• Journal of Sensor Science and Technology
• /
• v.3 no.3
• /
• pp.28-35
• /
• 1994

Caustic Soda Treatment Systems need a concentration measurement device in order to monitor the weight reduction amount of polyester fabrics. Since the reduction process requires several concentration measurements, we have to do the unit titration fast and exactly. Therefore, a proposition of estimation algorithm for finding the equivalent point in the titration process is needed. In this paper, we used the cardinal spline algorithm, to estimate the proper curve with the measured pH-values after each injection of titration sdution, to predict the equivalent point. While the processing time is elapsed, several equivalent points are estimated and drawed the line graph of fabrics weight reduction automatically. Finally, we designed the hardware and the software of an automatic titration system that can generate the reduction ending signal of Caustic Soda Treatment System.

• Journal of Space Technology and Applications
• /
• v.2 no.2
• /
• pp.121-136
• /
• 2022

Automatic Identification System used in ship communication is required for marine control way, including monitoring of vessel operation in coastal and exchanging of information for safety navigation between them. But, it uses a very high frequency band of approximately 160 MHz, and at the same time, due to the curvature of Earth, there is a limit to the communication distance. Several demonstrations were made successfully over satellite, but not much work has been done yet through cube-satellite which has low-orbit at 500 km altitude. Here, we demonstrate a reception test of AIS (automatic identification system) receiver for a cube-satellites using software-defined radio (SDR). We collected AIS data from ship at port of Busan, Korea, using R8202T2 SDR and established to transmit them using Adam-Pluto and Matlab Simulink. The process of weakening the signal strength to a satellite was constructed using attenuator. Through above process, we demonstrated whether AIS data was successfully received from the AIS payload.

• The Journal of the Korea Contents Association
• /
• v.8 no.11
• /
• pp.182-188
• /
• 2008

The MLC(multi leaf collimator) in charge of important role in radiation therapy field recently have been exchanging from shielding block into it rapidly, owing to being convenient. However, MLC can be occurred the leakage dose of inter_leaves and the error of algorithm in imput and output from digital signal. We compared the difference of imput method to MLC made by Varian Cop. with the error and effective field induced by MLC shaper and film scanner based on XimaVision value as using MLC layer of various shapes. According to comparing standard value with them to basic MLC layer (test1-5), MLC shaper was $0{\sim}0.29cm$, $0.23{\sim}3.59cm^2$ and film scanner was $0{\sim}0.78cm$, $0.24{\sim}3.89cm^2$. At the MLC layer to be applied in clinic, MLC shaper was $0{\sim}0.54cm$, $0.04{\sim}1.68cm^2$ and film scanner was $0{\sim}0.78cm$, $0.24{\sim}3.89cm^2$. The more distance and field from axis of central line increase, the more bigger the error value increases. There is a few mm error from standard point at the process which imput various information to apply MLC in clinic. and effective field did not have variation of monitor unit and dose owing to being a few cm2 error against real field. But there are some problem to shield critical organs because some part of target volume induced by the movement of organs can be not included, therefore we have to pay attention on the process to imput MLC layer

• Progress in Medical Physics
• /
• v.6 no.2
• /
• pp.51-60
• /
• 1995

Lithium Fluoride (LiF; TLD-100) crystal chips are normally used as thermolu minescence dosimeters (abbreviated as NC-100) for estimating the absorbed dose to the skin of a patient or in a solid water phantom undergoing radiotherapy with megavoltage photon (6 and 15MV) beams. In general, investigation has revealed a reduction in the sensitivity of NC-100 chips after many runs through heating cycles. A TLD-100 chip laminated with gold plate (140${\mu}{\textrm}{m}$) on the upper surface layer of its face toward the photon beam (abbreviated as GC-100) has properties different from that of a NC-100 chip activated by incident photons and contaminant electrons with various lower energies coming from the gantry head and air. Activation of the valence band electrons of GC-100 chips by incident photons, positrons and electrons-which come from the gold plate by mainly pair production process and partly from Compton scattering-results in more enhanced signal intensity, higher response per monitor unit, as well as a good linearity with monitor units and independence of dose rate. Since the electron beams (6 and 15 MeV) do not have the probability of pair production process with gold plate, there is only a small difference (about a 3.3％ increase for 15 MeV) in the signal gaps in the TL readout for electron beams between GC- and NC-100 chips. The 3.3％ increase is entirely due to the buildup caused by the 140 m gold plate. The sensitivity of GC-100 chips is much more susceptible to high energy photon beams than electron one because of pair production. The interaction of high energy photon with a material of high atomic number, such as the good plate in this case, results in a considerably significant probability of pair production. The gold plate on the NC-100 chips acts as not only an intensifier of their signals but also acts as a filter of contaminant electrons in therapeutic high energy X-ray beams.

