• Fire Science and Engineering
• /
• v.21 no.4
• /
• pp.59-64
• /
• 2007

We studied on the fires about the electrical motors in this paper. We compared and analyzed about the transformation and damage state of single-phase induction motors used in the home appliances when we applied electrical overload and exterior flame. This experiment was progressed by the electrical overload application test and the exterior flame application test through the locked rotor of motor. In case of the exterior flame application test, it is divided into the apply voltage case and not apply voltage case. The result of an experiment through the locked rotor of motor, it was able to observe the short-circuit marks between layers at the winding coil parts, and it was appeared a transformed dendritic tissue structure of winding coil by the electrical overload test. The application voltage and the application exterior flame, it was confirmed that the stator winding coil parts were remain original shapes and observed that the color of the winding coil's circumference was changed to red. The non-application voltage and the application exterior flame, it was observed that the stator winding coil parts were transformed quite from original shapes. It was observed that the color of the winding coil and circumference parts was changed to red at the same case of non-application voltage.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.5-6
• /
• 2014

According to 2013 fire statistical yearbook in the National Emergency Management Agency, the main cause of an electrical fire are classified to short circuit fault, overload fault, electric leakage, partial disconnection, and joint/contact badness. The occurrence factor of fire is electric arc or spark accompanied with electrical faults. Residual Current Protective Devices(RCDs) of high sensitivity type used at single phase (220V) cut off earth leakage and overload but the RCDs can not cut off electric arc or spark to be a main cause of electrical fire. To be improved on such problem, this thesis is proposed to a auxiliary control device for RCD cut off electric arc or spark.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1193-1199
• /
• 1990

Effects of strain hardening exponents on the behavior of fatigue crack propagation are experimentally investigated. The retardation effect of fatigue crack propagation after single overloading is investigated in relation to strain hardening exponent and crack closure. A relationship between crack opening ratio and strain hardening exponents is inspected through an examination of the crack closure behavior. An empirical equation relating retardation effect of fatigue crack propagation after single overloading, percent peak load and strain hardening exponent of materials is proposed.

• Journal of the Korea Computer Industry Society
• /
• v.8 no.4
• /
• pp.237-244
• /
• 2007

In this paper we investigate the benefits of a data aggregation to prolong the lifetime of wireless sensor networks. To reduce the overload of messages from source node to sink node, data aggregation technique is generally used at intermediate node in path. The DD-G(Directed Diffusion-Greedy) can diminish the consumption of node energy by establishing energy effective single path from source to destination. In this case, the nodes near sink node have some problems, i) overly concentration of energy consumption, ii) increase of message delay time. To solve these problems, we propose a new data aggregation method which consider distribution of network overload, especially at the nodes close to sink node. The result shows that it can save energy and network delay time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.3 s.174
• /
• pp.567-580
• /
• 2000

This paper proposes an integrated approach, which is independent of specimen geometry and loading type, for predicting the fatigue life of spot welded specimens. We first establish finite element models reflecting the actual specimen behaviors observed on the experimental load-deflection curves of 4 types of single spot welded specimens. Using finite element models elaborately established, we then evaluate fracture parameter J-integral to describe the effects of specimen geometry and loading type on the fatigue life in a comprehensive manner. It is confirmed, however, that J-integral concept alone is insufficient to clearly explain the generalized relationship between load and fatigue life of spot welded specimens. On this ground, we introduce another effective parameter $J_e$ composed of $J_I$, $J_{II}$, $J_{III}$, which has been demonstrated here to more sharply define the relationship between load and fatigue life of 4 types of spot welded specimens. The crack surface displacement method is adopted for decomposition of J, and the mechanism of the mixed mode fracture is also discussed in detail as a motivation of using $J_e$.

