• Resources Recycling
• /
• v.7 no.4
• /
• pp.50-54
• /
• 1998

In order to obtain desired electromagnetic propertieι high initial permeability and good frequency dependance of initial p permeability, the adding effects of sevral seeds were experimented in Mn-Zn ferrite system. As adding seed grams, calcined at sintering temperature, abnormal grains were disappeared clearly but the density and the initial permcability of sintered Mn-Zn ferrite body were decreased. On the contrary, in case of adding seed rains which were calcined below the calcination temperatnre of matrix particle, abnormal grains remained but the initial permeability was increas$\xi$d with proper s$\xi$ed content. W With proper seed content, the initial permeability was increased by 10-20% but tbe $\alpha$ltoff frequency was not changed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.160-162
• /
• 2003

ZnO epilayer were synthesized by the pulesd laser deposition(PLD) process on $Al_2O_3$ substrate after irradiating the surface of the ZnO sintered pellet by the ArF(193nm) excimer laser. The substrate temperatures was $400^{\circ}C$. The crystalline structure of epilayer was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of ZnO epilayer measured with Hall effect by van der Pauw method are $8.27{\times}10^{16}\;cm^{-3}\;and\;299\;cm^2V{\cdot}s$ at 293 K, respectively. The temperature dependence of the energy band gap of the ZnO obtained from the absorption spectra was well described by the Varshni's relation, $E_g(T)\;=\;3.3973\;eV\;-\;(2.69{\times}10^{-4}\;eV/K)T^2/(T\;+\;463K)$. After the as-grown ZnO epilayer was annealed in Zn atmospheres, oxygen and vaccum the origin of point defects of ZnO atmospheres has been investigated by the photoluminescence(PL) at 10 K. The native defects of $V_{Zn}$, Vo, $Zn_{int}$, and $O_{int}$ obtained by PL measurements were classified as a donors or accepters type.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.1
• /
• pp.46-55
• /
• 2002

10mo1% Gd$_2$O$_3$ doped CeO$_2$ fine powders were synthesized by the oxalate coprecipitation method. The characteristics and sintering behavior of fine powders were investigated. The oxalate precipitates had the specific surface area of 150$m^2$/g, and appeared to be fine and spherical primary particles with a size of approximately 5.5nm. The decomposition of the precipitates occurred from a temperature around 30$0^{\circ}C$ and it was completed below 40$0^{\circ}C$, resulted in the formation of the oxide. The calcination temperature of the fine powders was suitable at 77$0^{\circ}C$. By introducing fine powders washed with alcohol and ball-milling process after calcination, the sintered body was possible to attain the value of 97% of the theoretical density at low temperature of 130$0^{\circ}C$

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.332-333
• /
• 2005

In this study, in order to develop low temperature sintering piezoelectric actuator, $Pb(Mg_{1/2}W_{1/2})_{0.03}(Ni_{1/3}Nb_{2/3})_x(Zr_{0.50},Ti_{0.50})_{1-x-0.03}$ (PMW-PNN-PZT) ceramic systems were fabricated using $CaCO_3-Li_2CO_3$ sintering aid and their dielectric and piezoelectric properties were investigated with the variation of PNN substitution. The piezoelectric actuator requires high piezoelectric constant $d_{33}$ and high electromechanical coupling factor kp. At the PMW-PNN-PZT ceramics with 9mol% PNN substitution sintered at $900^{\circ}C$, the density, electromechanical coupling factor kp, dielectric constant, piezoelectric constant $d_{33}$ and mechanical quality factor Qm showed the excellent values of 7.86 [$g/cm^3$], 0.584, 1881, 485 [pC/N] and 76, respectively for piezoelectric actuator application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.305-306
• /
• 2005

In this paper, in order to develop Pb-free piezoelectric ceramics, $(Li_{0.04}Na_{0.44}K_{0.52})(Nb_{0.86}Ta_{0.10}Sb_{0.04})O_3$ ceramics were fabricated with the variation of calcination temperature and sintering temperature. Specimens couldn't be sintered below $111^{\circ}C$ and showed the largest density at calcination temperature of $800^{\circ}C$. Specimens manufactured with the variation of calcination temperature showed pseudo-tetragonal phase, and showed the optimal values of kp=0.45, ${\varepsilon}r$=1336 and $d_{33}$=254 at calcination temperature of $800^{\circ}C$ and sintering temperature of $1110^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.66-67
• /
• 2005

In this study, in order to develop multilayer piezoelectric actuator, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3-Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated with the function of PNN substitution. With increasing PNN substitution, dielectric constant(${\varepsilon}r$), electromechanical coupling factor(kp), and piezoelectric d constant($d_{33}$) were increased at 10~12[mol%] PNN substitution and then decreased at all sintering temperature. With increasing PNN substitution, phase changed from tetragonal to rhombohedral at [10~12mol%] PNN substitution. At the 12[mol%] PNN substituted PMN-PZT composition ceramic sintered at 950[$^{\circ}C$], density, ${\varepsilon}r$, kp, $d_{33}$ and Qm showed the optimum value of 7.79[$g/cm^3$], 1160, 0.599, 419[pC/N) and 894, respectively for multilayer piezoelectric actuator application.

