• Electrical & Electronic Materials
• /
• v.7 no.1
• /
• pp.1-6
• /
• 1994

Cordierite based glass ceramics has become an electronic substrate material for electronic circuits and the use of whickers for improving strength and toughness is evident. Pure cordierite containing 15 vol.% silicon nitride were sintered by hot-prossing and it has above 99% density. Especially, it is assumed that toughening increasing at the more high sintering temperature relevants to the glass phase increasing, as showned in the roughness of the fracture surfaces. It was directionally dependent of whisker drirection during processing.

• Journal of Surface Science and Engineering
• /
• v.28 no.4
• /
• pp.243-254
• /
• 1995

The fabrication process of Cu-base anode for replacing Ni-base anode of molten carbonate fuel cell was investigated. Electrochemical performance and thermal stability of Cu-base anode were also investigated. Green sheet was prepared by mixing Cu and Ni powder with 1.5wt% methylcellulose and 100wt% water. The pore-size distribution of the Cu-base anode sintered at $800^{\circ}C$ for 30min showed almost uniform pore-size ranging from 4 to 20$\mu\textrm{m}$ and it was considered suitable for MCFC anode. Cu-Ni anode containing between 35 to 50wt% Ni exhibited current density of 111mA/$\textrm{cm}^2$ at 100mV overpotential and it was almost the some value for pure Ni anode. The sintering resistance of Cu-Ni increased with an increase of Ni addition. It was considered that the increase of sintering resistance was due to the decrease of diffusion rate of Cu and Ni with increasing the addition of Ni in Cu-Ni alloy.

• Journal of Surface Science and Engineering
• /
• v.29 no.6
• /
• pp.724-727
• /
• 1996

Electrolytic impregnation of nickel hydroxide into porous sintered nickel plaque from various nickel solutions were carried out at room or high temperatures and current density range of 2.5mA $cm^{-2}$ to 25mA $cm^{-2}$. The morphology of the deposited surface was observed with an electron microscope and the surface products were analyzed by means of X-ray diffraction method. Nickel hydroxide was deposited in nickel nitrate electrolyte, while deposits from sulphate or chloride solutions were almost metallic nickel. The loading level of nickel hydroxide from nitrate solutions was 1.6g$cm^{-3}$ void volume and the appearance of the surface was good quality. Discharge capacity of prepared electrodes in nickel nitrate electrolyte was larger than that of the others bath. It was considered that the cell capacity was dependent on the surface roughness of active material.

• Journal of Powder Materials
• /
• v.5 no.3
• /
• pp.210-219
• /
• 1998

The W-Cu composite powders were synthesized from W and Cu elemental powders by ball-milling process, and their microstructural changes and sintering behaviors were evaluated. The ball milling process was carried out in a 3-dimensional mixer (Turbula mixer) using zirconic ($ZrO_2$) ball and alumina ($Al_2O_3$) vial up to 300 hrs. The ball-milled W-Cu powders revealed nearly spherical shape. Microstructure of the composite powders showed onion-like structure which consists of W and Cu shells due to the moving characteristic of Turbula mixer. The W and Cu elements in the composite powders milled for 300 hrs were homogeneously distributed, and W grain size in the ball-milled powder was smaller than 0.5 $\mu\textrm{m}$. Fe impurity introduced during ball milling process was very low as of 0.001 wt%. The relative sintered density of ball-milled W-Cu specimens reached about 94% after sintering at $1100^{\circ}C$.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2002.02a
• /
• pp.187-194
• /
• 2002

This paper describes the experimental results on direct selective laser sintering of WC-Co mixture for rapid tooling. The experiments were carried out within an air, argon and nitrogen atmosphere. Coupons of single layer were sintered at various laser powers, scanning speeds and scan spacings. As the energy density (energy per unit scanned area) is increased, the thickness of coupons is increased. The main problem took place during sintering within an air atmosphere was severe oxidation of WC-Co mixture. As the laser power is increased and/or scanning speed is decreased, more severe oxidation occurred. Within an argon and nitrogen atmosphere the oxidation is reduced significantly. Experiments on multi-layer sintering were also carried out.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.4
• /
• pp.56-60
• /
• 2000

