• Journal of Electrical Engineering and Technology
• /
• v.11 no.1
• /
• pp.125-134
• /
• 2016

We propose an efficient high voltage level shifter for a high side Buck converter driving a light-emitting diode (LED) lamp. The proposed circuit is comprised of a low voltage pulse width modulation (PWM) signal driver, a coupling capacitor, a resistor, and a diode. The proposed method uses a property of a PWM signal. The property is that the signal repeatedly transits between a low and high level at a certain frequency. A low voltage PWM signal is boosted to a high voltage PWM signal through a coupling capacitor using the property of the PWM signal, and the boosted high voltage PWM signal drives a p-channel metal oxide semiconductor (PMOS) transistor on the high side Buck converter. Experimental results show that the proposed level shifter boosts a low voltage (0 to 20 V) PWM signal at 125 kHz to a high voltage (370 to 380 V) PWM signal with a duty ratio of up to 0.9941.

• Proceedings of the KIEE Conference
• /
• 1987.07b
• /
• pp.1615-1618
• /
• 1987

This paper proposes new algorithm for classifying speech signal frame into voiced, unvoiced, silence frame, using the parameters extracted from time domain behavior of speech signal The prameters used in this paper are absolute magnitude, the sum of peaks lager than reference level (T-peak), the ratio of T-peak to absolute magnitude and the magnitude of signal outputs of DPCM. Using this parameters, speech signal is more easily classified into voiced/ unvoiced/silence frame.

• Journal of the Korean Society for Precision Engineering
• /
• v.2 no.1
• /
• pp.62-71
• /
• 1985

This is a study on the monitoring technique in tool failure and tool life by AE method. The relation between amplitude level of AE signal and flank wear width was studied by experiments. The relation between amplitude level of AE signal and tool life was also studied. As the result, it was observed that amplitude level of AE signal was only affected by cutting velocity. Amplitude level of AE signal was directly proportional to flank wear width and the increasing rate was related to cutting velocity. So, the relation between amplitude level of AE signal and tool life was represented as follow: $CT^n$ = $AE_{rms}$ where, n=0.35 C=9.5*$10^{-2}$

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.809-811
• /
• 1993

The load impedance of power lines generally varies with time, areas, and season. Also, the harmonic noises by the power electrical equipments are scattered through the power lines. The received signal level varies with the environment and is not able to detect the PLC(Power Line Carrier) signal. For this reason, it is requried for the signal transmitter to hold the received signal level uniform independently with the variation of the load impedence. In this paper, the power lines are modeled simply and a method keeping the received signal level uniform is suggested through the analysis of the signal transmission characteritics of the PLC coupler using tank circuit.

• Proceedings of the KSRS Conference
• /
• 2008.10a
• /
• pp.220-223
• /
• 2008

A camera system for the satellite application performs the mission of observation by measuring radiated light energy from the target on the earth. As a development stage of the system, the signal level analysis by estimating the number of electron collected in a pixel of an applied CCD is a basic tool for the performance analysis like SNR as well as the data path design of focal plane electronic. In this paper, two methods are presented for the calculation of the number of electrons for signal level analysis. One method is a quantitative assessment based on the CCD characteristics and design parameters of optical module of the system itself in which optical module works for concentrating the light energy onto the focal plane where CCD is located to convert light energy into electrical signal. The other method compares the design\ parameters of the system such as quantum efficiency, focal length and the aperture size of the optics in comparison with existing camera system in orbit. By this way, relative count of electrons to the existing camera system is estimated. The number of electrons, as signal level of the camera system, calculated by described methods is used to design input circuits of AD converter for interfacing the image signal coming from the CCD module in the focal plane electronics. This number is also used for the analysis of the signal level of the CCD output which is critical parameter to design data path between CCD and A/D converter. The FPE(Focal Plane Electronics) designer should decide whether the dividing-circuit is necessary or not between them from the analysis. If it is necessary, the optimized dividing factor of the level should be implemented. This paper describes the analysis of the electron count of a camera system for a satellite application and then of the signal level for the interface design between CCD and A/D converter using two methods. One is a quantitative assessment based on the design parameters of the camera system, the other method compares the design parameters in comparison with those of the existing camera system in orbit for relative counting of the electrons and the signal level estimation. Chapter 2 describes the radiometry of the camera system of a satellite application to show equations for electron counting, Chapter 3 describes a camera system briefly to explain the data flow of imagery information from CCD and Chapter 4 explains the two methods for the analysis of the number of electrons and the signal level. Then conclusion is made in chapter 5.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.31 no.3
• /
• pp.411-422
• /
• 2021