• Korean Journal of Materials Research
• /
• v.19 no.7
• /
• pp.397-402
• /
• 2009

In this study, Ti powder was fabricated from Ti scrap by the Hydrogenation-Dehydrogenation (HDH) method. Hydrogenation reactions of Ti scrap occurred at near 450 $^{\circ}C$ with a sudden increase in the reaction temperature and the decreasing pressure of hydrogen gas during the hydrogenation process in the furnace. The dehydrogenation process was also carried out at 750 $^{\circ}C$ for 2hrs in a vacuum of $10^{-4}$ torr. After the HDH process, a deoxidation treatment was carried out with the Ca(purity: 99.5) at 700 $^{\circ}C$ for 2hrs in the vacuum system. It was found that the oxidation content of Ti powder that was deoxidized with Ca showed noticeably lower values, compared to the content obtained by HDH process. In order to fabricate Ti compacts, Ti powder was sintered at $1100\sim1400^{\circ}C$ for 2hrs under a vacuum of $10^{-4}$ torr. The relative density of compact was 94.9% at 1300 $^{\circ}C$. After sintering, all of the Ti compacts showed brittle fracture behavior, which occurred in an elastic range with short plastic yielding up to a peak stress.

• Korean Journal of Materials Research
• /
• v.17 no.10
• /
• pp.526-531
• /
• 2007

The sintering behavior and electrical property of $Ce_{0.8}Gd_{0.2}O_{1.9}$ ceramics were investigated with the iron oxide concentration ranging from 0 to 5 mol%. Both the sintered density and grain size were found to increase up to 2 mol% $Fe_2O_3$, and then to decrease with further additions. At a higher $Fe_2O_3$ content above 3 mol%, grain size decreased by a pinning effect induced by different shape grains. The electrical conductivity was also increased with increasing $Fe_2O_3$ content up to 2 mol%. Total conductivity of 2 mol% $Fe_2O_3-added$ specimen showed the maximum conductivity of $2{\times}10^{-2}{\Omega}{\cdot}cm^{-1}$ at $500^{\circ}C$. The addition of $Fe_2O_3$ was found to promote the sintering properties and electrical conductivities of $Gd_2O_3-dope\;CeO_2$.

• Korean Journal of Metals and Materials
• /
• v.46 no.6
• /
• pp.390-401
• /
• 2008

The objective of this study is to evaluate various machining characteristics of AlN-hBN machinable ceramics in micro end-milling process for its further application. First, AlN based machinable ceramics with hBN contents in the range of 10 to 20vol% were prepared by hot-pressing. Material properties of the composites, such as relative density, Vickers hardness, flexural strength, Young's modulus and fracture toughness were measured and compared. Then, micro end-milling experiments were performed to fabricate micro channels using prepared system. During the process, cutting forces, vibrations and AE signals were measured and analyzed using applied sensor system. Machined micro channel shapes and surface roughness were measured using 3D non-contact type surface profiler. From the experimental results, it can be observed that the cutting forces, vibrations and AE signal amplitudes decreased with increasing hBN contents. Also, measured surface roughness and profiles were improved with increasing hBN contents. As a result of this study, optimum machining conditions can be determined to fabricate desired products with AlN-hBN machinable ceramics based on the experimental results of this research.

• Korean Journal of Metals and Materials
• /
• v.50 no.6
• /
• pp.449-454
• /
• 2012

Nanopowder of FeAl and $Al_2O_3$ was synthesized from FeO and Al powders by high energy ball milling. Using the pulsed current activated sintering method, the nanocystalline $Al_2O_3$ reinforced FeAl composite was consolidated within two minutes from mechanically synthesized powders. The advantage of this process is that it allows very quick densification to near theoretical density and prohibits grain growth in nanostuctured materials. The grain size, sintering behavior and hardness of sintered $FeAl-Al_2O_3$ composite were investigated.