• Journal of information and communication convergence engineering
• /
• 제3권3호
• /
• pp.146-151
• /
• 2005

This paper represents an attempt to bring together and analyses the measurement data measured by the Satellite Signal Monitoring Center in Korea and the Korea Meteorological Administration/Korea Meteorological Research Institute in close cooperation with this study team. This paper presents the signal characteristic of GEO satellite operating in frequency range 1 to 20GHz associated with Asian Sand Dust (the so-called Yellow Sand Dust). The downlink signal power (dBm) for L-, S-, C-, Ku-, and Ka-band frequencies from GEO satellites were measured in a clear weather and in Asian Sand Dust weather by the Satellite Signal Monitoring Center. The measured signal power(dBm) were compared to the total number concentration and size distribution of Sand Dust that were measured by the Korea Meteorological Administration/Korea Meteorological Research Institute and the possible correlation between these sets data were analyzed. The results demonstrate that the downlink signal level (dBm) of GEO satellite is attenuated by Asian Sand Dust. Hitherto, merger information has been reported as to the influence of sand dust on satellite communications operating in regions affected by sand dust.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• 제51권4호
• /
• pp.175-182
• /
• 2002

This paper proposes an analytic method for measuring the accurate fundamental frequency component of a fault current signal distorted with a DC-offset, a characteristic frequency component, and harmonics. The proposed algorithm is composed of four stages: sine filer, linear filter, Prony's method, and measurement. The sine filter and the linear filter eliminate harmonics and the fundamental frequency component, respectively. Then Prony's method is used to estimate the parameters of the DC-offset and the characteristic frequency component. Finally, the fundamental frequency component is measured by compensating the sine-filtered signal with the estimated parameters. The performance evaluation of the proposed method is presented for a-phase to around faults on a 345 kV 200 km overhead transmission line. The EMTP is used to generate fault current signals under different fault locations and fault inception angles. It is shown that the analytic method accurately measures the fundamental frequency component regardless of the characteristic frequency component as well as the DC-offset.

• Journal of IKEEE
• /
• 제23권2호
• /
• pp.474-478
• /
• 2019

In this paper, we analyze the degradation of receiving sensitivity due to the coupling between digital noise and mobile handset antenna using characteristic mode. First, we analyze the coupling mechanism between the antenna and digital noise, and analyze the role of the decoupling capacitor of the ground signal line, which is one of the ways to improve the antenna receiving sensitivity degradation due to camera noise. For the analysis, the digital signal line and the ground line of the FPCB of the camera module are modeled as a loop type feeder that excites the characteristic mode of the PCB ground, and improved model which has a ground line with a capacitor are analyzed.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• 제31A권7호
• /
• pp.110-116
• /
• 1994

In this paper a Duty Effective Overlap Scanning method (DEOS) for the improvement of driving efficiency of LC displays which have the RMS voltage responding characteristics is proposed and new processing method of data signals for optimum application of this method is also proposed. Proposed method has a few advantages such as the increment of duty ratio the increment of driving power loaded on LC cell and the decrement of RMS voltage error rate caused by signal attenuation on electrodes composing of display when compared with the conventional method which is called as optimum voltage amplitude selection method. And also by adopting new data signal processing method which has 3 kinds of voltage levels additional advantage much improving crosstalk phenomenon which is the most serious problems of simple matrix structured display is obtained. For the characteristic estimation new mathematical representation for new overlap scanning method and data signal processing method are induced and defined. And by the defined formula and simulation the characteristics of the proposed method and the conventional method are compared and analyzed. As a result of estimation this new method being able to optimize the overlap rate of scan signal and using 3 levels of data signals has the characteristic which can improve the driving efficiency of LC displays.

• Journal of the Korean Society for Precision Engineering
• /
• 제13권11호
• /
• pp.25-31
• /
• 1996

In this paper, three different types of commercial tools -P20, NC123K and ceramic- have been used to cut austempered ductile iron(ADI). In the austempered condition the materials are hard, strong and difficult to machine. Thus, we selected a optimum tool material among three different types of used tools in machining of austempered ductile iron. It was used acoustic emission (AE) to know cutting characteristic for selected tool and investigate characteristic of AE signal according to cutting condition and relationship between AE signal and flank wear land of the ceramic tool. The obtained results are as follows ; (1) The ceramic tool among three different types of tools is the best in machining austempered ductile iron. (2) In case of ceramic tool, the amplitude level of AE signal(AErms) is mainly affected by cutting condition and it is proportional to cutting speed. (3)There have been the relationship of direct proportion between the amplitude level of AE signal and flank wear land of the tool. (4) It was observed that the value of AErms was only affected by cutting speed. Therefore it is possible to in-process detec- tion of ceraic tool's wear in case the initial value of AErms at each cutting speed decided.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• 제28A권11호
• /
• pp.910-914
• /
• 1991

This paper describes the improvement of frequency characteristic of crystal oscillator I.C using Ti-Salicide. The characteristics of transistor(drive current) using Ti-Salicide process are better than Poly-Si process, because the mobility. To know frequency characteristic of oscillator I.C, the simulation is performed using inverter buffer chain of Fan-out 10 TTL. Its result shows at once the generation of normal clock pulse in input signal and the improvement of rising and falling time.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.809-811
• /
• 1993

The load impedance of power lines generally varies with time, areas, and season. Also, the harmonic noises by the power electrical equipments are scattered through the power lines. The received signal level varies with the environment and is not able to detect the PLC(Power Line Carrier) signal. For this reason, it is requried for the signal transmitter to hold the received signal level uniform independently with the variation of the load impedence. In this paper, the power lines are modeled simply and a method keeping the received signal level uniform is suggested through the analysis of the signal transmission characteritics of the PLC coupler using tank circuit.

• Journal of Biomedical Engineering Research
• /
• 제10권3호
• /
• pp.285-288
• /
• 1989

A characteristic proton NMR signal is found in human cancer serums. The signal is given by $6.43{\pm}0.06$ ppm on average. An attempt is made to find a certain correlation between the appearance of the signal and the amounts of CEA and AFP in the serums.

• Journal of Biomedical Engineering Research
• /
• 제5권1호
• /
• pp.5-8
• /
• 1984

As the ensemble averaged dz/dt signal during exercise gets smoothed, it is difficult to find the distinctive marks for estimation of stroke volume. The cross correlation function was made use of estmating these marks for automatic calculation by computer from the ensemble averaged dz/dt signal. LVET(Left Ventricular Ejection Time) and stroke volume were estimated based on the calculated parameters from the characteristic points. LVET, stroke volume calculated by hand, by the ensemble average and the cross correlation were compared for accuracy validation.

• Proceedings of the KIEE Conference
• /
• 대한전기학회 1988년도 전기.전자공학 학술대회 논문집
• /
• pp.51-54
• /
• 1988

In this paper, Digital signal processing method is deserved by the tissue characteristic quantization. Linear phase velocity is studied using linear signal, and the slope which attenuation characteristics are decreased is analysed according to frequency increase. A more efficient method determining the minimum phase function is developed from the spectral magnitud function.