• 한국자동차공학회논문집
• /
• 제6권1호
• /
• pp.143-150
• /
• 1998

The evaluation of joint fatigue strength of light weight materials for electrical vehicle body has been performed through single lap joint tests with the design parameters such as joint style, adherend, bonding overlap length and bonding thickness. Fatigue strength was evaluated through 5-Hz, tension-tension, load controlled test with the stress ratio zero value. It is experimentally observed that fatigue strength of joint increases for the increase of overlap length. The combinations of Al-Al and Al-FRP adherends show that fatigue strength of joint is hardly changed for the increase of bonding thickness, but FRP-FRP adherend specimen shows that fatigue strength of joint increases after decreases for the increase of bonding thickness. Al-Al adherend specimen has much higher fatigue length than Al-FRP and FRP-FRP adherend specimens. Riveting at adgesive bonded joint gives little effect on fatigue strength.

• 대한기계학회논문집A
• /
• 제33권6호
• /
• pp.560-567
• /
• 2009

This paper was designed to estimate the adhesion strength of galvannealed coatings on steel sheets. The adhesion strength were evaluated using single lap - shear tests where the lap joint was bonded by structural adhesive. Tests were performed for overlap length of 5mm, 10mm and 15 mm and three directions (0, 45, 90) of steel sheets used as the adherend of the overlap joint. After the tests, FE simulations of the single lap-shear test were also carried out to observe the stress distribution in the interface between the adhesive and the coated sheet. The results showed that the joint failure loads obtained from the tensile tests of bonded single lap-joints were the same, regardless of overlap lengths and directions of steel sheets. Also, the failure of galvannealed coatings greatly depended on shear stress distribution in the interface and the value was about 30MPa.

• Composites Research
• /
• 제17권6호
• /
• pp.14-21
• /
• 2004

본 연구에서는 몇 가지 접합 방법에 따라 일방향 복합재료 단일 겹치기 접합 조인트의 파손 과정, 모드 및 강도를 실험적으로 평가하였다 접합 방법으로는 접착제 없는 동시성형, 접착제를 사용한 동시성형 및 이차 접합의 세 가지를 고려하였다 또한 이차 접합 조인트에서 몇 가지 파라미터의 영향도 살펴보았다. 접착제 없는 동시성형 시편은 가장 우수한 조인트 강도를 나타내었다. 이차접합 조인트에서는 접착제 층의 점진적인 파손이 발생하였다. 접착제의 재료 및 접합 강도가 상대적으로 강한 필름 접착제의 동시성형 조인트는 갑작스런 층간분리 파손이 발생하였으며 이차 접합 조인트보다 더 낮은 파손 강도를 나타내었다. 이차 집합 조인트에서 층간분리 파손이 발생하지 않은 것은 접착제 층에서의 균열 진전 및 점진적 파손이 층간분리 파손을 방지한 것으로 보인다. 따라서 복합재료 접합 조인트의 파손 강도는 접착제의 재료 강도 또는 접착 성능과 항상 비례하지 않으며 이것은 복합재료가 층간 분리 파손에 약하기 때문이다.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.835-845
• /
• 1994

In this paper, the effects of the adhesive thickness and adherend roughness on the static and fatigue strengths of the adhesively bonded circular single lap joints has been investigated by an experimental method. The stacking sequence effect of the composite adherend on the static and fatigue strength and the fracture patterns of the adhesive failure were also observed. Since the circular single lap joint fails catastrophically beyond the static strength of fatigue limit, the tubular polygonal adhesively bonded joints such as triangular, tetragonal, pentagonal, hexagonal as well as elliptical joints were manufactured in order to give partial mechanical characteristics to the adhesively bonded tubular joints. These joints were tested both in static and fatigue modes. From the experimental investigations, it was found that the fatigue strength of the circular adhesively bonded joints was much dependent on the arithmetical average surface roughness of the adherends and the polygonal adhesively bonded joints had better fatigue strength characteristics than the circular adhesively bonded joints.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.465-470
• /
• 2001

The adhesively-bonded joints considered in this investigation include single-lap joint and double-lap joint. For an adhesively bonded double-lap joint, end mismatch between the two cuter adherends(upper, lower) can not removed completely although it can be controlled within a manufacturing tolerance. This paper shows that the end mismatch introduces local bending and end mismatch affects the shear and peel stresses in the adhesive. The double-lap joint with an end mismatch is affected of adhesive thickness, material properties of adhesive and adherend etc. Also, we concluded that there are critical value of an end mismatch to provoke the interface fracture.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2004년도 추계학술발표대회 논문집
• /
• pp.73-77
• /
• 2004

