ for 2 h showed dielectric constant (K) of 41.4, a quality factor (Q $\times$f) of 13,485 GHz, and a Temperature Coefficient of resonant Frequency (TCF) of 9 ppm/$^{\circ}C$. Due to no trace of physical and chemical reaction between this composition and Ag electrode cofired at $900^{\circ}C$ for 2 h, this ceramics can be a good candidate for the multilayer dielectric filter.

• Resources Recycling
• /
• v.20 no.1
• /
• pp.54-60
• /
• 2011

The spherical artificial aggregates (AAs) with a diameter of 8 mm, which contains fly ashes discharged from the fluidized bed combustion in a thermal power plant and clay were manufactured by direct sintering method at $1050{\sim}1250^{\circ}C$ for 10 minutes. The effect of fly ash contents on the bloating phenomenon in the AAs was analyzed. The AAs containing fly ash of the amount under 50 wt% showed the black-coring and bloating phenomena. The AAs containing fly ash of the amount over 5Owt%, however, the specific gravity was increased and the color of specimens fully changed to black. These color change phenomena were caused from the formation of FeO by the reduction reaction of almost $Fe_2O_3$ component by the excessive reducing atmosphere formed simultaneously with the rapid emission of the gases generated from the high contents of unburned carbon of with increasing the added fly ash amount. Specific gravity was decreased as fly ash contents increased in the case of sintering at the same temperature condition. Water absorption of all specimens except of the specimens containing 10 wt% fly ashes decreased with increasing sintering temperature. These were because a liquid phase was formed as the increasing the sintering temperature. In the case of the specimens manufactured in this study containing fly ashes discharged from the fluidized bed combustor in a the thermal power plant and 10~90 wt% of clay, the specific gravity was 0.9~1.8 and the water absorptivity was 8~60%, therefore it is considered that those results can be applied to the light or heavy aggregates.