• Magazine of the Korean Society of Agricultural Engineers
• /
• v.30 no.4
• /
• pp.45-61
• /
• 1988

The purpose of this study is to develop regression equations between annual specific sedi- ment of reservoirs and physiographic factors of watersheds. 122 irrigation reservoirs, which have irrigation areas equal to or larger than 200 ha, located in Korea except Cheju province are used in the analysis. Simple regression analyses between the specific annual sediment and each of the physical characteristic factors of the reservoirs are carried out at first. Then, multiple regression analyses between the annual specific sediment and the physical characteristic factors with high correlation coefficients in the simple regression analyses are made. The results obtained from this study are as follows : 1. The results of the sirnple regression analyses show that in each province the watershed area, the length of mainstream, the circumferential length of watershed have high cor- relation coefficients (R=0.814-0.986), and that drainage density, reservoir capacity per watershed area, drainage frequency, basin relief have low correlation coefficients (R=0. 387-0.955). 2. The purposed multiple regression equations between the annual specific sediment of reservoirs and three major characteritic factors of watersheds, namely, the watershed area, the circumferential length of watershed, and the length of mainstream, are proposed as given in Table 2. 3. The result of the simple regression analyses with respect to the reservoir elevation except Jeonnam province, which has very different characteristics comparing to other provinces, shows that watershed area, main stream length and circumferential length have high correlation coefficients (R=0.806-0.884) in low-elevation reservoirs and intermediate- elevation reservoirs, but low correlation coefficients (R=0.639-0.739) in high-elevation reservoirs. 4. With respect to the reservoir elevation, the proposed multiple regression equations bet- ween the annual specific sediment of reservoirs and the three major characteristic factors of watershed which have high correlation coefficients are proposed as given in Table 5.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.43 no.2
• /
• pp.101-104
• /
• 1998

This study was conducted to establish a rapid analysis method for determining protein and moisture contents of pea. Ninety and eighty pea (Pisum sativum L.) lines were analyzed to determine protein and moisture contents, respectively using near-infrared reflectance spectroscopy. Simple correlations (${\gamma}$) of protein content in a ground sample and an intact grain sample by an automatic regression method were 0.978 and 0.910, respectively. Simple correlations by partial least square regression/principal component analysis (PLS/PCA) methods were 0.982 and 0.925, respectively. Standard error of performance (SEP) in protein content was the lowest value, 0.446 in ground sample by PLS/PCA methods. Simple correlation of moisture content was the highest at 0.871 in ground samples. when using a standard regression method. Accuracy for the moisture content was slightly lower than for protein content. It was concluded that the NIRS method would be applicable only for rapid determination of protein content in pea.

• The Journal of the Korea Contents Association
• /
• v.6 no.12
• /
• pp.21-28
• /
• 2006

In a face detection system based on template matching, histogram equalization or log transform is applied to an input image for the intensity normalization and the image improvement. It is known that they are noneffective in improving an image with intensity distortion by illumination variation. In this paper, we propose an efficient image improvement method using a simple regression analysis combined with a bilateral symmetry average for images with intensity distortion by illumination variation. Experimental results show that our method delivers the detection performance better than previous methods and also remarkably reduces the number of face candidates.

• Nutrition Research and Practice
• /
• v.16 no.6
• /
• pp.745-754
• /
• 2022

BACKGROUND/OBJECTIVES: The incidence of cardiovascular diseases (CVDs) has increased worldwide. Although a low serum vitamin D level is known to be associated with the risk of CVD, the mechanism is not well understood yet. The aim of this study was to determine the relationship of serum 25-hydroxyvitamin D₃ (25[OH]D) with homocysteine and apolipoprotein B (ApoB). SUBJECTS/METHODS: Of 777 subjects recruited from one health promotion center for routine heath exam from January 2010 to December 2016, 518 subjects were included in this study. Serum 25(OH)D, serum homocysteine, and other metabolic parameters including ApoB were analyzed. Simple and partial correlations were carried out after adjustments. Simple linear regression analysis was used for precise correlation of parameters. Multivariate regression analysis was done to know which factor (serum homocysteine or ApoB) was more related to serum 25(OH)D after adjustments. Finally, logarithms of homocysteine concentrations according to tertiles of serum 25(OH)D were compared. RESULTS: After sex and age adjustments, serum 25(OH)D showed negative correlations with serum homocysteine (r' = -0.114) and ApoB (r' = -0.098). In simple linear regression analysis, serum 25(OH)D showed a significant negative correlation with ApoB (P = 0.035). However, in multivariate regression analysis, serum 25(OH)D was significantly associated with serum homocysteine after adjustments (P = 0.022). In addition, serum homocysteine concentration was significantly high in the lowest 25(OH)D group (P = 0.046). CONCLUSION: Serum 25(OH)D concentration showed a stronger negative association with serum homocysteine than with ApoB.