Failure predictions of composite single-lap bonded joints were performed considering both of composite adherend failure and bondline failure. An elastic-perfectly plastic model of adhesive and a delamination failure criterion are used. The failure prediction results such as failure mode and strength have very good agreements with the test results of joint specimens with various bonding methods and parameters. The influence of variations in the effective strength (that is, adhesion performance) and plastic behavior of adhesive on the failure characteristics of composite bonded joints are investigated numerically. The numerical results show that optimal joint strength is archived when adhesive and delamination failure occur in the same time.

• 대한기계학회논문집A
• /
• 제35권3호
• /
• pp.333-340
• /
• 2011

본 연구에서는 복합소재 단일겹치기 조인트의 접착부재 형상 및 필렛 유무에 따른 응력집중 완화 효과를 평가하였다. 이를 위해 6가지 서로 다른 끝단부 형상에 대해 비선형 유한요소 해석을 수행하였다. 또한, 복합재 접착부재와 접착제의 다양한 강성비에 따른 6가지 모델의 최대 전단 및 수직응력의 변화를 고찰하였다. 접착부재가 순방향 테이퍼를 갖는 모델의 경우에는 가장 높은 응력값을 보여 조인트의 접합강도가 가장 취약할 것으로 예상되었다. 이에 반해, 접착부재가 역방향 테이퍼를 갖고 필렛이 존재할 경우 가장 낮은 응력값을 보였다. 접착부재와 접착제의 강성변화에 따른 최대응력 변화를 고찰한 결과 접착부재의 강성은 클수록, 접착제 강성은 낮을수록 응력집중은 완화되었다.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.183-190
• /
• 2000

The objective of this work is to develop a criterion for predicting the failure strength of the joints bonded by ductile adhesives. To obtain a criterion, first, fracture tests were carried out for T-peel joint and Single-lap joint with widely differing joints geometries. Then using the fracture loads obtained at tests, the finite element analysis were performed, in which the stresses in the adhesive bonds were calculated in great detail. After examining four epoxy adhesives, it is concluded that the fracture of adhesively bonded joint occurs when the maximum of the ratio of the mean to effective stresses exceeds a constant value which can be determined from analysis and test for each adhesive.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.62-67
• /
• 2012

In this study, the bonding strengths of adhesively bonded joints are experimentally investigated. A series of lap-shear tests are conducted using single lap type adhesive joints. In order to analyse the joint fabrication factors that affected the bonding strength, the parametric tests are conducted with various thickness of adhesive, surface roughness and fillet of adhesive. In addition, for the comparative study with the welded joint, lap-shear tests using specimens with 2 welded sides and 4 welded sides are also carried out. The quantitative results of the strength analysis are summarized, and some proposals are made on setting up testing standards for adhesively bonded joints.

• Composites Research
• /
• 제18권1호
• /
• pp.1-9
• /
• 2005

본 논문에서는 복합재료 접합 조인트의 다양한 파손 모드를 고려하여 파손 강도를 예측할 수 있는 방법을 제시하였다. 제시된 방법에서는 접착제의 탄성-완전 소성 재료 모델과 층간분리 파손 식을 이용해 접착제 파손 하중과 복합재료 부재의 층간분리 파손 하중을 동시에 계산하였다. 제시된 방법을 유한요소해석에 도입하여 복합재료 Single-Lap 접합조인트의 파손 예측을 수행하였으며 시험결과와 비교하였다 이를 통해 본 방법이 다양한 접합 방법에 따른 실제적인 파손모드 및 파손 하중을 정확하게 예측할 수 있음을 확인하였다. 또한 접착제의 유효강도(또는 접착 성능) 및 소성거동이 복합재료 접합 조인트의 파손 특성에 미치는 영향을 수치적으로 평가하였다. 이를 통해, 복합재료 접합조인트의 파손 강도는 접착제의 접착 성능과 항상 비례하지 않으며 층간분리 파손과 접착제 파손이 동시에 발생하도록 하는 것이 접합 조인트의 강도를 최대로 향상시킬 수 있음을 보였다.