The autonomous driving system mounted on the unmanned vehicle recognizes the external environment through several sensors and derives the optimum control value through it. Recently, studies on physical level attacks that maliciously manipulate sensor data by performing signal-injection attacks have been published. signal-injection attacks are performed at the physical level and are difficult to detect at the software level because the sensor measures erroneous data by applying physical manipulations to the surrounding environment. In order to detect a signal-injection attack, it is necessary to verify the dependability of the data measured by the sensor. As so far, various methods have been proposed to attempt physical level attacks against sensors mounted on autonomous driving systems. However, it is still insufficient that methods for defending and detecting the physical level attacks. In this paper, we demonstrate signal-injection attacks targeting MEMS sensors that are widely used in unmanned vehicles, and propose a method to detect the attack. We present a signal-injection detection model to analyze the accuracy of the proposed method, and verify its effectiveness in a laboratory environment.

• Progress in Superconductivity and Cryogenics
• /
• v.24 no.1
• /
• pp.29-33
• /
• 2022

Recently, development of a cryogenic fluids storage tank for storing or transporting liquid hydrogen is actively in progress. In cryogenic fluids storage tanks, hydrogen evaporates due to the extreme temperature difference inside and outside the tank. As the mass of the cryogenic fluids changes with continuous vaporization, the fluids level also changes. Therefore, there is need for a method of accurately measuring the level change in the storage tank. In the case of general cryogenic fluids, it is difficult to accurately measure the level because the dielectric constant is very low. As a method of measuring cryogenic fluids level with low dielectric constant, it can be used an Millimeter wave (MM wave) FMCW radar sensor. However, the signal sensitivity is very weak and the level accuracy is poor. In this paper, the signal sensitivity is improved by designing the horn lens antenna of the existing 80 GHz FMCW radar sensor. Horn lens antenna is fabricated by FDM/SLA type 3D printer according to horn and lens characteristics. The horn is used to increase the signal gain and the lens improves the signal straightness. This makes it possible to measure the level of cryogenic fluids with a low dielectric constant.

• Journal of Biomedical Engineering Research
• /
• v.18 no.4
• /
• pp.485-491
• /
• 1997

This paper describes the relationship between skin impedance signal, behavioral signal, and subjective evaluation depending on arousal level. Nz and reaction time had similar trend with mKSS level, but eyeblink rate was different from these two parameters. eye-blink rate increased slowly from mKSS level 1 to 5, and had high increasing rate at mKSS 7. But it showed steep descent at mKSS level 9. Each subject showed different eye-blink rates, but changing rates of EBR was similar at eachm KSS level. Therefore it suggests that rising rate of EBR can be used arousal level criterion. From the result of reaction time test. human performance was decreased rapidly above the mKSS level 5, and false positive and false negative data was observed above the mKSS level 3. It is desirable to give a subject some stimuli such as sound or aroma to rise arousal level between mKSS level 3 and mKSS level 5.

• Journal of Korean Society of Transportation
• /
• v.26 no.2
• /
• pp.89-100
• /
• 2008

In an urban network controlled by traffic signals, there is an interaction between the signal timing and the routes chosen by individual road users. This study develops a bi level programming model for traffic signal optimization in networks with path based traffic assignment. In the bi level programming model, genetic algorithm approach has been proposed to solve upper level problem for a signalized road network. Path based traffic assignment using column generation technique which is proposed by M.H. Xu, is applied at the lower-level. Genetic Algorithm provieds a feasible set of signal timings within specified lower and upper bounds signal timing variables and feeds into lower level problem. The performance of this model is investigated in numerical experiment in a sample network. In result, optimal signal settings and user equilibrium flows are made.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2022.06a
• /
• pp.228-230
• /
• 2022

본 논문은 최근 잡음 제거에서 우수한 성능을 보인 Nested U-Net의 성능을 최적화하기 위하여 두 단계로 이루어진 two-level skip connection (TLS)을 제안하였다. 이때, 인코더와 디코더의 경로를 다르게 하여 다양한 형태의 TLS을 제안하고 각 형태의 성능을 비교 평가하였다. 또한, 가장 좋은 성능을 보인 두 개의 경로를 조합하여 최종 Nested U-Net 기반 모델을 제안하였다. 제안된 모델은 다른 잡음 제거 모델과 비교하여 객관적인 평가 지표에서 매우 우수한 성능을 보인다.