• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.738-739
• /
• 2006

This paper will describe a powder and processing method that facilitates single press-single sintered densities approaching $7.5g/cm^3$. At this sintered density, mechanical properties of the powder metal (P/M) component are significantly improved over current P/M technologies and begin to approach the performance of wrought steels. High performance gears have the added requirement of rolling contact fatigue durability that is dependent upon localized density and thermal processing. Combining high density processing of engineered P/M materials with selective surface densification enables powder metal components to achieve rolling contact fatigue durability and mechanical property performance that satisfy the performance requirements of many high strength automotive transmission gears. Data will be presented that document P/M part performance in comparison to conventional wrought steel grades.

• 한국분말재료학회지
• /
• 제5권1호
• /
• pp.35-41
• /
• 1998

The effect of Mn on the densification and the microstructural change in W heavy alley was investigated with adopting the improved Mn-adding method. In order to avoid the pore formation problems associated with Mn powder mixing to the other constituent powders, Mn was added afterwards to the sintered heavy alloy; Mn powder was spread homogeneously on the surface of the sintered heavy alloy compact, and this Mn powder contained specimen was resintered at the same sintering temperature. As expected, the resintered specimen showed the pore free microstructure because Mn was reduced separately from the other constituent elements. It was also founded that W grains grew rapidly at the initial stage of resintering treatment due to the activated reprecipitation of the excess W atoms substituted by Mn atoms, but the growth rate of W grains was slowly lowered with the prolonged sintering time, especially, compared to the Mn free heavy alloy. Such a retardation of grain growth should be attributed to the decreased W solubility in the Mn contented matrix phase. Furthermore, Mn addition resulted in the decrease of contiguity by improving the wetting between matrix phase and W grain.

• 한국세라믹학회지
• /
• 제31권1호
• /
• pp.55-61
• /
• 1994

Mn-Zn ferrite powder was obtained by wet method that was to be coprecipitated the metal ions of Fe2+, Mn2+ and Zn2+ with alkali solution. The target composition of the ferrite powder was 52 mol% Fe2O3, 24 mol% MnO, and 24 mol% ZnO, that was based on the region of high permeability. And the other ferrite powder was prepared by the dry method that was to be mixed the metal oxides as the above chemical composition. The wet method was compared with dry method for the powder properties and the electromagnetic characteristics of sintered cores. The synthesized powder by wet method was smaller particle size, narrower particle distribution, and higher purity than that of dry method. The initial permeability of sintered sample prepared by the wet method was 14000~28000, on the other side, 9000~15500 in case of the dry method.

• 한국분말재료학회지
• /
• 제8권1호
• /
• pp.35-41
• /
• 2001

$BaTiO_3$ fine powder was synthesized by hydrothermal process from the mixture of titania-hydroxide($TiO_2{\cdot}xH_2O$) and barium hexa-hydroxide ($Ba(OH)_2{\cdot}8H_2O$) as starting materials. Fine powder(< 100 nm) was made under the reaction conditions of 18$0^{\circ}C$,10 atm, 1.5 hr in autoclave and showed cubic structure. The powders were sintered by a spark plasma sintering technique from 1050~115$0^{\circ}C$ for 5 min. The grains of sample sintered at 110$0^{\circ}C$ were about 0.9${\mu}m$ in average size and showed the mixture of cubic and tetragonal structures.

• 한국분말재료학회지
• /
• 제3권3호
• /
• pp.167-173
• /
• 1996

The effect of ball milling on the pressureless sintering of MoSi$_2$ was investigated. Ball milling was conducted at 70 rpm for 72 hours using different balls and vessels: one used tungsten carbide balls in a plastic vessel(referred as B-powder) and the other stainless steel ball in a stainless steel vessel(referred as C- powder). The powder was compacted with 173MPa and subsequently sintered at the temperature range of 1150 $^{\circ}C$ and 1450 $^{\circ}C$ in H$_2$, atmosphere. Sintered density was measured and scanning electron micrograph was observed. Over 90% of the theoretical density was attained at 1250 $^{\circ}C$ within 10 minutes for C-powders, while the similar densification required a sintering temperature of 1450 $^{\circ}C$ for B-powders. Such a difference in sinterability between B and C-powders was discussed in terms of the effect of particle size reduction and activated sintering caused by Ni and/or Fe introduced during ball milling.

• 한국산학기술학회논문지
• /
• 제6권6호
• /
• pp.468-472
• /
• 2005

유리병의 제조에 있어서 유리 융체가 금형 벽면에 부착하는 것을 방지하기 위하여 성형할 때마다 금형 내벽면을 윤활제로 도포하는 공정이 있다. 금형 벽면을 통기성이 있는 다공질 소결체로 제조하면 도포공정을 생략할 수 있다. 따라서 본 연구에서는 스테인리스 중에서 내열${\cdot}$내마모 특성이 가장 우수한 310L계 조대 분말($-150{\mu}m$) 및 420J2 계 미세 분말($40{\~}50{\mu}m$)을 사용, 유리 금형용 내벽면 재로서 가장 적합한 다공질 소결체(소결체의 밀도: $85{\~}90\%$)를 제작하기 위하여 성형압력, 소결 분위기, 소결온도 및 시간을 변화시켜 다음과 같은 결과를 얻었다. (1) 고상 소결로서는 입자 크기가 큰 310L분말을 가지고는 어느 경우에 있어서나, 목적하는 소결 밀도를 얻을 수 없었다. (2) $2ton/cm^2$의 성형압력으로 성형한 실형상 성형체를 양산용 진공($1300^{\circ}C$, 2시간) 소결로에서 소결한 결과, 소결체의 밀도는 $310L+0.03\%B$, 420J2, 420J2+(0.03, 0.06)$\%$B에서 각각 6.2(79$\%$), 6.6(86$\%$), 7.3(95$\%$), $7.6(99\%)g/cm^3$로 나타났다. 따라서, 420J2계 분말(저압성형) 및 310L+0.03$\%$B(고압성형)분말을 사용하여 진공 중 소결하면 목적하는 통기도를 가진 소결체를 제작할 수 있다는 것을 알았다.

