• 수산해양기술연구
• /
• 제50권3호
• /
• pp.378-384
• /
• 2014

Trawlers are divided into stern and side types by the method of shooting and hauling net, but the latter is difficult to find beside Korea. In East Sea of Korea, the side type used to be in early 2000's, but it improved to stern type because of its inefficient operating method. The aims of this paper is to make clear the stability of the side trawler in the East Sea, and then confirm whether it satisfy the IMO rule or not, the degree of the transverse inclining angle of the ship when hauling net at hull side. In results, the stability of the ship in initial inclining range satisfied the IMO rule and the domestic rule, but not satisfied those rule in over the range. The limit load of the ship that was coincide with the angle of beam end in hauling net at side was about 26 tons, 18 tons in normal sea condition and storm warning condition respectively. The transverse inclining angles of the ship in hauling net were much higher from 3.3 to 5.5 times than the longitudinal inclining angle of the stern trawler, although those angles were slightly changed with depending on the loading and sea condition.

• 수산해양기술연구
• /
• 제52권2호
• /
• pp.162-168
• /
• 2016

This study attempted to help determine Korean fishery policies by proposing improvement plans after examining the current regulations, fishing vessels, fishing gear and fishing methods of the middle sized trawl fishery in the East Sea for targeting only squid. In general, the size, engine horse power, and net length of the middle sized trawlers are between 50 and 60 GT, 1,200 and 1,600 PS, and approximately 165 m with four seamed trawl nets, respectively. While a jigging vessel attracted squids using lights, the trawler approached a jigging vessel. The trawler let the jigging vessel know its decision for fishing, and then jigging vessel rolled up jigs. The net of the trawler was casted at 45 degrees between the bow and the stern of the jigging vessel. Once the trawler towed close to the stern of the jigging vessel upon its passing of the jigging vessel, the bow of the trawler turned 45 degrees left again. Then, squid aggregations were entered into the net. When the cod end was passed a light vessel, the trawler hoisted the net up to the otter board. Then the trawler turned 180 degrees. It repeated three to five times of fishing operations as the previous method. We recommend that the regulations allow nineteen side trawlers to catch like stern trawler, as well as the cooperative trawler and jigging vessel operations.

• 수산해양교육연구
• /
• 제6권1호
• /
• pp.11-19
• /
• 1994

The North Pacific midwater trawling which is one of the important fishing methods for Korean fishing industry is working in the Bering Sea and the sea near Kamchaka Peninsula. The catch by Korean midwater trawlers had been recorded about 300 thousands $^{M/_T}$ a year. Six types of midwater trawl net-ordinary midwater trawl net, super-V trawl net, super mesh trawl net, rope trawl net, super plus trawl net and kite trawl net-have been widely used by large trawlers above 1,500gt in size since 1982. Regarding the fishing efficiency, the super plus trawl net and kite trawl net were acknowledged as higher than other nets. Maximum mesh size of super-plus trawl net and kite trawl net ranges about 20m, whereas the length of net about 150m, and high-tech polyethylene is used as the material of rope part. The problems involved in the North Pacific midwater trawl net may be summarized as follows ; (1) The dimension of fishing gear is too big compared with the towing power of trawler. (2) The mesh size of the rope part is too big compared with that of the common netting part. (3) The net is often torn out in the connecting position of the rope part and the netting part. (4) The net is not matched with the trawler and the otter board in many trawlers, so the shape of the trawl gear in the water is instable. (5) The fish school located near head rope, ground rope and side rope in the net recorder is not caught in practice because of the net instability.

• 수산해양기술연구
• /
• 제25권2호
• /
• pp.70-74
• /
• 1989

실험선 제주 402호의 조종성능을 전속전진중 최대타각으로 전타한 때의 선회권측정과 $10^{\circ}$, 20$^{\circ}$, 30$^{\circ}$Z시험에서 산출된 조종성지수를 분석, 검토한 결과를 요약하면 다음과 같다. 1. 선회종거는 우현선회시가 79.1m로 배의 길이의 약 2.6배였으며, 좌현선회시는 81.4m로서 배의 길이의 약 2.7배였다. 또, 선회경은 배의 길이의 약 2.6배로서 우현선회시가 78.3m로서 좌현선회시 80.4m보다 작았다. 2. 선회권시험시 속력저감율은 0.49였으며, 평균선회각속도는 우현선회시가 4.3$^{\circ}$/sec, 좌현선회시는 4$^{\circ}$/sec이었다. 3. Z시험 결과 over shot angle은 우현전타시가 좌현전타시보다 더 컸으며, 좌우타전타시의 평균값은 $10^{\circ}$Z시험시가 10.5$^{\circ}$, 20$^{\circ}$Z시험시가 20.5$^{\circ}$, 30$^{\circ}$Z시험시가 29.5$^{\circ}$로 다소 큰 편이었다. 4. $10^{\circ}$, 20$^{\circ}$, 30$^{\circ}$Z시험에서 K' 및 T'의 값은 각각 0.755, 0.566, 0.481 및 3.468, 1.621, 1.547로서 대체적으로 선회성은 대각도 전타 일수록 나쁘거나, 추종성은 대각도 전타 일 수 록 좋았다.