• Journal of Broadcast Engineering
• /
• v.17 no.5
• /
• pp.756-764
• /
• 2012

In current HEVC, prediction pixels are finally calculated by linear-function interpolation on two reference pixels. It is hard to expect good performance on the case of occurring large difference between two reference pixels. This paper decides more accurate prediction pixel values than current HEVC using linear function. While existing prediction process only uses two reference pixels, proposed method uses DCT-IF. DCT-IF analyses frequency characteristics of more than two reference pixels in frequency domain. And proposed method calculates prediction value adaptively by using linear-function, DCT-IF and cubic-function to decide more accurate interpolation value than to only use linear function. Cubic-function has a steep slope than linear-function. So, using cubic-function is utilized on edge in prediction unit. The complexity of encoder and decoder in HM6.0 has increased 3% and 1%, respectively. BD-rate has decreased 0.4% in luma signal Y, 0.3% in chroma signal U and 0.3% in chroma signal V in average. Through this experiment, proposed adaptive intra prediction method using DCT-IF and cubic-function shows increased performance than HM6.0.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.473-479
• /
• 2016

We report a highly selective and sensitive 200 MHz Surface Acoustic Wave (SAW) sensor that can detect cyanide ion in aqueous solution using surface immobilized thioester molecules in combination with gold nanoparticles (AuNPs). To construct the sensor device, a monolayer of thioester compound was immobilized on the SAW sensor surface. At the sensor surface, hydrolysis of thioester group by nucleophilic addition of cyanide occurred and the resulting free thiol unit bound to AuNP to form thiol-AuNP conjugate. For the signal enhancement, gold staining signal amplification process was introduced subsequently with gold (III) chloride trihydrate and reducing agent, hydroxylamine hydrochloride. The SAW sensor showed a detection ability of $17.7{\mu}M$ for cyanide in aqueous solution and demonstrated a saturation behavior between the frequency shift and the concentration of cyanide ion. On the other hand, our SAW sensor had no activities for other anions such as fluoride ion, acetate ion and sulfate ion, moreover, no significant interference observed by other anions. Finally, all the experiments were carried out in-house developed sensor and fluidics modules to obtain highly reproducible results.

• Journal of IKEEE
• /
• v.13 no.1
• /
• pp.41-48
• /
• 2009

This paper describes an implementation of the analog front end (AFE) incorporated with the image signal processing (ISP) unit in the SoC, dominating the performance of the CCD image sensor system. New schemes are exploited in the high-frequency sampling to reduce the sampling uncertainty apparently as the frequency increases, in the structure for the wide-range variable gain amplifier (VGA) capable of $0{\sim}36\;dB$ exponential gain control to meet the needed bandwidth and accuracy by adopting a new parasitic insensitive capacitor array. Moreover, the double cancellation of the black-level noise was efficiently achieved both in the analog and the digital domain. The proposed topology fabricated in a $0.35-{\mu}m$ CMOS process was proved in a full CCD camera system of 10-bit accuracy, dissipating 80 mA at 15 MHz with a 3.3 V supply voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.9B
• /
• pp.832-844
• /
• 2008

Distributed localization algorithms are necessary for large-scale wireless sensor network applications. In this paper, we introduce an efficient node distribution based localization algorithm that emphasizes simple refinement and low system load for low-cost and low-rate wireless sensors. Each node adaptively chooses neighbor nodes for sensors, update its position estimate by minimizing a local cost function and then passes this update to the neighbor nodes. The update process considers a distribution of nodes for large-scale networks which have same density in a unit area for optimizing the system performance. Neighbor nodes are selected within a range which provides the smallest received signal strength error based on the real experiments. MATLAB simulation showed that the proposed algorithm is more accurate than trilateration and les complex than multidimensional scaling. The implementation on MicaZ using TinyOS-2.x confirmed the practicality of the proposed algorithm.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.799-807
• /
• 2017

In this paper, a new method is proposed for estimating pedestrians' walking velocity based on lower-limb kinematics and wearable inertial measurement unit (IMU) sensors. While the soles and ground are not in contact during the walking cycle, the walking velocity can be estimated by integrating the acceleration output of the inertial sensor mounted on the pelvis. To minimize the effects of acceleration measurement errors caused by the tilt of the pelvis while walking, the estimated walking velocity based on lower-limb kinematics is imposed as the initial value in the acceleration signal integration process of the pelvis inertial sensor. In the experiment involving outdoor walking for six minutes, sensor drift due to error accumulation was not observed, and the RMS error in the walking velocity estimation was less than 0.08 m/s.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.1-9
• /
• 2011

Memristor is a portmanteau of "memory resistor". The resistance of memristor is changed depends on the history of electric charge that passed through the device and it is able to memorize the last resistance after turning off the power supply. This paper presents this device that has a high chance to be the next generation of commercial non-volatile memory and its behavior modeling using SPICE simulation. The memristor MOS content addressable memory (M_CAM) is also designed and simulated using the proposed behavioral model. The proposed M_CAM unit cell area and power consumption show an improvement around 40% and 96%, respectively, compare to the conventional SRAM based CAMs. The M_CAM layout is also implemented using 0.13${\mu}m$ mixed-signal CMOS process under 1.2 V supply voltage.