• 한국분말재료학회지
• /
• 제15권5호
• /
• pp.352-358
• /
• 2008

The present study focused on the synthesis of a bismuth-antimony-tellurium-based thermoelectric nanopowders using plasma arc discharge process. The chemical composition, phase structure, particle size of the synthesized powders under various synthesis conditions were analyzed using XRF, XRD and SEM. The powders as synthesized were sintered by the plasma activated sintering. The thermoelectric properties of sintered body were analyzed by measuring Seebeck coefficient, specific electric resistivity and thermal conductivity. The chemical composition of the synthesized Bi-Sb-Te-based powders approached that of the raw material with an increasing DC current of the are plasma. The synthesized Bi-Sb-Te-based powder consist of a mixed phase structure of the $Bi_{0.5}Sb_{1.5}Te_{3}$, $Bi_{2}Te_{3}$ and $Sb_{2}Te_{3}$ phases. This powder has homogeneous mixing state of two different particles in an average particle size; about 100nm and about 500nm. The figure of merit of the sintered body of the synthesized 18.75 wt.%Bi-24.68 wt.%Sb-56.57 wt.%Te nanopowder showed higher value than one of the sintered body of the mechanically milled 12.64 wt.%Bi-29.47 wt.%Sb-57.89 wt.%Te powder.

• 한국분말재료학회지
• /
• 제24권5호
• /
• pp.357-363
• /
• 2017

In this study, Bi-Sb-Te thermoelectric materials are produced by mechanical alloying (MA) and spark plasma sintering (SPS). To examine the influence of the milling atmosphere on the microstructure and thermo-electric (TE) properties, a p-type Bi-Sb-Te composite powder is mechanically alloyed in the presence of argon and air atmospheres. The oxygen content increases to 55% when the powder is milled in the air atmosphere, compared with argon. All grains are similar in size and uniformly, distributed in both atmospheric sintered samples. The Seebeck coefficient is higher, while the electrical conductivity is lower in the MA (Air) sample due to a low carrier concentration compared to the MA (Ar) sintered sample. The maximum figure of merit (ZT) is 0.91 and 0.82 at 350 K for the MA (Ar) and MA (Air) sintered samples, respectively. The slight enhancement in the ZT value is due to the decrease in the oxygen content during the MA (Ar) process. Moreover, the combination of mechanical alloying and SPS process shows a higher hardness and density values for the sintered samples.

• 한국재료학회지
• /
• 제30권5호
• /
• pp.231-238
• /
• 2020

The composition of martensite transformation in NiAl alloy is determined using pure nickel and aluminum powder by vacuum hot press powder metallurgy, which is a composition of martensitic transformation, and the characteristics of martensitic transformation and microstructure of sintered NiAl alloys are investigated. The produced sintered alloys are presintered and hot pressed in vacuum; after homogenizing heat treatment at 1,273 K for 86.4 ks, they are water-cooled to produce NiAl sintered alloys having relative density of 99 % or more. As a result of observations of the microstructure of the sintered NiAl alloy specimens quenched in ice water after homogenization treatment at 1,273 K, it is found that specimens of all compositions consisted of two phases and voids. In addition, it is found that martensite transformation did not occur because surface fluctuation shapes did not appear inside the crystal grains with quenching at 1,273 K. As a result of examining the relationship between the density and composition after martensitic transformation of the sintered alloys, the density after transformation is found to have increased by about 1 % compared to before the transformation. As a result of examining the relationship between the hardness (Hv) at room temperature and the composition of the matrix phase and the martensite phase, the hardness of the martensite phase is found to be smaller than that of the matrix phase. As a result of examining the relationship between the temperature at which the shape recovery is completed by heating and the composition, the shape recovery temperature is found to decrease almost linearly as the Al concentration increases, and the gradient is about -160 K/at% Al. After quenching the sintered NiAl alloys of the 37 at%Al into martensite, specimens fractured by three-point bending at room temperature are observed by SEM and, as a result, some grain boundary fractures are observed on the fracture surface, and mainly intergranular cleavage fractures.

• 한국분말재료학회지
• /
• 제21권3호
• /
• pp.215-221
• /
• 2014

Translucent alumina is a potential candidate for high temperature application as a replacement of the glass or polymer. Recently, due to the increasing demand of high power light emitting diode (LED), there is a growing interest in the translucent alumina. Since the translucent property is very sensitive to the internal defect, such as voids inside or abnormal grain growth of sintered alumina, it is important to fabricate the defect-free product through the fabrication process. Powder injection molding (PIM) has been commonly applied for the fabrication of complex shaped products. Among the many parameters of PIM, the flowability of powder/binder mixture becomes more significant especially for the shape of the cavity with thin thickness. Two different positions of the gate were applied during PIM using the disc type of die. The binder was removed by solvent extraction method and the brown compact was sintered at $1750^{\circ}C$ for 3 hours in a vacuum. The flowability was also simulated using moldflow (MPI 6.0) with two different types of gate. The effect of the flowability of powder/binder mixture on the microstructure of the sintered specimen was studied with the analysis of the simulation result.