• Electronics and Telecommunications Trends
• /
• v.38 no.6
• /
• pp.41-51
• /
• 2023

Heat dissipation technology for semiconductors and electronic packaging has a substantial impact on performance and lifespan, but efficient heat dissipation is currently facing limited improvement. Owing to the high integration density in electronic packaging, heat dissipation components must become thinner and increase their performance. Therefore, heat dissipation materials are being devised considering conductive heat transfer, carbon-based directional thermal conductivity improvements, functional heat dissipation composite materials with added fillers, and liquid-metal thermal interface materials. Additionally, in heat dissipation structure design, 3D printing-based complex heat dissipation fins, packages that expand the heat dissipation area, chip embedded structures that minimize contact thermal resistance, differential scanning calorimetry structures, and through-silicon-via technologies and their replacement technologies are being actively developed. Regarding dry cooling using single-phase and phase-change heat transfer, technologies for improving the vapor chamber performance and structural diversification are being investigated along with the miniaturization of heat pipes and high-performance capillary wicks. Meanwhile, in wet cooling with high heat flux, technologies for designing and manufacturing miniaturized flow paths, heat dissipating materials within flow paths, increasing heat dissipation area, and reducing pressure drops are being developed. We also analyze the development of direct cooling and immersion cooling technologies, which are gradually expanding to achieve near-junction cooling.

• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.1
• /
• pp.15-22
• /
• 2003

Experiments were conducted to evaluate the effect of blastomere diameters and cell cycle stages on the subsequent development of nuclear transplant rabbit embryos (NT-embryos) using nuclei derived from the 16- or 32-cell stage embryos. All blastomeres and NT-embryos were cultured individually in modified Ham's F-10 medium supplemented with 10% rabbit serum (RS) at $38^{\circ}C$ and 5% $CO_2$ in air. The diameter of blastomeres from 16-cell stage embryos was found twice of those from 32-cell stage (51 vs 27 ${\mu}m$). Significant differences were observed in cleavage rates ($\geq$3 divisions) in the isolated single blastomeres (54 vs 48 for 16-cell; 28 vs 14 for 32-cell, p<0.05), but the fusion rates of oocytes with transferred nuclei were similar between small and large single blastomeres derived from either 16-cell or 32-cell stage embryos. When 16-cell stage blastomeres were used as nuclear donors, cleavage rates ($\geq$3 divisions) of the NT-embryos were greater in the small nuclear donors than in the large donors (73 vs 55%, p<0.05). On the contrary, significantly higher cleavage (43 vs 6%, p<0.05) and developmental rates (14 vs 0%, p<0.05) were observed in the large blastomere nuclear donor group of the 32-cell stage embryos. When the cell cycle stages were controlled by a microtubule polymerization inhibitor (Demicolcine, DEM) or the combined treatment of DEM and Aphidicolin (APH), a DNA polymerase inhibitor, fusion rates were 88-96% for the 16-cell donor group (without DEM treatment), which were greater than the 32-cell donor group (54-58%). Cleavage rates were also greater in the transplants derived from G1 nuclear donor group (93-95%) than those from the DEM and APH combined treatment (73%) for the 16-cell donor group (p<0.05). No significant difference was detected in the morula/blastocyst rates in either donor cell stage (p>0.05). In conclusion, it appeared that no difference in the developmental competence between large and small isolated blastomeres was observed. When smaller 16-cell stage blastomeres were used as nuclear donor, the cleavage rate or development of NT-embryos was improved and was compromised when 32-cell stage blastomeres were used. Therefore, control nuclear stage of the donor cell at $G_1$ phase in preactivated nuclear recipients seemed to be beneficial for the cleavage rate of the reconstructed embryo in the 16-cell transplant, but not for subsequent morula or blastocyst development.

