• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.5
• /
• pp.2081-2101
• /
• 2016

Successive interference cancellation (SIC) is considered to be a promising technique to mitigate multi-user interference and achieve concurrent uplink transmissions, but the optimal power allocation (PA) issue for SIC users is not well addressed. In this article, we focus on the optimization of the PA ratio of users on an SIC channel and analytically obtain the optimal PA ratio with regard to the signal-to-interference-plus-noise ratio (SINR) threshold for successful demodulation and the sustainable demodulation error rate. Then, we design an efficient resource allocation (RA) scheme using the obtained optimal PA ratio. Finally, we compare the proposal with the near-optimum RA obtained by a simulated annealing search and the RA scheme with random PA. Simulation results show that our proposal achieves a performance close to the near-optimum and much higher performance than the random scheme in terms of total utility and Jain's fairness index. To demonstrate the applicability of our proposal, we also simulate the proposal in various network paradigms, including wireless local area network, body area network, and vehicular ad hoc network.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.11
• /
• pp.5282-5300
• /
• 2017

Multi-hop cellular networks (MCNs) reduce the transmit power and improve the system performance. Recently, several research studies have been conducted on MCNs. The mobile relay selection scheme is a rising issue in the design of MCNs that achieves these advantages. The conventional opportunistic relaying (OR) is performed on the single factor for maximum signal-to-interference-plus-noise ratio (SINR). In this paper, a comprehensive OR scheme based on Bi-Target is proposed to improve the system throughput and reduce the relay handover by constraining the amount of required bandwidth and SINR. Moreover, the proposed algorithm captures the variability and the mobility that makes it more suitable for dynamic real scenarios. Numerical and simulation results show the superiority of the proposed algorithm in both enhancing the overall performance and reducing the handover.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.1
• /
• pp.44-53
• /
• 2006

In this study, the non-destructive computed tomography was adopted to observe the density profile of the needle-punched Carbon/Carbon(C/C) composites nozzle throat. The density profile of C/C was evaluated within ${\pm}0.01g/cm^3$ with 98.74% confidence when the correction of the image and high signal-to-noise ratio were achieved by the optimization of the beam hardening, the electrical noise and the scattered X-ray. The density variation of C/C with the computed tomography was in good agreement with the results obtained by the water immersion method and the observation with scanning electron microscope.

• Smart Structures and Systems
• /
• v.2 no.3
• /
• pp.253-274
• /
• 2006

The structural monitoring of multi-wire strands is of importance to prestressed concrete structures and cable-stayed or suspension bridges. This paper addresses the monitoring of strands by ultrasonic guided waves with emphasis on the signal processing and automatic defect classification. The detection of notch-like defects in the strands is based on the reflections of guided waves that are excited and detected by magnetostrictive ultrasonic transducers. The Discrete Wavelet Transform was used to extract damage-sensitive features from the detected signals and to construct a multi-dimensional Damage Index vector. The Damage Index vector was then fed to an Artificial Neural Network to provide the automatic classification of (a) the size of the notch and (b) the location of the notch from the receiving sensor. Following an optimization study of the network, it was determined that five damage-sensitive features provided the best defect classification performance with an overall success rate of 90.8%. It was thus demonstrated that the wavelet-based multidimensional analysis can provide excellent classification performance for notch-type defects in strands.

• Geophysics and Geophysical Exploration
• /
• v.16 no.1
• /
• pp.1-5
• /
• 2013

Stacking in seismic processing plays an important role in improving signal-to-noise ratio and imaging quality of seismic data. However, the conventional stacking method doesn't remove random noises with various distributions and outliers up to a satisfactory level. This paper introduces a robust and optimum weighted stack method which shows both robustness to outlier noises and optimum in removing random noises. This was achieved by combining the robust median stacking with the optimum weighted stacking using local correlation. Application of the method to synthetic data showed that the proposed method is very effective in suppressing random noises with various distributions including outliers.