• The Journal of the Acoustical Society of Korea
• /
• v.17 no.4E
• /
• pp.28-34
• /
• 1998

In most switching system, the processing unit is designed to work efficiently even at relatively high loads, but when the offered traffic exceeds a particular level, the rate of completed calls can fall drastically. A single call handled by the switching system consists of a sequence of events or messages that has to be processed by the control unit. The control unit is not only incapable of handling all of the offered calls, but also its call handling capability can drop as the offered load increases. The real time available for call processing is a critical resource that requires careful management. Therefore, the overloading of this resource must be detected by a subscriber in the from of a dial tone delay or an uncompleted call which is either blocked or mishandled. The subscriber may respond by either dialing prematurely or by re-attempting a call. This action can further escalate the processors load, which is spent for uncompleted calls. Unless a proper control is used, the switching system can finally break down. In this paper, we paper, we propose a fuzzy overload detection and control method for switching systems, which can by generating fuzzy rules via fuzzy aggregation networks. Simulation results involving a switching system is given.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.6
• /
• pp.1554-1561
• /
• 1998

When the superposition of realtime traffic and non-realtime traffic is applied to the ATM network, the successive cell loss(block loss) is more influential on the quality of service (QoS) of two traffic streams than the single loss in case of bursty traffic. Block loss can be identified as an important performance measure because of delay-oriented policy for realtime traffic. In this paper, we consider the system with the two-level overload control reducing of the recurrence of shut-down periods and develop a recursive algorithm to obtain both block loss and cell loss probabilities of both traffic. We can see that it gives the more precise and diverse investigations on performance analysis of queuing strategy.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.609-610
• /
• 2008

In this paper, a 110 dB, 1.024 MHz fourth-order single-loop Delta-Sigma sigma modulator has been presented with an over-sampling ratio of 128 and an overload factor of -6 dB for a bandwidth of 4 kHz. In particular, this ${\Sigma}-{\Delta}$ modulator is well suited for high accuracy measure systems. The whole modulator consumes only 3-mW from a single 3.3V supply in a $0.35-{\mu}m$ CMOS technology.

• Management Science and Financial Engineering
• /
• v.20 no.2
• /
• pp.7-12
• /
• 2014

Content Delivery Network (CDN) has evolved to overcome a network bottleneck and improve user perceived Quality of Service (QoS). A CDN replicates contents from the origin server to replica servers to reduce the overload of the origin server. CDN providers would try to achieve an acceptable performance at the least cost including the storage space or processing power. In this paper, we introduce a new optimization model for the CDN design problem considering the user perceived QoS and single path (non-bifurcated) routing constraints and analyze the computational complexity for some special cases.

• Journal of the Korean Society of Safety
• /
• v.7 no.1
• /
• pp.20-29
• /
• 1992

Effects of strain hardening exponents on the retardation behavior of fatigue crack propagation are experimentally investigated. The retardation of fatigue crack propagation seems to be induced by the crack closure at crack tip. The phenomenon of crack closure becomes remarkable with the increment of strain hardening exponent and magnitude of percent peak load. The ratio of crack growth increment(a$\_$d//w$\_$d/) is influenced by a single overloading (a$\_$d/) and estimated plastic zone size (W$\_$d/=2r$\_$y/) is increased according with the increasing of strain ha.dening exponents. The number of retarded crack growth cycles were (N$\_$d/) decreased as the baseline stress intensity factor .ange( K$\_$b/) was increased. Within the limitation of these experimental results obtained under the single overload, an empirical relation between crack retardation ratio (Nd/N＊), strain hardening exponent (n) and percent peak load (％PL) has been proposed as; Nd/N＊＝ exp [PL $.$ PL$.$A(n)＋B(n) ] where, A(n)＝${\alpha}$n＋${\beta}$, B(n)＝${\gamma}$n＋$\delta$, PL＝％PL/100 and ${\alpha}$＝0.78, ${\beta}$＝0.54, ${\gamma}$＝0.58 and $\delta$＝-0.01, It is interesting to note that all these constants are identical for materials such as aluminum(A3203), steel(S4SC), steel(SS41) and stainless steel(SUS316) used in this experimental study.