• Korean Journal of Food Science and Technology
• /
• v.29 no.3
• /
• pp.516-521
• /
• 1997

Effect of amylose content on the physical properties of resistant starches (RS) from autoclaved maize starches (with starch:water=1:3.5, at $121^{\circ}C$) which were repeated up to 4 times heating-cooling cycles, were investigated by water uptake, scanning electron microscope (SEM) and differential scanning calorimetry (DSC). Amylose content of waxy maize starch (Amioca), common maize starch (PFP), high amylose starch(Amaizo, Amylomaize VII) were 0%, 29%, 50%, and 72%, respectively. Yield of RS increased as amylose content increased. Water uptake of all kinds of native starch was higher than that of RS, but lower than that of autoclaved starch. By SEM, RS showed some small particles on surface but the size of particles was different with amylose content. Single endothermic transition peak exhibited at $40{\sim}70^{\circ}C$ in autoclaved Amioca and PFP (crystalline melting of amylopectin) and at $132{\sim}169^{\circ}C$ in autoclaved Amaizo and Amylomaize VII(crystalline melting of amylose) by DSC. RS from all kinds of autoclaved starches except Amioca showed single endothermic peak over $155^{\circ}C$ but the enthalpy was not related to amylose content.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.6
• /
• pp.67-76
• /
• 2005

This paper proposes a compact-sized surface myoelectric sensor for the myoelectric hand prosthesis. To fit the surface myoelectric sensor in the socket for the myoelectric hand prosthesis, the sensor should be a compact size. The surface myoelectric sensor is. composed of a skin interface and a single processing circuit that are mounted on a single package. The skin interface has one reference and two input electrodes, and the reference electrode is located in the center of two input electrodes. In this paper we propose two types of sensors with the circle- and bar-shaped reference electrode, but all input electrodes are the bar-shaped. The metal material of the electrodes is the stainless steel (SUS440) that endures sweat and wet conditions. Considering the conduction velocity and the median frequency of the myoelectric signal, we select the inter-electrode distance (IED) between two input electrodes as 18mm, 20mm, and 22 mm. The signal processing circuit consists of a differential amplifier with a band pass filter, a band rejection filter for rejecting 60Hz power-line noise, amplifiers, and a mean absolute value circuit. We evaluate the proposed sensor from the output characteristics according to the IED and the shape of the reference electrode. From the experimental results we show the surface myoelectric sensor with the 18mm IED and the bar-shaped reference electrode is suitable for the myoelectric hand prosthesis.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.10a
• /
• pp.423-424
• /
• 2011

This paper has proposed a 920 MHz RF front-end for IEEE 802.15.4g SUN (Smart Utility Network) systems. The proposed 920 MHz RF front-end consists of a driver amplifier, a low noise amplifier, and a RF switch. In the TX mode, the driver amplifier has been designed as a single-ended topology to remove a transformer which causes a loss of the output power from the driver amplifier. In addition, a RF switch is located in the RX path not the TX path. In the RX mode, the proposed low noise amplifier can provide a differential output signal when a single-ended input signal has been applied to. A LC resonant circuit is used as both a load of the drive amplifier and a input matching circuit of the low noise amplifier, reducing the chip area. The proposed 920 MHz RF Front-end has been implemented in a 0.18-um CMOS technology. It consumes 3.6 mA in driver amplifier and 3.1 mA in low noise amplifier from a 1.8 V supply voltage.

• Journal of Aerospace System Engineering
• /
• v.16 no.5
• /
• pp.17-25
• /
• 2022

The pintle injector has many advantages in the key characteristics of a liquid rocket engine, such as combustion stability, combustion efficiency, and wide range of comprehensive thrust control, design and manufacture, and test fired under supercritical conditions. The pintle injector is manufactured with a rectangular, single-row orifice for thrust control and production considerations. In order to verify the combustion performance of the pintle injector and its potential as a commercial injector, the combustion characteristics were analyzed by varying the TMR (Total Momentum Ratio) and BF (Blockage Factor). The result of the hot firing test showed that the heat flux increased as TMR increased, and it confirmed that the characteristic velocity efficiency was more affected by BF than TMR. Suppose a single-row pintle injector with efficiency characteristics insensitive to changes in TMR can achieve high efficiency at low fuel differential pressure conditions. In that case, the variable pintle injector's design flexibility can be increase.

