• Journal of the Korean Institute of Gas
• /
• v.8 no.3 s.24
• /
• pp.43-51
• /
• 2004

In this study, gas permeation and separation characteristics of $CO_2$ and $N_2$ on nano-porous TPABr(Tetrapropylammoniumbromide) templating silica/alumina composite membrane were studied by using GMS (Generalized Maxwell Stefan) model. Since the transport mechanisms of meso-porous alumina support are Knudsen diffusion and viscous diffusion(or poiseulle flow), they can be identified by DGM (dusty gas model). The transport mechanism of TPABr templating silica layer, which would contribute mainly to the separation of $N_2/CO_2$ mixture, showed surface diffusion rather than pore diffusion. Therefore, the oermeationjseparation mechanisms in multi-component suface diffusion were successfully analyzed by the GMS model. In the separation of $N_2/CO_2$ mixture using the composite membrane, $CO_2$, the strongadsorbate, was permeated through the membrane more than Na due to the pore-blocking phenomena of $CO_2$ by adsorption isotherm and solace diffusion.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.7
• /
• pp.2369-2377
• /
• 2012

The gas-phase dehydration of glycerol to acrolein was carried out over silicotungstic acid ($H_4SiW_{12}O_{40}{\cdot}xH_2O$, HSiW) catalysts supported on $SiO_2$, ${\eta}-Al_2O_3$, and silica-aluminas with different Al contents. The HSiW catalysts supported on silica-aluminas showed higher glycerol conversions and acrolein yields during the initial 2 h at $315^{\circ}C$ than did $SiO_2$- and ${\eta}-Al_2O_3$-supported HSiW catalysts. Among the tested catalysts, HSiW/$Si_{0.9}Al_{0.1}O_x$ exhibited the highest space-time yield during the initial 2 h. The loaded HSiW species can change the acid types and suppress the formation of carbonaceous species on Al-rich silica-aluminas. The deactivated HSiW supported on silica-aluminas can be fully regenerated after calcination in air at $500^{\circ}C$. As long as the molar ratio between water and glycerol was in the range of 2-11, the acrolein selectivity increased significantly with increasing water content in the feed, while the surface carbon content decreased owing to the suppression of heavy compounds.

• Composites Research
• /
• v.18 no.6
• /
• pp.40-47
• /
• 2005

In this study, we tried to invent ceramic armor material with brilliant ballistic properties by the silica of the high compression-expansion ratio and based on alumina that has the most economical and higher ballistic efficiency. After we choose three compositions, proper sintering temperature for each composition was decided. After physical/mechanical measurement, we measured ballistic properties about KE(Kinetic Energy, L/D=10.7, tungsten heavy alloy) and HEAT(High Explosive Anti-Tank, K215) projectiles. As a result, $46\%\;Al_2O_3\;-\;51\%\;SiO_2$ of three compositions had the highest ballistic efficiency md better properties than alumina.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.909-914
• /
• 1995

From alumina powder and TEOS, $\alpha$-Al2O3/SiO2 composite powder for reaction-sintered mullite was synthesized by heterogeneous coagulation and surface coating, and investigated the mullitization reaction and sintering behavor of these powders. In $\alpha$-Al2O3/SiO2 composite powder prepared by heterogeneous coagulation, each alumina particles were surrounded by silica particles of 50~60 nm in size. And the alumina particles in composite powder prepared by surface coating were coated by uniform silica layer with thickness of 50 nm. In both methods, mullitization reaction was completed at 1$650^{\circ}C$ for 3h, and specimen sintered above 145$0^{\circ}C$ was about 95% fo the theoretical relative density. Mullite grains formed from the reaction with composite powders showed spherical shape with a size of 1~2${\mu}{\textrm}{m}$.

• Journal of the Korean Chemical Society
• /
• v.55 no.5
• /
• pp.812-818
• /
• 2011

[ $V_{0.9}Sb_{0.1}O_x$ ]systems, bulk and deposited on different supports (five types of ${\gamma}$-aluminas, ${\alpha}$-alumina, silica-alumina, silica gel, magnesium oxide), have been tested in the oxidative dehydrogenation (ODH) of iso-butane. This statement is derived from the data obtained by a set of characterisation techniques(specific surface area measurements, X-ray diffraction, X-ray photoelectron spectroscopy, laser Raman spectroscopy, in situ differential scanning calorimetry and in situ diffuse reflectance-absorption infrared Fourier transform spectroscopy).