• Journal of the Optical Society of Korea
• /
• v.13 no.3
• /
• pp.361-366
• /
• 2009

We propose the performance enhancing method optimization of an asynchronous 2.5 Gbps/1.25 Gbps optical subscriber network with inverse RZ (Return to Zero) coded downstream and NRZ (Non Return to Zero) upstream re-modulation by adjusting threshold level control of a receiver. We theoretically analyze the BER (Bit Error Rate) performance by modeling the occurrence of BER by simulation with MATLAB according to the types of downstream data. The results have shown that the normalized threshold level in an optical receiver could be saturated at 1/3 as the SNR (Signal to Noise Ratio) increases. The needed SNR for obtaining the BER $10^{-9}$ can be reduced by $\sim$5 dB by optimizing the normalized threshold level at 1/3 instead of by using the conventional receiver with threshold level of 0.5. The proposed system can be a useful technology for asynchronous optical access networks with asymmetric upstream and downstream data rates, because the improved minimum receiving power could replace a light source with a source with lower power and lower cost in an OLT (Optical Line Termination).

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.3
• /
• pp.7-11
• /
• 2014

The experimental analysis presented aims at the selection of the most optimal machining parameter combination for wire electrical discharge machining (WEDM) of STD11. Based on the Taguchi experimental design ($L_{27}$ orthogonal array) method, a series of experiments were performed by considering time-on, voltage, time-off, wire speed, and flow rate as input parameters. The surface roughness was considered responses. Based on the signal-to-noise (S/N) ratio, the influence of the input parameters on the responses was determined. The optimal machining parameters setting for the minimum surface roughness was found using Taguchi methodology. In order to investigate the effects of process parameters on the surface machined by WEDM, Several experiments are conducted to consider effects of time-on, voltage, time-off, wire speed and flow rate on the surface roughness. Analysis of variance (ANOVA) as well as regression analysis are performed on experimental data. The best results of surface roughness were obtained at higher voltage, lower wire speed, and lower time-on.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.4
• /
• pp.86-91
• /
• 2016

End milling is an important and common machining operation because of its versatility and capability to produce various profiles and curved surfaces. This paper presents an experimental study of the cutting force variations in the end milling of SM25C with HSS(high speed steel) and carbide tool. This paper involves a study of the Taguchi design application to optimize cutting force in a end milling operation. The Taguchi design is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer resources than a factorial design. This study included feed rate, spindle speed and depth of cut as control factors, and the noise factors were different cutting tool in the same specification. An orthogonal array of $L_9(3^3)$ of ANOVA analyses were carried out to identify the significant factors affecting cutting force, and the optimal cutting combination was determined by seeking the best cutting force and signal-to-noise ratio. Finally, confirmation tests verified that the Taguchi design was successful in optimizing end milling parameters for cutting force.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.257-258
• /
• 2006

In this paper, we address several issues in the real time implementation of MPEG-1 Layer II decoder on a fixed-point digital signal processor (DSP), especially TMS320C6416. There is a trade-off between processing speed and the size of program/data memory for the optimal implementation. In a view of the speed optimization, we first convert the floating point operations into fixed point ones with little degradation in audio quality, and then the look-up tables used for the inverse quantization of the audio codec are forced to be located into the internal memory of the DSP. And then, window functions and filter coefficients in the decoder are precalculated and stored as constant, which makes the decoder faster even larger memory size is required. It is shown from the real-time experiments that the fixed-point implementation enables us to make the decoder with a sampling rate of 48 kHz operate with 3 times faster than real-time on TMS320C6416 at a clock rate of 600 MHz.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.4 s.304
• /
• pp.25-34
• /
• 2005

We had research to conduct interrelationships between sensors using postprocessing analysis with the Fuzzy-Kalman Filtering Auto-Correlation about Real Time Simulator data of the NaroSC LCS in case of a fully blind situation scenario. The conducted interrelations are same harmony with relations in scenario. We had analyzed signals of sensors reverse-using a optimization character of Fuzzy-Kalman Filter. As our research conclusion, We had recognized possibilities of signal processing about the KSLV-1, on-board payloads, general equipments of ground support which apply to multi sensor systems.