• 수산해양기술연구
• /
• 제53권4호
• /
• pp.337-348
• /
• 2017

The tension of warp from trawler and sea-floor contact can generate tilt and wake turbulence around otter boards. Preliminary measurements of otter board tilt and 3-D flow velocity during bottom trawl operations were taken using a vector instrument to investigate the effects of wake turbulence at the trailing edge of the otter board. Tilt data (i.e., yaw, pitch, and roll) at 1 Hz and flow data (velocities in the towing, lateral, and vertical directions) at 16 Hz were analyzed to determine their periods and amplitudes using global wavelet and peak event analyses. The mean period (${\pm}standard$ deviation) of the tilt from the peak event analysis ($5{\pm}2s$) was longer or double than that of flow velocity ($3{\pm}2s$). The two periods also had a significant linear relationship. The turbulence rate of flow was 30-50% at the trailing edge and was closely related to roll deviation. The frequency of phase difference ratios (i.e., peak time differences between tilts and flow periods) was significantly different from random occurrence in two trials, possibly due to side tidal effects. However, in the other trials, flow peaks were random, as shown by the even peak times between tilts and flows. Future studies should focus on reducing tilt variation, wake turbulence, and bottom contact to stabilize otter board motion.

• 수산해양기술연구
• /
• 제40권4호
• /
• pp.311-318
• /
• 2004

실해상 실험을 통하여 해상의 조건이 동일할 때, 예망과 항해중일 때의 만남파에 대한 소형 트롤어선의 종동요와 횡동요의 응답특성을 통계적 방법과 이론적인 방법을 이용하여 분석하였다. 그 결과를 요약하면 다음과 같다. (1) 종동요의 응답 크기를 예망중과 항해중에 따라 비교하면 큰 차이가 없으나, 선수쪽에서 파를 받을 경우에는 항해중의 응답이 예망중 보다 양각 커지는 경향이 있다. (2) 횡동요의 응답은 예망중과 항해중 모두 종동요에 비해 매우 크다. 그러한 경향은 모든파향에서 현저하지만, 횡파를 받을 경우에는 양자의 응답 차이는 줄어든다. (3) 예망중과 항해중 모두 종동요에서 응답스펙트럼의 peak가 나타나는 주기는 파향에 관계없이 거의 일정하다. (4) 선미쪽에서 파를 받고 예망할 때, 양현에 균등하게 warp의 힘이 작용한다면, 어구의 저항은 동요를 감쇄시키는 상당한 효과가 있다.

• 한국수산과학회지
• /
• 제18권1호
• /
• pp.1-7
• /
• 1985

본연구에서는 전개장치를 띠모양의 소형 범포들로 구성하는 띠전개범식 안강망어구를 고안하여 재래의 그들을 이용한 1/3 모형어구 및 그물을 개량한 실물어구를 각각 제작하여 실험하였던 바, 다음과 같은 결과를 얻었다. 1. 재래의 안강망어구의 축척비 1/3인 모형어구의 총저항 R(kg)을 실물로 환산하면 $R=5.6{\times}10^{3}V^{l.5}$ 또는 $R=3.5\frac{d}{l}{\lambda}_b{\lambda}_l\;V^{1.5}$로 주어진다. 단, V 유속(m/sec), d는 그물실의 직경, l은 그물코 다리 한개의 길이, ${\lambda}_b$는 그물아궁이의 뻗친 둘레(m), ${\lambda}_l$은 그물의 뻗친 길이(m)이다. 2. 모형실험에서 망고는 유속에 따라 거의 일정하며 옆줄 길이의 $83\%$ 정도로 유지하였다. 3. 망폭은 유속의 증가에 따라 서서히 감소하여 유속 1m/sec 일 때 모형실험에서는 뜸줄길이의 $90\%$정도, 실물실험에서는 $95\%$정도 유지하였다. 4. 어구조작은 선미식 트롤어선으로 행한 결과 전개장치의 선미경사로 통과가 여의치 않았고 장망시 선미경사로상에서 뜸줄, 발줄 및 옆줄이 뒤로 쳐져 엉키는 현상이 일어났다.