• Atmosphere
• /
• v.24 no.4
• /
• pp.491-502
• /
• 2014

As a part of the KIAPS (Korea Institute of Atmospheric Prediction Systems) Package for Observation Processing (KPOP), we have developed the modules for Advanced Microwave Sounding Unit-A (AMSU-A) pre-processing and its bias correction. The KPOP system calculates the airmass bias correction coefficients via the method of multiple linear regression in which the scan-corrected innovation and the thicknesses of 850~300, 200~50, 50~5, and 10~1 hPa are respectively used for dependent and independent variables. Among the four airmass predictors, the multicollinearity has been shown by the Variance Inflation Factor (VIF) that quantifies the severity of multicollinearity in a least square regression. To resolve the multicollinearity, we adopted simple linear regression and Principal Component Regression (PCR) to calculate the airmass bias correction coefficients and compared the results with those from the multiple linear regression. The analysis shows that the order of performances is multiple linear, principal component, and simple linear regressions. For bias correction for the AMSU-A channel 4 which is the most sensitive to the lower troposphere, the multiple linear regression with all four airmass predictors is superior to the simple linear regression with one airmass predictor of 850~300 hPa. The results of PCR with 95% accumulated variances accounted for eigenvalues showed the similar results of the multiple linear regression.

• Journal of the Society of Naval Architects of Korea
• /
• v.41 no.2
• /
• pp.106-113
• /
• 2004

The block assembly of ship consists of a certain type of heat processes such as cutting, bending, welding, residual stress relaxation and fairing. The residual deformation due to welding is inevitable at each assembly stage. The geometric inaccuracy caused by the welding deformation tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurate prediction method which can explicitly account for the influence of various factors on the welding deformation. Systematic and quantitative theoretical works to clarify the effects of various factors on the welding deformation have rarely been found. Therefore, in this paper, the effects of various factors, such as welding process and gravity on the butt welding deformation have been investigated through a number of numerical analyses. In addition, this paper proposes a simplified analysis method to predict the butt welding deformation in actual plate structure. For this purpose, a simple prediction model for butt welding deformations has been derived based on numerical and experimental results through the regression analysis. Based on these results, the simplified analysis method has been applied to some examples to show its validity.

• Journal of the Korean Home Economics Association
• /
• v.39 no.2
• /
• pp.73-84
• /
• 2001

The purposes of this study were 1) to identify the effect of clothing benefit sought on fashion image sought and 2) to determine the effects of fashion image and benefit sought on purchase intention of Gal-ot. The data were collected via a self-administered questionnaire from 172 female tourist(20 to 50 ages) in Cheju and analyzed by factor analysis, stepwise multiple regression analysis and logistic regression analysis. Four factors of benefit sought were identified : Practicality/economic-value, aesthetics, reputation, and souvenir-value. Six factors of fashion image were found and labeled as: Sexy/feminine, wild/mannish, easy/simple, Cheju image, ecology and natural image. The effects of benefits sought(Practicality/economic-value, aesthetics, reputation and souvenir-value) on fashion image(Sexy/feminine, easy/simple, Cheju and natural image) were found. There were also significant effects of benefit sought(souvenir-value) and fashion image(Cheju image) on purchase intention of Gal-ot.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.2
• /
• pp.49-56
• /
• 2003

The welding deformation of a hull structure in the shipbuilding industry is Inevitable at each assembly stage. The geometric inaccuracy caused by the welding deformation tends to preclude the introduction of automation and mechanization and needs the additional man-hours for the adjusting work at the following assembly stage. To overcome this problem, a distortion control method should be applied. For this purpose, it is necessary to develop an accurateprediction method which can explicitly account for the influence of various factors on the welding deformation. The validity of the prediction method must be also clarified through experiments. This paper is aimed at deriving the simple prediction model for fillet welding deformations. For this purpose, the thermal elasto-plastic analysis varying the welding conditions and plate thickness has been performed. On the basis of numerical results, the formulae for angular distortion and transverse shrinkage have been derived through the regression analysis. Experimental work has been also carried out to clarify the validity of numerical results. It has been found that the numerical results show a good agreement with those of experiments

• The Korean Journal of Emergency Medical Services
• /
• v.14 no.3
• /
• pp.5-11
• /
• 2010

Purpose: This study was to clarify correlation between en route distance and role time on call received hours. Methods: Data on en route distance(dependent variable), role time(independent variable) from 387 prehospital care reports documented by EMS in Kyonggi Provincial Fire and Disaster Headquarters and Seoul Metropolitan Fire and Disaster Department between 21 and 10 June 2010 were randomly chosen for simple regression analysis using Windows SPSS 12. OK. This analysis was conducted nine times on unit hour divided to eight call received and overall. Results: Statistically significant regression equations( Y=2.414+1.206X for 09:00~11:59, Y=3.753+.662X for 12:00~14:59, Y=2.215+1.458X for 15:00~17:59, Y=2.600+.822X for 21:00~23:59, Y=5. 445+.263X for overall) were derieved from the data. Conclusion: These equations having linear relationship may be utilized as a method for system status management to effectively response to emergency call.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.1
• /
• pp.12-21
• /
• 2020

For quantitative evaluation of wooden structures, the mechanical performance of members has undergone outdoor exposure tests. A year-long monitoring was conducted using an SPF species. Test groups were divided into twelve (each month) to measure the moisture content, density and ultimate load. Starting from May when moisture content of the test group was at the lowest, simple failure modes were observed more frequently during the first half of the experiment, whereas complex failure modes took over during the second half. Starting from June when moisture content of the test group was the highest, ultimate load decreased by 30% in the second half compared to the first half. A multiple regression analysis confirmed that moisture content of the test group was the variable with most effect on ultimate load of various outdoor variables, and an estimation equation of a simple regression analysis revealed that moisture content and ultimate load formed an inversely proportionate relationship. It is thought that correlational relationships of variables other than moisture content could be applied with the increase in added data amount by longer periods of outdoor exposure tests.