• Pediatric Infection and Vaccine
• /
• v.17 no.2
• /
• pp.169-176
• /
• 2010

Purpose : We aimed to evaluate predictive parameters for non-response to intravenous immunoglobulin (IVIG) in patients with Kawasaki disease (KD) before IVIG use using two controls. Methods : We evaluated 229 consecutive KD patients who were treated with 2 g/kg of IVIG at a single center. Those who had persistent fever >24 hours after IVIG infusion made up the 23 IVIG non-responders; the first control included a total 206 defervesced cases and the second control included 46 cases that were matched for age and pre-treatment fever duration to non-responders. Results : Demographic and clinical characteristics were similar in IVIG non-responders and responders at presentation. As for laboratory findings, the neutrophil differential, CRP, AST, ALT, and LDH were higher, and lymphocyte differential, total protein, albumin, platelet count, and total cholesterol were significantly lower in IVIG non-responders compared to responders by univariate analysis in both study designs. However in multivariate analysis, non-responders showed a significantly higher neutrophil differential (cutoff value, >77%, sensitivity 68.4% and specificity 79.5%) and lower cholesterol (<124 mg/dL, sensitivity 79% and specificity 70.5%). Whereas plasma albumin (<3.6 g/dL, sensitivity 73.7% and specificity 60%) was the sole laboratory parameter of non-responders in the second study design. Conclusion : Severity of inflammation in KD was reflected by higher or lower laboratory values at presentation. Because the multivariate analysis for these indices may be influenced by some confounding factors, including the numbers of patients of different ages and fever duration, other assessment modalities are needed for KD patients with the greatest risk of coronary artery lesions.

• Journal of Advanced Navigation Technology
• /
• v.11 no.4
• /
• pp.371-377
• /
• 2007

Ionospheric time delay is one of the main error source for single-frequency DGPS applications, including time transfer and Wide Area Differential GPS (WADGPS). Grid-based algorithm was already developed for WADGPS but that algorithm is not applicable to geomagnetic storm condition in accuracy and management. In geomagnetic storm condition, the spatial distribution of vertical ionospheric delay is noisy and therefore the accuracy of modeling become low in grid-based algorithm. For better accuracy, function based algorithm can be used but the continuity of correction message is not guranteed. In this paper, we propose the ionospheric model using wavelet based algorithm. This algorithm shows better accuracy with the same number of correction message than the existing spherical harmonics algorithm and guarantees the continuity of correction messages when the number of message is expanded for geomagnetic storm condition.

• Journal of Astronomy and Space Sciences
• /
• v.32 no.4
• /
• pp.335-340
• /
• 2015

Using the Total Electron Content (TEC) data from the Global Navigation Service System (GNSS) site in Jeju, operated by the Korea Astronomy and Space Science Institute (geographic location: $33.3^{\circ}N$, $126.5^{\circ}E$; geomagnetic location: $23.6^{\circ}N$) for 2002-2014 in Korea, the results of the statistical analysis of positive and negative ionospheric storms are presented for the first time. In this paper, ionospheric storms are defined as turbulences that exceed 50% of the percentage differential Global Positioning System (GPS) TEC ratio (${\Delta}TEC$) with monthly median GPS TEC. During the period of observations, the total number of positive ionospheric storms (${\Delta}TEC$ > 50%) was 170, which is greater than five times the number of negative ionospheric storms (${\Delta}TEC$ < - 50%) of 33. The numbers of ionospheric storms recorded during solar cycles 23 and 24 were 134 and 69, respectively. Both positive and negative ionospheric storms showed yearly variation with solar activity during solar cycle 23, but during solar cycle 24, the occurrence of negative ionospheric storms did not show any particular trend with solar activity. This result indicates that the ionosphere is actively perturbed during solar cycle 23, whereas it is relatively quiet during solar cycle 24. The monthly variations of the ionospheric storms were not very clear although there seems to be stronger occurrence during solstice than during equinox. We also investigated the variations of GPS positioning accuracy caused by ionospheric storms during November 7-10, 2004. During this storm period, the GPS positioning accuracies from a single frequency receiver are 3.26 m and 2.97 m on November 8 and 10, respectively, which is much worse than the quiet conditions on November 7 and 9 with the accuracy of 1.54 m and 1.69 m, respectively.

• Proceedings of the Korea Contents Association Conference
• /
• 2003.05a
• /
• pp.416-420
• /
• 2003

In this paper, we implemented a dual-resolution image database system for the fast naked-eye retrieval using interpolation. This system can solve two conventional problems : a blocking noise at zoom-out image in single high resolution method and a big storage to store in simple dual-resolution image database system. The proposed method makes a subsampled image by subsampling a original image, and then a interpolated image of it using interpolation. After that, a hybrid dual-resolution image database is composed based on the differential image between the interpolated image and the original image. Experimental results of simulating through 60 sample images shows that the proposed method is 0.011 second faster than simple high-resolution method in the retrieval time - one is 0.003 second, the other is 0.014 second, respectively. Also, that improves 14.7% more than simple dual-resolution method in the stored size - one is 19,821 byte, the other is 16,910 byte, respectively.