• 수산해양기술연구
• /
• 제28권1호
• /
• pp.21-26
• /
• 1992

Generally a navigator evaluated the maneuverability of his ship by the scale of turning circle which was described only by the largest rudder angle of the port and starboard sides. But to have the sufficient knowledge of his ship's maneuvering characteristics he should consider the data about the new course keeping test, the spiral test, and the turning circle tests in accordance with the rudder angles together. In this paper the author performed the above tests to study the maneuverability of the stern trawler M.S. Pusan 404 which is a training ship of the National Fisheries University of Pusan. The obtained results are summarized as follows: 1. When the rudder angles being 5。, 10。, 20。, 30。, 35。 the advances of the starboard side turning circles were 12.8, 8.2, 4.8, 2.9, 2.7 times as large as the length of the ship, and of the port side turning circles were 13.3, 8.7, 5.4, 3.5, 2.9, time as large as the large as it. Under the same conditions the tactical diameters were 15.1, 9.7, 5.2, 3.1, 2.8 times as large as the length of the ship, for starboard side, and 17.2, 12.4, 6.4, 3.7, 3.2 times as large as it for port side. 2. As the rudder angle being increased the ratio of the advance to the tactical diameter was nearly 1 and her obeying ability was better than that of the small angle. 3. The mean values of the rates of speed reduction during the steady turning motion were 0.96, 0.92, 0.82, 0.71, 0.65 in accordance with the rudder angles. 4. The relative formulas between the distance to the new course y and the altering course x were as follows: When rudder angles being 10。, 20。, 30。, y=52.2222+1.6133x, y=48.750+0.9383x, y=39.250+0.655x respectively. 5. There was little difference of the distance to the new course between rudder angle 20。and 30。, and so it is desirable for a navigator to a navigator to use the small rudder angles unless sudden emergencies. 6. Though her rudder angle being small her course stability was good according to the spiral tests.

• 수산해양기술연구
• /
• 제51권4호
• /
• pp.520-526
• /
• 2015

A tragic disaster happened by capsizing O-Ryong 501 trawler at Western Bering Sea in 1st, Dec. 2014. The disaster was caused by the severe weather and the long deferred escape from the storm in fully developed high sea. Lots of sea water from poop deck rushed into the fish ponder with fishes all together after hauling net and then remove the fishes from codend. The vessel became to incline to the one side caused by the weight and the free surface effect of flood sea waters and fishes at initial stage. In spite of crews all effort to discharge the waters, but the work was not achieved successfully. For the worse thing, the order of abandon ship was issued too late. After all, the ship capsized and sank, then almost crews became to the victims of the casualty including captain. In this paper, author carried out restrictively the calculation of dynamic factors influenced on the disaster including the weather condition and effects of the flood sea waters, and found out that the most important causes of the disaster were the decrease of stabilities, GM was decreased from 0.9m to 0.08 m, and the high waves which led to the vessel disaster.

• 수산해양기술연구
• /
• 제29권3호
• /
• pp.200-213
• /
• 1993

A model experiment on a midwater rope trawl net which is used in the North Pacific to catch alaska pollack is carried out in the circulating tank to examine the basic efficiency of the net. The prototype is the net used by M/S Hanil(1, 179GT, 2, 700PS), a Korean trawler. The model net was made according to the Tauti's Similarity Law of Fishing Gear in 1/100 scale by considering the condition of the tank. To measure the basic efficiency of the standard model net, the vertical opening and width between some points marked on the net were measured, and the hydrodynamic resistance were determined. Then the constructive conditions of the net were varied as follows and the factors were measured again to compare the efficiency of those nets with that of the standard net(A-1 type) front weight multiplied 1.5 times: A-2 type. buoyancy and depressing force multiplied 1.7 times: A-3 type. front weight multiplied 1.5 times on A-3 type: A-4 type. depressors rigged at ground rope: B type. cod-end stuffed with cashmylon wad: C type. The results obtained can be summarized as follows: 1. The vertical opening at the center of head rope was steeply decreased with the flow velocity increasing and the vertical opening H(m) can be expressed in H=1.2v super(-1.2)(v : flow velocity in m/sec). The width of the net varied a little when the flow velocity was over 0.4m/sec, and the width of net mouth showed about 37% of the distance between the fore tips of net pendant. The shape of net mouth was almost a circle at 0.2m/sec and then steeply flatted elliptically with the flow velocity increasing and the area of mouth S(m super(2)) can be expressed in S=(1.65-2.3v)$\times$10 super(-2). The hydrodynamic resistance of the net increased almost linearly with the flow velocity increasing and the resistance R(kg) can be expressed in R=3.2$\times$d/l$\times$abv. where d/l denotes the mean of d(diameter of netting twine) and l(length of a leg in a mesh) from wing tip to the end of bag-net except cod-end on the side pannel, and a denotes the strectched circumference of the net at the fore end of a meshed part and b the stretched length of the whole net from wing tip to the end of cod-end. 2. In the condition-varied nets, the vertical opening of head rope showed some increase in every type net except the C type, and the increase showed the greatest in the B type by 30~54%, whereas it showed decrease in the C type by 5~10%. Variation of the area of net mouth showed almost the same tendency as the vertical opening and the increase showed the greatest in the B type by 20%, whereas it showed decrease in the C type by 12%. Hydrodynamic resistance showed some increase in every type compared with the standard net, and the rate of increase indicated 5~10% in the A-2, A-3 and A-4 type, 22% in the B type and 3% in the C type.