• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.4
• /
• pp.501-508
• /
• 2019

In this paper, a study on a wireless check-up method of test equipment for captive flight test(CFT) was conducted. For CFT, test equipment is mounted on a POD, and check-up is carried on the test equipment's. For check-up the POD wirelessly, battery, power distribution unit, wireless communication devices were designed within the POD, and a check-up device is designed outside of the POD. Once the external check-up device sends a 'start signal' to the POD, it performs the overall check-up procedures and transmits the 'end signal' to the external check-up device. Detailed check-up results are stored in an internal storage device, and are possible to read from external check-up device if necessary, thereby improving the reliability of the wireless check-up. By implementing and applying these wireless check-up system, the reliability of the check-up was enhanced by dynamical and movable check-up, and safety is guaranteed as the check-up was carried without access to the aircraft.

• Journal of Sensor Science and Technology
• /
• v.28 no.5
• /
• pp.323-328
• /
• 2019

Recently, a sound wave phase meter (SWPM) that can directly measure the pressure waveform of sound waves in free space has been reported, and the development of educational experimental equipment using this meter is in progress. One of the main advantages of using this meter is that wavelengths can be obtained directly from the crests and troughs of the measured pressure waveforms in space without expensive equipment. However, there are times when the measurement wavelength does not exactly match the actual wavelength value, and the pressure waveform differs from the actual shape. This study was conducted to identify and analyze the causes of such errors occurring in SWPM. As a result, it was found that wavelength errors occur when the propagation direction of sound waves and the measurement direction of SWPM do not coincide. It has also been found that an error in the pressure waveform is generated when the induction and sound wave signal outputs from the SWPM interfere with each other to produce a composite signal. We have shown that we can develop educational experimental equipment by suggesting ways to reduce such errors.

• International journal of advanced smart convergence
• /
• v.6 no.2
• /
• pp.16-23
• /
• 2017

In contemporary modern society, people are constantly exposed to many kinds of noise, such as that from machinery, aircraft, construction sites, or road traffic. Noise is considered one of the most indispensable and influential parts of human life. This study investigates the acoustic characteristics of noise transfer from external sources to the human ear. For this study, we measured and analyzed various types of noise environments, installed monitoring speakers in a semi-anechoic room, and conducted intentional noise-filled experiments. In this environment, the size of the sounds generated by use of a portable device was also measured and the SNR (signal to noise ratio) calculated to study the influence of the noise. As sound is transmitted to the ear and the human body, it affects not only auditory damage but also other parts of the body. In this paper, we propose a proper SNR for noise emitted by portable IT equipment to prevent hearing loss when IT equipment is used.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.5
• /
• pp.641-649
• /
• 2016

In this paper, a novel time-domain measurement technique on a high parallelism probe card with protection resistors installed is proposed. The measured signal amplitude decreases when the measurement is performed by Needle Auto Calibration (NAC) probing on a high parallelism probe card with installed resistors. Therefore, the original signals must be carefully reconstructed, and the compensation coefficient, which is related to the number of channel branches and the value of protection resistors, must be introduced. The accuracy of the reconstructed signals is analyzed based on the varying number of channel branches and various protection resistances. The results demonstrate that the proposed technique is appropriate for evaluating the overall signal performance of probe cards with Automatic Test Equipment (ATE), which enhances the efficiency of probe card performance test dramatically.

• 유공압시스템학회:학술대회논문집
• /
• 2010.06a
• /
• pp.56-61
• /
• 2010

Simulator is a development equipment which enables the ECU to operate in normal mode by simulating the interface signal between ECU and mechanical system electrically. Embedded simulator means simulation function is embedded in ECU firmware, hence the electrical signal interface is replaced by the substitution of information at system program level. This paper explains the development of embedded transmission simulator for the verification of TCU firmware function which covers shifting control and on-board diagnosis. The embedded simulation program is executed in TCU processor along with the TCU firmware and it provides TCU firmware with not only the speed information those are appropriate both in driving and shifting conditions, but also the fault detection signals. Experimental results show that the validity of embedded simulator and its usefulness to the TCU firmware development and verification.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.2
• /
• pp.84-89
• /
• 2007

MIL-STD-461E, EMI military standard for the equipment and subsystems, requires reception characteristic tests to verify the susceptibility of a receiver against the jntermodulation and spurious signals. Because the CS103 and CS104 of MIL-STD-461E show the test configuration of the equipment unit like a traditional receiver, it is possible to verify the susceptibility only for the reception signal through analog filters. However, at present when software programming techniques make a progress, the CS103 and CS104 tests need to evaluate the reception signal of the subsystem which includes both the digital filtering effects and analog filter characteristics. These test and evaluation techniques applied to a surveillance radar subsystem. This paper researched the EMI test methods in order to confirm feasibility of these test and evaluation techniques. Also the test results are compared and analyzed.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1425-1428
• /
• 2004

Internal traffic system becomes fast with high-speed railway. Therefore, skill development for speed elevation is consisting in general railroad. New skill that is car report lake system is examined in railroad signal field. Therefore, examined establishment way and problem of car report lake system equipment. Examine equipment performance and studied method of most suitable that use.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1421-1424
• /
• 2004

Is studied for Tilting vehicles by way for speed elevation of old railroad. Therefore, examined car report lake system for New Technology introduction about control system of railroad signal. Car report lake system is system that receive information in ground and uses before train fortune. Define and function of equipments for train driving examine and defined basic equipment kind of car report lake system.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.5
• /
• pp.1562-1568
• /
• 2014

Based on the average method and the geometrical technique to calculate the average value, the average model of the open-loop step-up converter in CCM operation is established. The DC equilibrium point and corresponding small signal model is derived. The control-to-output transfer function is presented and analyzed. The theoretical analysis and PSIM simulations shows that the control-to-output transfer function includes not only the DC input voltage and the DC duty cycle, but also the two inductors, the two energy-transferring capacitors, the switching frequency and the load. Finally, the hardware circuit is designed, and the circuit experimental results are given to confirm the effectiveness of theoretical derivations and analysis.

• Proceedings of the KSR Conference
• /
• 2009.05b
• /
• pp.603-612
• /
• 2009

The bogie hunting sensor detects accelerations of a bogie. It transmits those accelerations using frequency modulated signal to the TCMS(Train Control and Management System) electronics for functional processing. TCMS decide undesirable bogie hunting and high speed instability with frequency modulated signal. The bogie hunting sensor is essential component for safety driving of high speed train. The bogie hunting sensor's quality inspection before sensor is installed on bogie is very important. Therefore it is required equipment for exact inspection of train bogie hunting sensor. This study is about development of Bogie Hunting sensor's inspection equipment that we can improve Bogie Hunting sensor's quality. Accordingly, I suppose that this thesis will be utilized to improve the bogie hunting sensor's quality thru exact inspection.