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.10
• /
• pp.1330-1337
• /
• 2018

In this study, 40, 50, 60, and 70 wt% filler dispersed samples were prepared for the current GIS Spacer or environmentally friendly GIS. In the AC electrical breakdown, EMSC and EMAC decreased with increasing filler content, and EMSC showed better breakdown strength than EMAC. The mechanical properties such as tensile strength and flexural strength of EMSC and EMAC were also increased with increasing filler content. In addition, EMSC results in better mechanical properties than EMAC. The reason for this is considered to be one in which the influence of the interface is important.

• Journal of Technologic Dentistry
• /
• v.32 no.4
• /
• pp.297-305
• /
• 2010

Purpose: The purpose of this study was to observe the change of metal-mold reaction and surface roughness in titanium casting specimens for phosphate-silica alumina bonded investment with mold temperatures. Methods: The metal-phosphate silica alumina bonded mold interface reaction and surface roughness of titanium casting specimens according to mold temperatures were investigated. The Specimens were analysed by scanning electron microscopy and surface roughness tester. Results: The oxidation behavior indicated by the growth of oxide thickness. The titanium-oxide layer were consisted two layer of a porous external and a dense internal one. The reaction layer and surface roughness increased with increasing investment material temperature. Conclusion: In this work, The most suitable mold temperature in casting of pure titanium was $200^{\circ}C$.

• Proceedings of the KAIS Fall Conference
• /
• 2008.11a
• /
• pp.354-357
• /
• 2008

본 연구는 광전자촉매 시스템(PECS) 적용을 위하여 광촉매 금속판과 코팅비드를 제조하여 특성을 고찰하였다. 광촉매 물질의 회수가 용이하고, 실용화하기 위하여 티타늄 금속판을 $400^{\circ}C$에서 $700^{\circ}C$까지 $50^{\circ}C$에서 $100^{\circ}C$간격으로 토치를 사용하여 산화처리 하였으며, 비드의 경우 alumina, glass, silica gel beads에 TTIP([Ti$(OC_3H_7)_4$], Aldrich)을 전구체로 사용하여, 유동층 화학기상증착공정(Fluidized Bed Chemical Vapor Deposition, FB-CVD)으로 박막코팅을 하였다. 광촉매 금속판의 경우 산화처리 후 외관상태와 성분분석 시 최적조건은 $400^{\circ}C{\sim}500^{\circ}C$ 60분간 토치로 산화하였을 때였으며, 광촉매 코팅비드의 경우 silica gel beads가 본연의 다공구조를 나타내며 박막코팅이 되어, 상대적으로 alumina, glass beads에 비해 반응표면적이 크게 나타났다.

• Journal of the Korean Ceramic Society
• /
• v.53 no.5
• /
• pp.535-540
• /
• 2016

Effects of compositions and sintering conditions on glaze properties are shown in the diagram constructed by using the unity molecular formula (UMF) method in this study. Glossy characteristics of glaze were clearly differentiated by compositional area in the diagram and sintering process. As alumina and silica contents were increased, texture of the glaze became rough and opaque, akin to having been devitrified or underfired. The correlation between glossiness and surface roughness was found to be non-linear and inversely proportionate. Crystalline phases formed in the glaze were also influenced by the compositional area. Due to the high concentration of CaO, anorthite and wollastonite were formed depending on the compositions. Hardness was increased with an increase of alumina and silica concentrations in the glaze.

• Bulletin of the Korean Chemical Society
• /
• v.9 no.4
• /
• pp.244-248
• /
• 1988

Multilayer adsorption isotherms of nitrogen on hexagonal boron nitride, ${\gamma}$-alumina, and silica-gel powders are determined at the liquid nitrogen temperature using a gravimetric adsorption apparatus. The volume (V) of the adsorbed gas are plotted against the statistical thickness(t) of the adsorbed layer, and the t-method area are calculated from the slope of these V-t plots to compare with the BET area. A number of universal adsorption isotherms and the Frenkel-Halsey-Hill equation are used one after another in calculating the statistical thickness. The appropriateness of the FHH equation as an universal adsorption isotherm is discussed finally.