A new porous carbon material "woodceramics" was developed by carbonizing wood or woody materials impregnated with thermosetting resin. Steamed board and non-steamed board were made from thinned small log of Aomori Hiba (Thujopsis dolabrata S. et. Z. var. hondae M.). They were impregnated with phenol resin and sintered in a vacuum furnace at $650^{\circ}C$. In this paper, the manufacturing method of woodceramics and changes of dimension, weight and compressive strength were investigated. The changes of dimension, weight and compressive strength depend on the types of board and density.

• Journal of Powder Materials
• /
• v.4 no.3
• /
• pp.214-221
• /
• 1997

The densification and grain growth mechanisms of $UO_{2+x}$ in $H_2$ and in $CO_2$ have been investigated. Uranium dioxide powder compacts were sintered at 1$700^{\circ}C$ in $H_2$ or at 110$0^{\circ}C$ in $CO_2$ for various times from 0.5 h to 16 h. The grain size and density of the specimens were measured. From the measured data, the mechanisms of the densification and grain growth were determined by use of available kinetic equations which express the relations between densification and grain growth. In both atmospheres, it has been found that the densification was controlled by the lattice diffusion and the grain growth by the surface diffusion of atoms around pores. It appears that the surface diffusivity as well as the lattice diffusivity increase considerably with the increase in O/U ratio in the specimen.

• Journal of Powder Materials
• /
• v.17 no.2
• /
• pp.154-159
• /
• 2010

In this study, the sintering behavior of (Nd, Dy)-Fe-B powder which fabricated by strip-casting was investigated with various sintering temperatures and holding times. The relative density over 99% could be obtained by both sintering at $1070^{\circ}C$ for 1h and sintering at $970^{\circ}C$ for 20h. The grain growth was observed in sintered specimen at $1050^{\circ}C$ compared to one at $970^{\circ}C$. The isothermal sintering process below $1000^{\circ}C$ led to suppress grain growth showing the improved magnetic properties. The phase transformation of Nd-rich was confirmed by X-ray diffraction pattern.

• Journal of the Korean Society of Safety
• /
• v.21 no.1 s.73
• /
• pp.48-52
• /
• 2006

This study is a research of safety valve development for LP gas cylinder which use sintering metal. Re-searcher wishes to apply technology of sintering metal for safety valve development and do gas flow control. The basis of this study is most suitable fluid examination that to reduce gas accident. This research concluded following results. 1. When press pin length is 42mm to 45mm powder quantity is 0.25g, in case of press pin length 36mm to 42mm powder quantity is 0.2g, displayed fluid optimization. 2. When press pin length is 39mm and powder quantity is 0.25g, press pressure displayed fluid optimization at all interests from $1.2\;tons/cm^{2}\;to\;2\;tons/cm^{2}$. 3. When apparent density is about $5.0g/cm^{3}\;to\;4.5g/cm^{3}$, fluid optimization becomes.

• Journal of the Korean Ceramic Society
• /
• v.26 no.4
• /
• pp.505-513
• /
• 1989

The sintering behavior and grain growth of ZnO in 99.0mol% ZnO-1.0mol% Bi2O3 which are the basic compositions of ZnO varistor were studied. The microstructrual observation confirmed that the final sintered density was mainly determined at the initial stage of sintering, i.e. grain rearrangement and grain growth which were induced by the penetration of eutectic melts formed at eutectic temperature(74$0^{\circ}C$). But when the liquid penetration was terminated, the grain growth did not promote further densification. Activation energy of the grain growth of ZnO in the system of 99.0mol% ZnO-1.0mol% Bi2O3 was 44.8$\pm$1.8Kcal/mol.