• Proceedings of the KIEE Conference
• /
• 1998.11a
• /
• pp.61-63
• /
• 1998

Disk type single phase SRM (DSPSRM) has a specific property of axial flux machine and radial flux machine simultaneously. So, this DSPSRM has a complicated magnetic circuit and it is difficult to analyze characteristics. Therefore, in this paper, the design specification of DSPSRM was calculated based on conventional design theory of electric machine and analyzed by 3D FEM. As the result of analysis, the approximated torque characteristics was obtained by finding the magnetic flux and energy distribution with the rotor position.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.968-979
• /
• 2019

Recently, there has been increased interest in the study of multiphase machines due to their higher fault-tolerant capability when compared to their conventional three-phase counterparts. For six-phase machines, stator windings configured with a single isolated neutral (1N) provide significantly more post-fault torque/power than two isolated neutrals (2N). Hence, this configuration is preferred in applications where post-fault performance is critical. It is well known that min-max injection has been commonly used for three-phase and multiphase machines in healthy condition to maximize the modulation limit. However, there is a lack of discussion on min-max injection for post-fault condition. Furthermore, the effects in terms of the common-mode voltage (CMV) in modulating signals has not been discussed. This paper investigates the effect of min-max injection in post fault-tolerant control on the voltage and speed limit of a symmetrical six-phase induction machine with single isolated neutral. It is shown that the min-max injection can minimize the amplitude of reference voltage, which maximizes the modulation index and post-fault speed of the machine. This in turn results in a higher post-fault power.

• Journal of the Korean Home Economics Association
• /
• v.9 no.2
• /
• pp.40-47
• /
• 1971

The purpose of this study was to examine the effects of several methods of the patching on the strength of the seam-texture. The main findings warranted from the present study were as follows : 1. The breaking strength was increased in proportion to the number of stitches in the case of 5 stitches per cm and 7 stitches per cm, not in the case of 9 stitches per cm where the tendency to damage the texture stitches appeared because of the excessive. 2. In comparing the effects of three methods (1. attaching a single patch, 2. attaching a single patch and seaming, 3. attaching several ply patch), no significant difference was found among these three. 3. There was a significant difference between the effects of two methods (1. attaching a single patch and stitching one edge of it on one side of the seam, 2. attaching a single patch and stitching both edges of it on the both sides of seam). In other words, the latter was found to be significantly more effective than the former. 4. In the case of unbalanced texture 9for example, single to two ply, single ply to two ply, or single to three ply), attaching a single patch to single ply and stitching both edges of it, and attaching a single patch to cover the plain-seam and stitching both edges of it, were more effective than attaching a single patch without stitching. 5. In comparing the effects of stitching both edges of the patch in 4 stitches per cm by the machine and by the hand, no significant difference was found. But these were more effective than stitching its both edges in 2 stitches per cm by hand. 6. The plain-seam stitched one edge of patch in 2 stitches per cm by machine and other by hand was significantly stronger than the plain-seam without a patch or with patch not stitched.

• Proceedings of the KIPE Conference
• /
• 2007.11a
• /
• pp.142-144
• /
• 2007

This paper proposes problem improvement in existing method about three-phase current reconstruction method and present minimum voltage injection method and Smooth voltage injection method in single current sensor for washing machine motor drive. So, presented wash noise improvement method through ripple reduction in inverter. The simulation and experimental results are given to show the effectiveness of the proposed method for reconstructing the phase currents and reducing the noises.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.1 no.3
• /
• pp.266-273
• /
• 2012

In conventional direct torque control (DTC) using space-vector modulation (SVM) of induction machine (IM) drives, at least three current sensors are needed. In this paper, a low-cost SVM-DTC strategy is proposed, in which only a single current sensor is used. The position of the voltage space vector is divided into two areas: effective and non-effective area. If it is located in the non-effective area, the voltage space vector will be shifted into the effective area with minimum distortion. Further, the switching frequency remains constant. The simulation is carried out on a MATLAB/Simulink platform and the simulated results verify the effectiveness of the proposed strategy.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.4
• /
• pp.1558-1565
• /
• 2018

Three-phase current is reconstructed from the dc-link current in an AC machine drive with a single current sensor. Switching pattern modification methods, in which the magnitude of the effective voltage vector is secured over its minimum, are investigated to accurately reconstruct the three-phase current. However, the existing methods that modify the switching pattern cause voltage and current distortions that degrade sensorless performance. This paper proposes a variable-magnitude voltage signal injection method based on a high frequency voltage signal injection. The proposed method generates a voltage reference vector that ensures the minimum magnitude of the effective voltage vector by varying the magnitude of the injection signal. This method can realize high quality current reconstruction without switching pattern modification. The proposed method is verified by experiments in a 600W Interior permanent magnet synchronous machine (IPMSM) drive system.

• Journal of Korean Society of Forest Science
• /
• v.111 no.4
• /
• pp.583-593
• /
• 2022

The harvesting system in South Korea faces the problems of aging workers and high wages, so it is necessary to improve the operation system and train workers to use high-performance forestry machines. This study compared the effectiveness and costs of yarding and processing operations between a multi-operation system using a tower yarder (HAM300) and a processor (KESLA 20SH) with those of a single-system using a forestry combi-machine. A whole-tree (cable) yarding operation was conducted in the clear-cutting area located at Compartment 15, Gwangneung Experimental Forest, National Institute of Forest Science, and the productivity and cost of multi- and single-system were analyzed. The productivity of the single-system was 1.5 m³/PMH and 1.6 m³/PMH higher than that of the multi- system because the single-system produced 1 log/cycle more than the multi-system in the yarding operation. The cost was approximately 12.1% lower for the single-system (￦36,113/m³) than for the multi-system (￦41,065/m³). The costs of the single-system and multi-system were decreased by maximums of 22.6% and 15.9%, respectively, by decreasing the idle time.

• Korean Management Science Review
• /
• v.12 no.3
• /
• pp.177-185
• /
• 1995

This paper presents a Tabu Search method to minimize a number of tardy jobs in the nonidentical parallel machine scheduling. The Tabu Search method employs a restricted neighborhood for the reduction of computation time. In this paper, we use two different types of method for a single machine scheduling. One is Moore's algorithm and the other is insertion method. We discuss computational experiments on more than 1000 test problems.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.17 no.30
• /
• pp.107-116
• /
• 1994

This paper formulates a dynamic monitoring and control model with a machine state by quality variations in a single lot production system. A monitoring model is based on estimate of machine state obtained using control theory. The model studied in this paper has a great advance from a point of view the combination between quality control (Sampling, Control Chart) and automatic control theory, and can be extended in a several ways.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.437-442
• /
• 2013

For open-end permanent magnet synchronous machine(PMSM) with dual inverter system, where one inverter is connected to the source and the other is flying, the dc link voltage of the flying inverter can be boosted through the machine. For this reason, when compared with single inverter drive system, higher voltage can be applied to PMSM, and higher torque can be generated in the flux weakening region. In this case, however, active and reactive powers are separately supplied by each inverter to maintain the dc link voltage of flying inverter. Therefore, the required flux weakening control is different from the conventional method for a single inverter drive system. This paper proposes the novel flux weakening control method which maximizes the active voltage component in a dual inverter PMSM drive system. The proposed method was demonstrated and verified through experimental results.